Abstract:Catalytic combustion has been widely applied to remove the trace combustible pollutants. However, the earth-abundant and high-performance nanocatalysts are still the main research focus on promoting catalytic efficiency. Herein, the Cu and Mn mixed oxides supported on TiO2 nanoparticles with various Cu and Mn molar contents synthesized via the flame spray pyrolysis (FSP) technique are utilized in the catalytic oxidation of lean CO and CH4. Initially, the Cu–Mn/TiO2 nanocatalysts are composed of spherical structures with a diameter of about 20 nm, whose specific surface area is between 60 and 90 m2/g. The Cu element is more evenly distributed on the TiO2 surface than the Mn element, owing to the distinctly different ion radii. Both the copper and manganese cations could incorporate into the TiO2 lattice, which generates oxygen vacancies and enhances the diffusion of oxygen ions, causing the transformation of the antanse to rutile phase. When the molar content of the Cu–Mn increases to less than 30 mol %, the temperature of its reduction peak keeps decreasing due to the hydrogen spillover effect. Moreover, the catalytic performances of the Cu–Mn/TiO2 with 12 mol % loading (12CMT) are all optimal during the low-temperature and the high-temperature stages, which are superior to the FSP-made copper manganese or copper titanium oxides. This is attributed to the small crystal particles, highly dispersed active components of CuOx and MnOx, and the higher ratios of Cu1+/Cu and Mn4+–Oads Lewis acid–base pairs. In addition, the strong interaction between Cu–Mn components and rutile phase support can tremendously promote the activity of catalytic combustion. Under the simulated flue gas, the catalytic properties of 12CMT decreases in comparison with those of CO and CH4 mixed gas due to the introduction of CO2. Ultimately, the Cu–Mn/TiO2 samples exhibit the outstanding water resistance, thanks to the hydrophobization of the catalyst surface.This article has not yet been cited by other publications.

Catalytic Combustion of Methane over Sncuo Catalysts

Pd4S/SiO2: A Sulfur-Tolerant Palladium Catalyst for Catalytic Complete Oxidation of Methane

Sulphur Poisoning Mechanism of Sno2 Based Catalysts for Methane Combustion

Complete Oxidation of Methane on Co 3 O 4 -Sno 2 Catalysts

Catalytic Combustion of Methane over Tin Dioxide Supported Silver Catalysts

Catalytic combustion of lean methane over MnCo2O4/SiC catalysts: Enhanced activity and sulfur resistance

Catalytic elemental sulfur-assisted methane activation at low temperature

Isotopic Studies of Sn-Cr Binary Oxide Catalysts for Methane Total Oxidation

Combustion Synthesis of Non-Precious CuO-CeO2 Nanocrystalline Catalysts with Enhanced Catalytic Activity for Methane Oxidation

Surface characterization and methane activation on SnO x /Cu 2 O/Cu(111) inverse oxide/metal catalysts

Oxidative coupling of methane over Mo–Sn catalysts

In Situ Sulfation of Cu/TiO2 Catalysts for Catalytic Combustion of Dichloromethane

One-Step Synthesis of Nanostructured Cu–Mn/TiO 2 via Flame Spray Pyrolysis: Application to Catalytic Combustion of CO and CH 4

Methane Combustion over the Porous Oxides and Supported Noble Metal Catalysts

Low-Temperature Combustion of Toluene over Cu-Doped SmMn<sub>2</sub>O<sub>5</sub> Mullite Catalysts via Creating Highly Active Cu<SUP>2+</SUP>-O-Mn<SUP>4+</SUP> Sites

Coupling of Dielectric Barrier Discharge and Cu–S-1 Catalyst for Direct Oxidation of Methane to Methanol

Investigation of catalytic methane oxidation over Ag/Co2MOx (M = Co, Ni, Cu) catalysts with varying interfacial electron transfer

Transition Metal (Ni, Cu and Fe) Substituted Co3O4 – ZrO2 Catalysts for Lean Methane Combustion

Nickel Oxide As an Effective Catalyst for Catalytic Combustion of Methane

Promotional Effect of CeO2 and Y2O3 on CuO/ZrO2 Catalysts for Methane Combustion

Complete Combustion of Methane over Indium Tin Oxides Catalysts