Analysis of Torque-Current Characteristic of Brushless DC Motor Driven by Three-Phase H-bridge

尚静,邹继斌,胡建辉

2000-01-01

Abstract:Presents the simulation and analysis of the steady state characteristic of a brushless DC motor studies the torque current characteristic of the motor as well and discusses the design of a current measure circuit for torque controlling.

What problem does this paper attempt to address?

Steady Performance Analysis on Single-Phase Brushless DC Motor

Lijian Wu,Wanbing Jin,Yi Liu,Jianping Ying

DOI: https://doi.org/10.1109/icems12746.2007.4412188

2007-01-01

Abstract:Single-phase brushless DC motor (SPBLDCM) has always been difficult to accurate computer-aided analysis, design and optimization for the lack of appropriate mathematical model of the motor. However, due to simple structure and high efficiency, it is widely used in low cost applications that require low starting torque. In the paper, a linear steady model of SPBLDCM is developed to predict the performance of the motor. It is suitable for the initial design and optimization of the motor geometry because of its low computational complexity. The optimal commutation advance angles for two different objectives, high electromagnetic power and low current ripple, are also presented based on this linear steady model The performance of the prototype is analyzed by both the developed linear steady model and the dynamic model. Both results agree well. The experimental results also validate the effectiveness of the model.
Research on PWM Method in Brushless DC Motor

WEI Kun,LIN Ping,Xiong Yu,ZHANG Zhong-chao

DOI: https://doi.org/10.3785/j.issn.1008-973x.2005.07.025

2005-01-01

Abstract:The influences of the torque ripples in the commutation interval and non-commutation zones, which were caused by the pulse width modulation(PWM) methods applying in the BLDCM with trapezoidal back-EMF(electromotive force)waveform, were investigated in this work. A new PWM method, PWM_-ON_-PWM, was proposed. Compared with the conventional PWM methods, the ripple current caused by the diode freewheeling in the non-commutation zone can be eliminated, and so the torque ripples can also be decreased by the proposed PWM method. The simulation and experimental results are demonstrated to verify the validity of the proposed PWM method.
Study on switched reluctance motor using three-phase bridge inverter: Analysis and comparison with asymmetric bridge

Xü Liu,Zaiping Pan

2008-01-01

Abstract:This paper analysis the principle of two phases excitation and presents a method to control the speed of switched reluctance motor (SRM) which is driven by a three-phase bridge inverter. Until recently, SRMs are mainly driven by a unipolar asymmetric bridge inverter which has limited its wide applications because of its special structure which has increased the drive cost. However, if a bridge inverter is used in driving SRM, it will save drive cost for three-phase bridge inverter has been widely applied in IM, BLDC drivers. This paper extends phase-shifter control method under asymmetric bridge inverter to three-phase bridge inverter and proposes a novel method to operate SRM based on three-phase bridge inverter. Furthermore, a comparison between two phases excitation and conventional method is carried on to show the differences between phase current and electromagnetic torque. Finally simulation results are presented to verify the proposed control method.
Reduction of Commutation Torque Ripple in Brushless DC Motors

WANG Zheng-shi,ZHANG Zhao-li,CHEN Hui-ming

DOI: https://doi.org/10.3969/j.issn.1671-7848.2010.03.019

2010-01-01

Abstract:To reduce the influences of the commutation torque ripples in Brushless DC(BLDC),an optimal PWM method is proposed to analyze the PWM influences on the commutation torque ripples.Based on the principle and the BLDC motor equations,the mathematical derivation of the commutation torque ripples is given.To the main problem of torque ripples in brushless DC motor,a new PWM method(PWM-on)is proposed and proved to be efficient in reducing the torque ripple in theory.Based on the efficient TMS320LF28016 DSP control system,the experiment results show that the proposed method is efficient in reducing the torque ripple.
Comparative Performance Evaluation of Hall Effect Sensorless Control Options in Permanent Magnet Brushless DC Motor Drives

Kevin Lee,Feilang Li,Wenxi Yao

DOI: https://doi.org/10.1109/iemdc.2019.8785263

2019-01-01

Abstract:The objective of this paper is to present a comparative and quantitative study on three hall effect sensorless circuit configurations in permanent magnet (PM) brushless dc motor drives, along with four practical pulse width modulation (PWM) techniques. PM brushless direct current (BLDC) motor mathematical model, principles of operation, measurement circuit and logic configurations for three back electromotive force (EMF) zero crossing detection methods, as well as theoretical analysis on various PWM patterns are described. Their performance evaluation on waveform quality, rotor position tracking capability, and torque ripple impact are quantified as functions of motor speed and load variation. Digital time domain simulation models are established with the closed current and speed loops for the evaluation. Experimental results without using any hall effect sensors fully validate the theoretical and simulation findings.
A study about the control system of BLDCM

Yao Zhao,Huizhen Wang,Kang Chen,Lei Yao

2013-01-01

Abstract:Based on the three-bridge circuit, several control methods of BLDC are introduced. Six PWM chopped wave methods of three-phase six-beat control are analyzed and compared. Then the Direct Torque Control method of the BLDC is also presented, and the feature and principle of this method are analyzed. According to this traditional DTC method, this paper gives out a revised DTC method without the flux linkage observation. MATLAB is used to simulate this control method. An experiment research is also conducted based on an 850W BLDC control system, and the results are presented to validate the theory.
Drive of single-phase brushless DC motors based on torque analysis

Sun Lizhi,Feng Qi,Shang Jing

DOI: https://doi.org/10.1109/TMAG.2006.886965

IF: 1.848

2007-01-01

IEEE Transactions on Magnetics

Abstract:The high torque peaks commonly found in single-phase brushless dc motors can be compressed by different driving methods, which are proposed and studied based on finite-element analysis (FEA). It is concluded that one dead-zone can be added into the driving signals to improve current waveforms and torque envelope. The test results show that the noise level and performances are greatly improved when one proper dead zone is implemented. © 2006 IEEE.
Quantitative Characteristic Comparison Between Sensorless Six Step and Field Oriented Control Methods for Permanent Magnet Brushless DC Motors

Feilang Li,Wenxi Yao,Kevin Lee

DOI: https://doi.org/10.1109/ecce.2019.8912478

2019-01-01

Abstract:Permanent magnet (PM) brushless DC motors (BLDCM) have the advantages of high power density, high efficiency, simple structure and high reliability. BLDCM can be categorized into either trapezoidal back-electromotive (EMF) motor type, or sinusoidal back-EMF motor. There are typically two BLDCM control methods: One is six step control method which is easy to realize with simple hardware, the other is field oriented control (FOC) method which has better control performance. This paper compares quantitatively the characterization between these two BLDC control methods, with respect to torque ripple and power losses. Theoretical analysis and simulation studies are presented to illustrate their advantages and disadvantages. Experimental verification is conducted using a 48V, 4-pole, 4500RPM BLDC motor.
Drive of High-Voltage Single-Phase Brushless DC Motors Based on Torque Analysis

Lizhi Sun,Jing Shang,Jibin Zou

DOI: https://doi.org/10.1109/intmag.2005.1463481

2005-01-01

Abstract:In this paper, one high-voltage single-phase brushless motor with 4:4 pole structure is developed, and the drive is realized based on the analysis of the torque characteristics through field calculation.
Transient Analysis of a New Outer-Rotor Permanent-Magnet Brushless DC Drive Using Circuit-Field-torque Coupled Time-Stepping Finite-Element Method

Y Wang,KT Chau,CC Chan,JZ Jiang

DOI: https://doi.org/10.1109/20.996331

IF: 1.848

2002-01-01

IEEE Transactions on Magnetics

Abstract:In this paper, a new outer-rotor permanent magnet (PM) brushless DC drive is designed and analyzed. To enable this drive to be applied to electric vehicles, its transient performances at both normal and flux-weakening operations are particularly focused. The distinct feature in design is due to the new motor configuration including the outer-rotor topology, the multipole magnetic circuit and the full slot-pitch coil span arrangement. The distinct feature in analysis is due to the development of the circuit-field-torque coupled time-stepping finite-element method. The proposed PM brushless DC drive is prototyped. The analysis results are verified by experimental measurement.
A Fault-Tolerant Direct Torque Control Strategy for A Brushless Dc Motor Driven by A Single Sided Matrix Converter

J. Wang,X. Y. Huang,Y. T. Fang,Q. F. Lu,H. Yang,Y. Q. Gao

2016-01-01

Abstract:A fault-tolerant direct torque control (DTC) strategy for a brushless dc (BLDC) motor with a single sided matrix converter (SSMC) for an electrohydrostatic actuator system in aerospace application is proposed in this paper. The voltage is divided into seven levels, a torque hysteresis control is applied to each phase, voltage of different levels are provided to the motor to control the torque. A Matlab/Simulink model is built and the simulations are carried out. The results verify the fault-tolerant DTC control strategy under fault condition.
Analysis and simulation study on single-phase H-bridge rectifier/inverter

CHEN Xian-ming,LV Hong-shui,LIU Guo-hua

DOI: https://doi.org/10.3969/j.issn.1005-7277.2012.05.001

2012-01-01

Abstract:The detailed study has been paid for PWM control of single-phase H-bridge rectifier/inverter,which is able to implement double-direction energy flow.It also compares advantages and disadvantages between singlepole and double-pole PWM inverter.When H-bridge operates as a rectifier,power factor correction(PFC) function must be implemented.Namely,input sinusoidal current and power factor 1 in AC side of the rectifier is satisfied.Also when H-bridge operates as an inverter,output sinusoidal current and power factor 1(when connects to electric grid) is ensured.At last,the simulation of H-bridge operation under one cycle control(OCC) is completed with Matlab/Simulink software.It verifies the validity of H-bridge analysis and control with single-pole PWM better than that of double-pole PWM.
Analysis and Simulation on Commutation Torque Ripples of Six-Phase Brushless DC Motor

ZHANG Bo,HUO Long-chao

DOI: https://doi.org/10.3969/j.issn.1004-7018.2009.02.003

2009-01-01

Abstract:Compared with the triphase permanent magnet brushless DC motor (PMBLDCM),the six-phase (dual-three phase) PMBLDCM which has two set of winding spatially shifted by 30° electrical degrees with isolated neutral points has less commutation torque ripples in the process of commutating phase.The mathematical model of six-phase PMBLDCM was constructed in the paper,according to the commutation principle of BLDCM,the commutation torque ripples of six phase and triphase PMBLDCM were analyzed and compared,at the same time,it was derived that the commutation torque ripples of six-phase PMBLDCM was half of triphase PMBLDCM,and the simulation results proved the conclusion above.
Direct Torque Control for Brushless DC Motors in Aerospace Applications with Single Sided Matrix Converters with Reduced Torque Ripple

Jun Wang,Xiaoyan Huang,Shuofeng Zhao,Youtong Fang

DOI: https://doi.org/10.1109/iecon.2017.8216710

2017-01-01

Abstract:This paper proposes a direct torque control strategy for a brushless dc (BLDC) motor with a single sided matrix converter (SSMC) for an electrohydrostatic actuator system in aerospace application. A hybrid two- and three-phase switching mode is applied to minimize torque ripples during commutation. A six-phase SSMC is investigated and the simulation results are presented. Compared with current hysteresis control, instantaneous torque control and fast torque response can be achieved with reduced torque ripples.
Joint Simulation Analysis of Brushless Dc Motor and Control System

Yuanfeng Huang,Haifeng Wang,Wang Li

DOI: https://doi.org/10.1109/icems.2014.7013557

2014-01-01

Abstract:This paper studies 40kW brushless DC motor and its control system, establishes the integrative model and joint simulation model, and analyzes the stator current, back EMF, torque following characteristic and speeding response characteristic of the motor. Through the analysis of simulation results, the accuracy and reliability of the integrative simulation are verified. This paper provides a reference for the joint simulation analysis of brushless DC motor and control system.
Control Analysis of PM Brushless DC Motor Used in Flywheel Energy Storage System

Changsheng Zhu

2012-01-01

Abstract:Aiming at reducing the current and the torque ripple appeared in flywheel energy storage system running in wide-range speed,after the analysis of torque ripple in the commutation interval,the relation between the torque ripple and the speed was established.A hybrid method was presented that the PWM-on-PWM was chosen to control power devices during low-speed range,while during high-speed range,the overlapping commutation with PWM was used.The control method were evaluated on the effect of reducing the current and the torque ripple during the commutation interval,the Matlab/Simulink model was built,and the running test in low-speed range were tested.The experimental results show that the proposed method can eliminate diodes′ free-wheeling phenomenon and reduce the torque ripple during the commutation interval,it adapts for brushless DC motor in wide speed-range.
The Influence of PWM Modes on the Electromagnetic Torque of PM BLDCM

邱建琪,史涔溦,陈永校

DOI: https://doi.org/10.3969/j.issn.1009-5578.2003.12.007

2004-01-01

Abstract:The characteristic of different PWM modes for brushless DC motor is compared. The formulas of the phase current and electromangnetic torque are analyzed based on mathematic model of the BLDCM.The simulation results indicate that single-chop PWM method is more effective than the double-chop PWM method for the production of the electromagnetic torque.
Dynamic characteristics analysis of the brushless DC motor direct drive system

Gui-jie YANG,NLi SU,NLi-zhi SU,Yong-ping LU,Sh-hua GAO

DOI: https://doi.org/10.3969/j.issn.1007-449X.2000.01.001

2000-01-01

Abstract:The mathematical model of a brushless DC motor direct drive system with integral DSP motor controller ADMC 331M is deduced and a full digital vector control brushless DC mo-tor direct drive system is introduced in this paper.The influence of the leading angle (lagging angle) of the current reference signal the parameters and drive mode of the system to the dy-namic characteristics are anal yzed.The results of simulation and experiment indicate that the deterioration of the dynamic characteristics of the system is caused by leading angle(laggingangle)of the current reference signal.With the magnetic field orient control,the brushless DC motor system can obtain a maximum output torque and the best dynamic characteristics.When the gain of the current ratio regulator and enlargement factor of power inverter are in-creased,dynamic characteristics of the system will become better;when the compound drive mode of sine wave plus triple and quintuple harmonics is used,the dynamic characteristics of the system can be improved.
Symmetrical Dynamical Characteristic of Peak and Valley Current-Mode Controlled Single-Phase H-bridge Inverter

Liu Hong-Chen,Li Fei,Su Zhen-Xia,Sun Li-Shan

DOI: https://doi.org/10.1088/1674-1056/22/11/110501

2013-01-01

Chinese Physics B

Abstract:Complex dynamical phenomenon was studied in the single phase H-bridge inverter which was controlled by either a peak current or a valley current. The state functions and the discrete iterative map equations were established to analyze the dynamical phenomenon in the single phase H-bridge inverter. The dynamical characteristics of the single phase H-bridge inverter, such as time domain waveform diagram, bifurcation diagram, and folding map, were obtained by using the numerical calculation when the circuit parameters varied in specific range. Moreover, the simulation results were obtained by using the OrCAD-PSpice software to validate the numerical calculation. Both the numerical calculation and the circuit simulation show that the symmetrical dynamical phenomenon occurs in the single phase H-bridge inverter controlled by the peak current or the valley current.
A New BLDC Motor Drives Method Based on BUCK Converter for Torque Ripple Reduction

Zhang Xiaofeng,Lu Zhengyu

DOI: https://doi.org/10.1109/ipemc.2006.4778134

2006-01-01

Abstract:This paper presents a comprehensive analysis on torque ripples of brushless dc motor drives in conduction region and commutation region. A novel method for reducing the torque ripple in brushless dc motors with a single current sensor has been proposed by adding BUCK converter in the front of 3-phase inverter. In such drives, torque ripple suppression technique is theoretically effective in commutation region as well as conduction region. Effectiveness and feasibility of the proposed control method is verified through experiments

Analysis of Torque-Current Characteristic of Brushless DC Motor Driven by Three-Phase H-bridge

Steady Performance Analysis on Single-Phase Brushless DC Motor

Research on PWM Method in Brushless DC Motor

Study on switched reluctance motor using three-phase bridge inverter: Analysis and comparison with asymmetric bridge

Reduction of Commutation Torque Ripple in Brushless DC Motors

Comparative Performance Evaluation of Hall Effect Sensorless Control Options in Permanent Magnet Brushless DC Motor Drives

A study about the control system of BLDCM

Drive of single-phase brushless DC motors based on torque analysis

Quantitative Characteristic Comparison Between Sensorless Six Step and Field Oriented Control Methods for Permanent Magnet Brushless DC Motors

Drive of High-Voltage Single-Phase Brushless DC Motors Based on Torque Analysis

Transient Analysis of a New Outer-Rotor Permanent-Magnet Brushless DC Drive Using Circuit-Field-torque Coupled Time-Stepping Finite-Element Method

A Fault-Tolerant Direct Torque Control Strategy for A Brushless Dc Motor Driven by A Single Sided Matrix Converter

Analysis and simulation study on single-phase H-bridge rectifier/inverter

Analysis and Simulation on Commutation Torque Ripples of Six-Phase Brushless DC Motor

Direct Torque Control for Brushless DC Motors in Aerospace Applications with Single Sided Matrix Converters with Reduced Torque Ripple

Joint Simulation Analysis of Brushless Dc Motor and Control System

Control Analysis of PM Brushless DC Motor Used in Flywheel Energy Storage System

The Influence of PWM Modes on the Electromagnetic Torque of PM BLDCM

Dynamic characteristics analysis of the brushless DC motor direct drive system

Symmetrical Dynamical Characteristic of Peak and Valley Current-Mode Controlled Single-Phase H-bridge Inverter

A New BLDC Motor Drives Method Based on BUCK Converter for Torque Ripple Reduction