Abstract:Functional gradient materials (FGM), with their composition gradually varied in different positions, have attracted much attention for research and development during the years. Normally there are two types of functional gradient materials: one without the formation of intermetallics which is easier for fabrication due to less scientific and technological challenge; the other one with the formation of intermetallics in some part of the gradient changed composition range such as Ti-Al, Ti-Fe, Ni-Al gradient materials, which still exists big challenge on intermetallic, resulting in high brittleness and unavailability.Laser deposition is a competitive candidate for FGM due to its capability on accurate composition and precise dimension control. According to an aeronautical application requirement to gradually change the composition from Ti6Al4V to 316L, this paper reports on laser deposition of Ti6Al4V to 316L gradient composition structure. A big challenge is the formation of the TiFe intermetallic especially near the composition of Ti50Fe50, which results in very high cracking tendency. Many efforts have been made to optimize the Ti-Fe composition ratio, the deposition process and the deposition parameters, not a single Ti6Al4V-316L composition gradient structure was successful due to the formation of the very brittle TiFe and TiFe2 intermetallics. This indicates that it is almost impossible to direct deposit Ti6Al4V to 316L without cracking and separation. We used Inconel 625 powder as an interlayer between the Ti6Al4V and the 316L, thus a sound Ti6Al4V-316L composition gradient structure was successfully achieved by laser deposition. The brittle TiFe and TiFe2 intermetallics were replaced by a series of phase evolutions: α+β → β+Ti2Ni→Ti2Ni+TiNi→TiNi→TiNi+TiNi3→Ni3Fe→ Ni2Fe3→γFe. The brittleness was dramatically decreased or diluted and crack-free composition gradient structure was available. The gradient structure was further analyzed on hardness, microstructural evolution, the Young's modulus and Poisson's ratio.

PREPARATION AND MICROSTRUCTURE OF Ti-ZrO2 GRADIENT MATERIALS

Effects of Zr Addition on the Deformation Behavior, Microstructure and Mechanical Properties of Dental Ti Alloys

Microstructures of Ni–ZrO2 functionally graded materials fabricated via slip casting under gradient magnetic fields

Al2O3/ZrO2 Functionally Graded Material Made by Extrusion Gelation Freeforming Processing

Progress in Titanium Matrix Functionally Gradient Materials Complex Structure

A functionally graded coating from ZrN to Ti: Experimental characterization, erosion behavior and design concept

Study on Microstructures and Mechanical Properties of Layered and Layered‐Gradient Zr/Ti Materials

Microstructure and Mechanical Properties of Ti60-Ti2alnb Functionally Graded Materials Fabricated by Laser Directed Energy Deposition

Integrated preparation and enhanced performance of high-melting-point ZrC–Mo multilayer graded materials

Synthesis of Functionally Graded AA7075-B4C Composite with Multi-Level Gradient Structure

Characterization of Interfacial Transition Zone of Functionally Graded Materials with Graded Composition from a Single Material in Electron Beam Powder Bed Fusion

A New Approach for the Preparation of Functionally Graded Materials Via Slip Casting in a Gradient Magnetic Field

Laser Deposition of Ti6Al4V-316L Composition Gradient Structure: Challenge on Intermetallics

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

Preparation of Zr-based metallic glasses gradient composites with designable amorphous fraction by laser powder bed fusion

Microstructure characterization of gradient composition between TC25G and TiAl alloys prepared by directed energy deposition technique

Design of Functionally Graded Ti–Al Alloy with Adjustable Mechanical Properties: a Molecular Dynamics Insights

Preparation and characterization of Al2O3–Ti3SiC2 composites and its functionally graded materials

Research on the microstructure and mechanical properties of functional gradient materials of TC4/TC11 titanium alloys for wire arc additive manufacturing with different transitional forms

Effects of TiB2 content and gradient structure on microstructural characterization and mechanical properties of TiB2/Al7050 composites

Functionally graded materials with grain-size gradients and heterogeneous microstructures achieved by additive manufacturing