Motion Control System's Integration into Intranet with Distribution Technology

C Yuan,GH Er,Z Wang,JM Zhao

DOI: https://doi.org/10.1109/wcica.2000.863215

2000-01-01

Abstract:This thesis described the integration of the real-time motion control network with switch high-speed Ethernet technology and distributed database technology. An application is introduced at the end

What problem does this paper attempt to address?

Networked Control System Design and Implementation

JM Zhang,SQ Wang

DOI: https://doi.org/10.1109/icmlc.2002.1174479

2002-01-01

Abstract:At present, the distribution of a control system based on a network is a "hot" research subject in the field of process control. This paper designs and implements a network-based process control system, which possesses functions such as remote control, clock synchronization, and a friendly man-machine interface. Simulation results over a university campus network confirm that the network-based control system is feasible and effective.
Design of Motion Control System Based on EtherCAT

Kai XIE,Gang-feng YAN

DOI: https://doi.org/10.13462/j.cnki.mmtamt.2017.02.017

2017-01-01

Abstract:For the shortages of current multi-axis motion control system in synchronization and the control a-bility, a multi-axis motion control system based on EtherCAT is designed. The master station and slave sta-tion are constructed using real-time operating system. A solution of building embedded EtherCAT master is presented, which uses IgH EtherCAT Master open source components for RT-Linux, and Qt for GUI. The slave of this system is based on uC/OS-III operating system, which uses preemptive kernel to guarantee the real-time data among slaves. Thus, this system can ensure the synchronization among multi-axis. The results shows that, the multi-axis motion control system based on EtherCAT has a facilitate connection and the syn-chronization time is at microsecond level, which can meet the requirement of real-time and synchronization.
Research on networked control system based on Agent technology

Huang Hai,Zhang Ke,Zhang Jianming,Wang Shuqing

DOI: https://doi.org/10.19650/j.cnki.cjsi.2008.08.022

2008-01-01

Abstract:This paper demonstrates the relationship between networked control system and industrial IT,and proposes the idea of virtual loop in the control system design based on network data.An Agent based model design pattern of complex networked control system is established and the task scheduling problem is solved based on the contract net technology.The motion Ethernet control open platform is designed,which is a valuable experimental facility.
Study on monitoring approach of 3D scanning and measuring machine based on Internet/Intranet

Wenxiong Wang,Keqing Lu,Zichen Chen

2006-01-01

WSEAS TRANSACTIONS ON COMMUNICATIONS

Abstract:Combing with remote monitoring and control technology with production management ideas, a remote monitoring and management system and approach of 3D laser scanning machine based on intemet/intranet is presented in this paper. The operation model, system structure are studied and the theory to realize the system function is also given. With the net programming technology, the prototype system is successftilly developed, furthermore, the key techniques are discussed. Finally the effect of the system is testified.
EPA-based Open Network Control System

Dongqin Feng,Wenjun Huang,Jianxiang Jin,Jian Chu

DOI: https://doi.org/10.1109/icca.2003.1595168

2003-01-01

Abstract:The Ethernet is more and more used in the industrial environments. Because of the non-deterministic protocol of CSMA/CD, Ethernet is thought not to be suitable for the control of real time applications. With the worldwide application and development of Ethernet, its transmission rate is considered sufficiently high enough to estimate that all messages can be received inside a predefined temporal window. Especially, using Ethernet in industrial network will brings a lot of advantages: (1) consistency with the other communication systems installed in the enterprise; (2) employment of the same hardware all over the factory; (3) short cycle-times due to the high transmission speed; (4) large availability of chips implementing the MAC protocol, etc. In this paper, we first analyze the real-time capability of Ethernet and features of traffic for industrial network. Then, we propose some technologies for the design of an Ethernet-based real-time application. Finally, we present an EPA (Ethernet for Plant Automation)-based open network control system.
Research of measurement and control for bearing based on distributed system

钱少明,吴瑞明,徐志农,周晓军

DOI: https://doi.org/10.3969/j.issn.1001-2265.2004.02.032

2004-01-01

Abstract:The distributed automatic microbearing measuring system is introduced in this article, a three layers network is established by field-bus CAN and Ethernet based on TCP/IP protocol.The system consists of PC、IPC、PLC.This article also gives an account of the design of the multi -communition software.To irregular topology in distributed network,algorithm about communication path is discussed.
Design and Realization of Application Interface Between Real-Time Database and Industrial Process Control System

GAO Feng,WAN Li,LIU Yu-ming,WU Jun-qiang,WANG Xiao-yong,LIANG Jun,WANG Wen-qing,LIU Zhi-peng

DOI: https://doi.org/10.3969/j.issn.1671-7147.2007.01.002

2007-01-01

Abstract:For the application of real-time database in a petrochemical plant,the article put forwards to a new concept to resolve the communication among real-time database and DCS,control software,and Web-based user interface.The scheme is developed based on Windows 2000 Server using the technique of multe-threading,anolymous pipe and WinSock,etc.The results of long industrial running of this scheme show that it is more effective and feasible for industrial process.
Study on Networked Control for Power Electronic Systems

Yao Zhang,Hao Ma,Fei Xu

DOI: https://doi.org/10.1109/pesc.2007.4342096

2007-01-01

Abstract:This paper proposes a novel control strategy based on network for power electronics system. The definition of networked control is presented in control through network and control of network. According to the actual situation of power electronics, network selection and communication mechanism are presented. By means of the communication cell, standardized data stream of control loop and characteristics of network- induced delay through communication, some concepts of control through network is described. After the rough estimation of network-induced delay of all kinds of network during the transmission process for data of power electronics, the strategies of networked control for power electronic systems are presented by different MAC and topologies, which embody the essence of control of network.
Fuzzy Speed Control of Networked Motion Control Systems

Shangmin Zhang,Dezong Zhao,Chunwen Li,Richard Stobart

DOI: https://doi.org/10.1115/1.4029903

2015-01-01

Journal of Computational and Nonlinear Dynamics

Abstract:This paper proposed an integrated scheme for the modeling and control of induction motors in the networked environment. The networked control system (NCS) is built in hierarchical structure, which consists of a networked speed controller and a local controller. In the networked speed controller, fuzzy gain scheduling is applied to guarantee the robustness against communication constraints. Furthermore, a state predictor is designed to compensate the time delay occurred in data transmission from the sensor to the controller, as a component of the networked speed controller. Simulation and experimental results are given to illustrate the effectiveness of the proposed approach.
The Remote Fan Control Based on Real-Time Ethernet

XIE Mingwei,ZHU Rusong,GU Zhenghua

DOI: https://doi.org/10.3969/j.issn.1009-671x.2011.02.06

2011-01-01

Abstract:To overcome the bad real-time performance of remote control system usually used in industrial field,a method is given to implement remote control based on real-time Ethernet,which combines real-time Ethernet,virtual instrument and optic fiber transmission.The result of experiment indicates that the remote control system based on real-time Ethernet has high reliability,better real-time performance and stronger anti-jamming ability,compared with the common PLC remote control system.It has great value in the control of large industrial field.
Research on Motion Control Integration Technologies of CNC Based on Web Services

高荣,王治森,叶佩青

DOI: https://doi.org/10.3969/j.issn.1005-2402.2009.03.008

2009-01-01

Abstract:Motion control card is usually an important part of CNC system. Information integration of Web Services is essential; the key technologies of motion control card integration are studied. The unified interface for integration of motion control card and CNC is discussed. The concept of version space and the method to shorten the version space have been proposed. The application experiment of motion control card based on Web Services is accomplished. The result is helpful to motion control integration between CNC system and different platforms and reconstruction.
Development of a networked multi-agent system based on real-time ethernet

Xiong Xu,Zhenhua Xiong,Jianhua Wu,Xiangyang Zhu

DOI: https://doi.org/10.1007/978-3-642-25486-4_36

2011-01-01

Abstract:This paper proposes a networked multi-agent system based on the real-time Ethernet. The developed system consists of a set of smart networked agents, which are connected by a ring topology through the real-time Ethernet. Each networked agent is designed to realize motion control tasks and real-time communication capabilities using digital signal processor and field-programmable gate array technologies. Furthermore, a real-time communication protocol is proposed to cope with the non-deterministic problem of Ethernet. Then, time delays caused by data processing and message transmission are analyzed. A platform is built to evaluate the capabilities of the developed networked multi-agent system. The experimental results demonstrate that the presented system achieves good performance in terms of real-time communication and servo-control performance.
Design of a Distributed Multiaxis Motion Control System Using the IEEE-1394 Bus

Limin Zhu,Guoying Gu,H. Ding,Z. Xiong

DOI: https://doi.org/10.1109/TIE.2010.2044127

2010-03-01

Abstract:This paper presents a distributed multiaxis motion control system based on the IEEE-1394 bus. In the system design, the Unified Modeling Language is employed to illustrate interactions of the objects required in the system. The developed system consists of a set of smart distributed control nodes connected one by one through the IEEE-1394 bus. Each smart node contains four modules, i.e., an IEEE-1394 interface module, a digital signal processor module, a field-programmable gate array module, and a digital-to-analog converter module. It accomplishes its own control task and coordinates with the others through information exchanges, sampling sensor signals, and controlling actuators. A scheduled communication protocol is proposed according to the criteria in terms of bounded time delay and guaranteed transmission. Time delays arising from data processing and message transmission are analyzed. A platform is built, and experiments are conducted to demonstrate the capabilities of the developed distributed control system for real-time communication and synchronous tracking control, which are required for multiaxis applications. The results verify the feasible application of the IEEE-1394 bus to distributed motion control.

Computer Science,Engineering
Research on technology of product data exchange for internet-based distributed integrated manufacturing system

Peng Gao,Lanfen Lin,Jinxiang Dong,Ming Cai

DOI: https://doi.org/10.1109/CSCWD.2002.1047726

2002-01-01

Abstract:One of the key technologies for distributed integrated manufacturing systems is to realize automatic transmission and conversion of product data among distributed and heterogeneous systems like CAD, CAPP, CAM, CAE, etc. This paper presents an Internet-based framework of product data exchange and the architecture of the framework, which uses Internet/CORBA as the communication platform and XML as product data exchange language. This framework within which, conversion of other data formats to XML format is implemented by software agents, supports exchange of structured and non-structured product data.
The Ethernet's Applying in the Motor Controlling System

Xian-wei MA,Jun-hua MA

DOI: https://doi.org/10.3969/j.issn.1005-2895.2006.03.030

2006-01-01

Abstract:This paper discusses the characteristics of the Ethernet and the TCP/IP protocol,and analyses the braw foreground of its applying in the industrial control system.And it also supplies an idiographic project of its applying.
Technologies And Solutions To Integrate Control Networks With Data Networks

Tieming Liu,Timo R. Nyberg,Gang Xiong,Judong Shen,Yushun Fan

2000-01-01

Abstract:Automation systems have developed into a control network age, and the integration of control networks with data networks ran provide great benefits to enterprise automation systems. In this paper, first the benefits to integrate these two networks are represented. Then the hey technologies to integrate control networks with data networks, CORBA, OLE for Process Control, are discussed and compared. Also other technologies, such as ODBC/JDBC, ASP and Active X, are discussed. Finally, the solution to integrate control networks with data networks are given out.
Design and Implementation of High-Speed Real-Time Communication Architecture for PC-Based Motion Control System.

Jian Hu,Hui Wang,Chao Liu,Jianhua Wu,Zhenhua Xiong

DOI: https://doi.org/10.1007/978-3-319-13963-0_41

2014-01-01

Abstract:To enhance the efficiency and stability of real-time data acquisition and transmission in motion control process, a high-speed real-time communication architecture based on FPGA and DSP is developed in this paper. The direct-memory-access (DMA) control module initiates DMA transfers over the peripheral-component-interconnect (PCI) bus. After that, two first-in-first-out (FIFO) buffers work as caches and convert data widths between the PCI bus and the local bus. Consequently, the data caches can be accessed by DSP over the local bus under DMA mode. The size of data transferred each time is able to be adjusted according to the application requirements. Experiments are carried out to demonstrate that the proposed communication architecture is capable of achieving high speed and stability in data communication with low consumption of compute resources.
The Control of a Beamline Over Intranet

X. J. Yu,Q. P. Wang,P. S. Xu,X.J. Yu,P.S. Xu

DOI: https://doi.org/10.48550/arXiv.cs/0111008

2001-11-06

Networking and Internet Architecture

Abstract:The machines and beamlines controlled by VME industrial networks are very popular in accelerator faculties. Recently new software technology, among of which are Internet/Intranet application, Java language, and distributed calculating environment, changes the control manner rapidly. A program based on DCOM is composed to control of a variable included angle spherical grating monochromator beamline at National Synchrotron Radiation Laboratory (NSRL) in China. The control computer with a residential DCOM program is connected to Intranet by LAN, over which the user-end-operating program located in another computer sends driving beamline units' commands to the control computer. And also a web page coded in Java, published by the WWW service running in the control computer, is simply illustrated how to use web browser to query the states of or to control the beamline units.
An FPGA-Based Real-Time Solution for Networked Motion Control Systems

Maoqing Ding,Xiong Xu,Yonghua Yan,Zhenhua Xiong

DOI: https://doi.org/10.1007/978-3-642-33515-0_57

2012-01-01

Abstract:In order to solve the problem of real-time communication for multi-axis in networked motion control systems(NMCSs), a field-programmable gate array (FPGA) based real-time solution is proposed. In the proposed solution, a hardware data processing strategy is designed and the data link layer of real-time communication is implemented on FPGA. Moreover, in order to decrease the forwarding delay, the forwarding of real-time communication data is shifted down to data link layer from application layer. Theoretical analysis and experimental results show that the FPGA-based real-time solution reduces jitter and delay of communication. After 20000 tests, each nodes delay is 1.180 μs in average, which achieves the same real-time performance as EtherCAT.
Research and Development on Full Distribution CNC System

Z. Y. Chen,W. Guo,C. X. Li

DOI: https://doi.org/10.1109/iciea.2006.257098

2006-01-01

Abstract:The CNC architecture by expanding different motion cards is popular now, but it still lacks good configurable performance, the most functions of the motion card are redundant, and the control requirements cannot be met on the complex and high-precision situations. In this paper, a new full distribution CNC (FDCNC) system is presented. In this structure, the former two-grade interpolation is replaced with offline interpolation method; the motion control card in IPC is displaced with several intelligent nodes embedded in servo controllers. Communication between IPC and servo controllers is through CAN, which can transmit a lot of data in two directions and its communication protocol is public and standard. Thus, it gets much easier to repair, reconfigure, and replace some components. Additionally, enough information does great good to watching and diagnosing. Due to the use of Windows NT+RTX, not only developers are able to take advantage of the abundant Windows resources, but also CNC system possesses friendly graphic user interface (GUI), excellent open performance and good real-time performance. At last a running case is given

Motion Control System's Integration into Intranet with Distribution Technology

Networked Control System Design and Implementation

Design of Motion Control System Based on EtherCAT

Research on networked control system based on Agent technology

Study on monitoring approach of 3D scanning and measuring machine based on Internet/Intranet

EPA-based Open Network Control System

Research of measurement and control for bearing based on distributed system

Design and Realization of Application Interface Between Real-Time Database and Industrial Process Control System

Study on Networked Control for Power Electronic Systems

Fuzzy Speed Control of Networked Motion Control Systems

The Remote Fan Control Based on Real-Time Ethernet

Research on Motion Control Integration Technologies of CNC Based on Web Services

Development of a networked multi-agent system based on real-time ethernet

Design of a Distributed Multiaxis Motion Control System Using the IEEE-1394 Bus

Research on technology of product data exchange for internet-based distributed integrated manufacturing system

The Ethernet's Applying in the Motor Controlling System

Technologies And Solutions To Integrate Control Networks With Data Networks

Design and Implementation of High-Speed Real-Time Communication Architecture for PC-Based Motion Control System.

The Control of a Beamline Over Intranet

An FPGA-Based Real-Time Solution for Networked Motion Control Systems

Research and Development on Full Distribution CNC System