Abstract:Freeze casting has been widely used in the preparation of nacre-inspired composites because of its prominent advantages in controlling the fine structure of ceramic scaffolds. However, the ceramic-phase content in composites prepared by this method is much lower than that in nacre due to the limitations of the dispersion and viscosity of the ceramic slurry. In this work, we combined the ideas of freeze casting and in-situ reaction to prepare nacre-inspired lamellar composites with high hard-phase contents. We first prepared the TiO2- - SiO2 porous scaffold with an initial solid loading of 20 vol% via unidirectional freeze casting and then infiltrated it with a 6061Al alloy. During the reaction process, the TiO2-SiO2 layers were progressively transformed into Al2O3 layers, and the Al layers were transformed into Al3Ti. Composites with different hard-phase volume fractions (approx. 29%, 38%, 52% and 65%) and different interfacial bonding strengths could be obtained by altering the infiltration temperature. Increases in the hard-phase content and the interfacial bonding strength substantially enhanced the bending and compressive strengths of the composites, with maximum values of 350 MPa and 854 MPa, respectively, achieved in the composites with approx. 65 vol% hard phases. However, the highest fracture toughness of 42.9 MPa m(1/2) and maximum fracture work of 3.6 kJ/m(2) appeared when the hard-phase content in the composite was approx. 38 vol%, sharing an appropriate interfacial bonding strength. A robust interface favors stress transfer but impedes crack deflection, while a weak interface fails to bear loads, even though it is conducive to crack deflection. A moderately-strong interface together with a considerable amount of layered soft phase contributes to the generation of multiple-cracking, and thereby greatly toughens the metal - ceramic composite.

On the preparation of metallic-matrix composites enhanced by interpenetrating phase through squeeze casting

The Making of Metal-Matrix Interpenetrating Phase Composites by Squeeze Casting

Metal-matrix Interpenetrating Phasecomposites Produced by Squeeze Casting

The Fabrication and Properties of the Squeeze-Cast TiN/Al Composites

Preparation, Characterization and Designing of Porous Ti–6Al–4V Through Metal Injection Molding Without Space Holder

Preparation of Ti/Al based nanophase composite powder by mechanical alloying

Preparation of Porous SiC Reinforced Metal Matrix Composites

Preparation of Intermetallic Compound Matrix Composites by Reaction Squeeze Casting

Solidifying structures of Al2O3 short fiber/Al-Si alloy matrix composite prepared by squeeze casting

Lamellar and Interpenetrated Al/(Al2O3–TiC) Composites Prepared by Bidirectional Freeze Casting and Melt Infiltration

A Novel Approach to the Fabrication of Lamellar Al2O3/6061Al Composites with High-Volume Fractions of Hard Phases

Squeeze-Exhaust Casting of Al<sub>2</sub>O<sub>3p</sub>/6061 Composites Material with High Densification and Strength

Study on squeeze casting of an in situ 5 vol.-% TiB2/2014 Al composite

A Novel Approach to Fabricate Ceramic/metal Interpenetrating Phase Composites by Ultrasonic-Assisted Spontaneous Infiltration

Preparation of Particles Reinforced Aluminum Matrix Composites by In-Situ Synthesized Al-Ti Intermetallics

Preparation and Interface Investigation of Fe/Al2o3p Composite Activated by Ni and Ti

(SiC p +Ti)/7075Al hybrid composites with high strength and large plasticity fabricated by squeeze casting

Preparation and Interface Structure of CTCp/Cr26 Composites with the Pinning Effect

Microstructure, Properties and Strengthening Mechanism of Cu-Tib2-Al2o3 Composite Prepared by Liquid Phase In-Situ Reaction Casting

Sicp/Al Composites Fabricated by Modified Squeeze Casting Technique

Microstructure, properties and reaction kinetics of a Cu–Al2O3–TiB2 alloy prepared by a new liquid phase in-situ reaction technology