Abstract:Hybrid calcium carbonate particles, synthesized III the presence of block copolymer polystyrene-b-poly(acrylic acid) (PS-b-PAA), were used to fabricate polyelectrolyte (PE) such as polylallyamine hydrochloride)/ poly(strene sulfonate sodium) (PAH/PSS) and poly (diallyldimethyl ammonium chloride)/poly (styrene sulforate sodium) (PADH/PSS) Capsules, by layer-by-layer (LbL) technique. Novel micelle-enhanced polyelectrolyte (PE capsules were thus obtained. The structure of the micelle-enhanced PE microcapsules was studied in this article. Due to the presence of a large amount of negatively charged micelles inside PE capsule interior, which were liberated from templates, the capsule wall was tightly re-constructed. Different from the wall properties of the conventional PE capsules, the wall of the micelle-enhanced PE capsules showed stability under an extensive pH range from I to 14, but the micelled enhanced capsules showed dented morphology in solutions with high NaCl concentration such as 0.5 mol/L and I mol/L. The state of the block copolymer in the capsules was investigated in dialysis bag by simulating the Solution condition of the capsule interior after the template being removed. It was found that the micelle size of the block copolymer In solution of templates dissolution was tens of nanometers after the solution was dialyzed for 24 h. With the dialysis time increasing up to at least 72 It, the block copolymer began to precipitate onto the dialysis bag from the solution The interaction between the 2-D polyelectrolyte multilayer film and micelles formed by block copolymer in templates solution was studied by UV-Vis measurements as well. It was found that PE multilayer could interact with micelles via electrostatic force. At the same time I the block copolymer remained in the capsules interior could be precipitated onto the PE multilayer via dialyzing in deionized water for a long time (pH similar to 6). A micelle-related layer was formed which was stabilized by the "bridge effect" of calcium ions. That is, the wall of the micelle-enhanced PE capsules had a bilayer structure and was formed by the polyelectrolyte multilayer and micelle-related layer. It seemed that the two layers with different properties clung to each other via electrostatic force. The formation mechanism of the bilayer structure was well illuminated oil the aforementioned studies. This is a key property of the micelle-enhanced PE capsules with which all the properties of the capsules were linked. Based on the bilayer structure of the capsules, the morphology changes of the capsules in solutions with different conditions such as high NaCl concentrations could be elucidated well. However, more direct proofs and further studies were needed to completely resolve the fine structure of the micelle-enhanced PE capsules.

Surface Texture of Poly(styrenesulfonate Sodium Salt) and Poly(diallyldimethylammonium Chloride) Micron-Sized Multilayer Capsules: A Scanning Force and Confocal Microscopy Study

Preparation and Characterization of NaCS–CMC/PDMDAAC Capsules

Preparation of "micelles enhanced " polyelectrolyte capsules

Stability and Mechanical Properties of Polyelectrolyte Capsules Obtained by Stepwise Assembly of Poly(styrenesulfonate Sodium Salt) and Poly(diallyldimethyl Ammonium) Chloride Onto Melamine Resin Particles

The Tough Microcapsules Of Acrylic Acid-Styrene-Isoprene-Styrene Quadrablock Copolymer Shell Via Pickering Emulsion Technique

A Facile Route to Synthesize Highly Uniform Nanocapsules: Use of Amphiphilic Poly(acrylic Acid)‐block‐polystyrene RAFT Agents to Interfacially Confine Miniemulsion Polymerization

Structure Studies of Micelle-Enhanced Polyelectrolyte Microcapsules

Swelling and Shrinking of Polyelectrolyte Microcapsules in Response to Changes in Temperature and Ionic Strength

A Study of Properties of "Micelle-Enhanced" Polyelectrolyte Capsules: Structure, Encapsulation and in Vitro Release

From the 2-Dimensional Unstable Polyelectrolyte Multilayer to the 3-Dimensional Stable Dry Polyelectrolyte Capsules

Multilayer Capsules with Cell-like Topology: Fabrication and Spontaneous Loading of Various Substances in Aqueous and Ethanol Solutions

A Facile Pathway to Fabricate Microcapsules by in Situ Polyelectrolyte Coacervation on Poly(styrene Sulfonate)-Doped CaCO3particles

Synthesis of Size-Controlled Acid-Resistant Hybrid Calcium Carbonate Microparticles As Templates for Fabricating “Micelles-Enhanced” Polyelectrolyte Capsules by the LBL Technique

Stable Microcapsules Assembled Stepwise from Weak Polyelectrolytes Followed by Thermal Crosslinking

Layer-By-Layer Self-Assembly of Polyelectrolyte and Low Molecular Weight Species into Capsules

Hollow Microcapsules with A Complex Polyelectrolyte Shell Structure Fabricated by Polymerization of 4-Vinylpyridine in the Presence of Poly(Sodium 4-Styrenesulfonate) and Silica Particles

3-Dimensional Stable Polyelectrolyte Hollow Capsules: Preparation and Spontaneous Encapsulation

Preparation of microcapsules with multi-layers structure stabilized by chitosan and sodium dodecyl sulfate

Preparation and embedding-releasing behavior of polyelectrolyte microcapsule

POLYELECTROLYTE MICROCAPSULES FABRICATED <I>VIA in situ</I> COACERVATION — THE INFLUENCE OF DOPED POLYELECTROLYTE AMOUNT IN THE TEMPLATES ON THEIR STRUCTURES AND PROPERTIES

Nanoengineering of Polymeric Capsules with A Shell-In-Shell Structure