Abstract:In recent years, oxy-fuel combustion in coal-fired plants has become one of the most promising technologies for carbon capture and storage (CCS). Compared with air-fired combustion, high concentrations of CO2 and H2O in the flue gas cause a remarkable change in the pulverized coal combustion and heat transfer characteristics in furnace. In this study, improved models for the gas radiative properties and chemical reaction mechanisms were incorporated into the computational fluid dynamics (CFD) code to simulate a 200 MWe tangentially fired utility boiler, which is expected to operate at full load under both conventional air-fired and oxy-fuel combustion. Different flue gas recycle patterns: dry recycle and wet recycle, were also investigated. The results indicate that, stable combustion is achieved by a compatible burner design in both air-fired and oxy-fuel combustion. In the oxy-fuel combustion, the flue gas peak temperature and wall heat flux decrease and high CO concentration appears in the burner region, resulted from higher heat capacity of CO2 and chemical effect of CO2 (Liu et al., 2003, Glarborg and Bentzen, 2008). Based on the comparison of the wet recycle and dry recycle, it shows the wet recycle has more advantages than dry recycle. This study indicates a slight increase in total heat transfer, when the oxygen concentration in oxidant increases from 23% to 29%, consistent with the results of Vattenfall and Callide pilot scale oxy-combustion plant. Thus, compared with air-fired combustion, the full load of a boiler may decrease by 5-10% under oxy-fuel combustion. (C) 2014 Elsevier Ltd. All rights reserved.

Computational Modeling of Tangentially Fired Boiler (I) Models, Flow Field and Temperature Profiles

Computational modeling of pulverized coal combustion processes in tangentially fired furnaces

Modeling of Combustion Process in 600 Mw Utility Boiler Using Comprehensive Models and Its Experimental Validation

Numerical Investigation on Oxy-Combustion Characteristics of a 200 MWe Tangentially Fired Boiler

NUMERICAL MODELING OF 3-D ISOTHERMAL FLOW IN TANGENTIALLY-FIRED BOILER WITH BODY-FITTED MESHES

Computational Modeling of Tangentially Fired Boiler (ii) Nox Emissions

Combustion Modeling Of Cfb Boiler Furnace Based On An Euler-Euler Approach

CFD investigation on the flow and combustion in a 300 MWe tangentially fired pulverized-coal furnace

Numerical simulation of the two-phase flow and combustion in the tangential-firing boiler furnace by using the ALE algorithm and trajectory model

Two-Dimensional Combustion Modeling Of Cfb Boiler Furnace Based On An Euler-Euler Approach And The Kinetic Theory Of Granular Flow

Simulation of 3-D gas-particle flows andcoal combustion in a tangentially-fired furnace modelusing a two-fluid -traje ctory model

Integrated Numerical Model for Ultra/Supercritical CFB Boilers

Numerical Simulation of the Flow and Combustion Processes in a Three-Dimensional, W-Shaped Boiler Furnace

E304 FLOW FIELD IN A MODEL OF A 2950 T/H TANGENTIAL-FIRED BOILER UNDER DIFFERENT CONDITIONS OF SEPARTED OVER-FIRE-AIR INJECTIONS(Boiler-1)

Influence of the turbulence model on the numerical predictions of cold turbulent flow in a heavy-duty gas turbine DLN combustor

Modeling of Coal Combustion and NOx Formation in a W-shaped Boiler Furnace

Flow Field In A Model Of A 2950 T/H Tangential-Fired Boiler Under Different Conditions Of Separted Over-Fire-Air Injections

Numerical studies on the flow field in the tangential firing boiler furnace

Numerical Simulation Of The Combustion Processes In A W-Shaped Boiler Furnace Under Different Operating Conditions

Study on Fluid Flow Characteristics in Different Load Cases in Tangentially Fired Furnaces

Numerical and Experimental Study on Nonlinear Phenomena and Thermal Deviation Control in a 1000 MW Tower-Type Boiler