Abstract:The efficient, safe and eco-friendly disposal of the chromium-containing sludge (CCS) has attracted an increasing concern. In this study, Co-processing of CCS was developed via employing sintering and ironmaking combined technology for its harmless disposal and resource utilization. Crystalline phase and valence state transformation of chromium (Cr), technical feasibility assessment, leaching risk, characteristics of sintered products, and pollutant release during CCS co-processing were investigated through a series of laboratory-scale sintering pot experiments and large scale industrial trials. The results showed that the content of Cr(VI) in sintered products first increased then decreased with increasing temperature ranges of 300 °C–800 °C, and reached a maximum of 2189.64 mg/kg at 500 °C. 99.99% of Cr(VI) can be reduced to Cr(III) at above 1000 °C, which was attributed to the transformation of the Cr(VI)-containing crystalline phases (such as, MgCrO 4 and CaCrO 4 ) to the (Mg, Fe 2+ )(Cr, Al, Fe 3+ ) 2 O 4 . The industrial trial results showed that adding 0.5 wt‰ CCS to sintering feed did not have adverse effects on the properties of the sintered ore and the plant's operating stability. The tumbler index of sinter was above 78% and the leaching concentrations of TCr (0.069 mg/L) was significantly lower than the Chinese National Standard of 1.0 mg/L (GB5085.3–2007). The TCr contents of sintering dust and blast furnace gas (BFG) scrubbing water were less than 0.19 wt‰ and 0.11 mg/L, respectively, which was far below the regulatory limit (1.5 mg/L, GB13456-2012). The mass balance evaluation results indicated that at least 89.9% of the Cr in the CCS migrated into the molten iron in the blast furnace (BF), which became a useful supplement to the molten iron. This study provided a new perspective strategy for the safe disposal and resource utilization of CCS in iron and steel industry.

Industrial tests of retrofitting Soderberg cells to prebake cells

Examination of Industrial Demonstration Unit of Coal Gasification for Pulverized Coal with Ash Agglomeration Technique

Remediation of Chromium-Slag Leakage with Electricity Cogeneration Via a Urea-Cr(vi) Cell

An assessment of environmental impacts and economic benefits of multiple aluminum production methods

AP35: The Latest High Performance Industrially Available New Cell Technology

Mixed-Framework-Based Energy Optimization of Chemi-Mechanical Pulping

Retrofitting Strategy and Operating Technology of Pure Burning Zhundong Coal in a 135 MW Circulating Fluidized Bed Boiler

Resource utilization strategies for spent pot lining: A review of the current state

Optimizing Wet Hydrolysis for Nitrogen Removal and Alumina Recovery from Secondary Aluminium Dross (SAD)

R&D of a new technology of conversion of coke oven gas from bituminous coal into syngas

Detoxication and recycling of chromium slag and C-bearing dust via composite agglomeration process (CAP)-blast furnace method

Environmental and Economic Assessment of Pre-Training Electrolytic Aluminum Production - A Case Study of China

Study on Optimization Experiment of SCR Denitrification Technologies in a Coal-fired Power Plant

A Numerical Approach on Waste Heat Recovery through Sidewall Heat-Exchanging in an Aluminum Electrolysis Cell

Operating experience of CFB semi-dry FGD with novel humidification technology in China

Treatment of chromium-containing sludge using sintering and ironmaking combined technology: A risk-reducing strategy for environmental impact

An efficient and clean treatment of spent carbon cathode via fluorination roasting: Deep separation strategy for insoluble aluminosilicates

Life cycle greenhouse gas emissions of aluminum based on regional industrial transfer in China

Reconstruction and Operation Effects of Silica Gel Ball Cleaning System of No.6 Unit of Zhangjiakou Power Plant

Selective preparation of lithium carbonate from overhaul slag by high temperature sulfuric acid roasting - Water leaching

Environmental and economic impact assessment of three sintering flue gas treatment technologies in the iron and steel industry