Abstract:Dendrite growth velocity as a function of initial bulk undercooling was systematically studied in situ using high speed thermal imaging of highly undercooled Ni90Cu10 and Ni95Cu5 single phase alloy melts. For these two non-dilute concentrated alloys, the dendrite growth velocity first increased continuously at small and mediate undercooling regimes and then discontinuously to a maximum value at the high undercooling range. A clear plateau appeared in the growth velocity-undercooling curve revealed a gradual transition from mainly solute-controlled growth to mainly thermal-controlled growth, which was very similar to the solidification characteristics of a dilute alloy. The discontinuity appeared in the growth velocity-undercooling relationship was suggested to be induced by the finite solute diffusion speed in the bulk melt ahead of the advancing solid-liquid interface. Microstructure, substructure and microtexture of the two undercooled alloys were characterized using EBSD technique, and the fundamental mechanism behind “spontaneous grain refinement” is elucidated. The microstructure evolution indicated two kinds of grain refinements: one was dendrite remelting induced grain refinement and the other was recrystallization induced grain refinement. It was found that the texture of the as-solidified microstructure was getting more and more random as the initial bulk undercooling increased, which was due to the increased stress and recrystallization in the as-solidified microstructure. New evidence of grain refinement was found in the as-solidified samples. We found that the samples undercooled beyond the critical undercooling had a grain refined microstructure and that this corresponded with a clear discontinuity in the dendrite growth velocity-undercooling curve. Microstructural data suggested that in Ni-Cu alloys grain refinement at a high undercooling was a consequence of a recrystallization process, which contrasted with conventional grain refined alloys where grain refinement appeared to be the result of remelting-induced dendritic fragmentation.

Microstructure evolution of super-cooled Cu-Ni-Fe alloy

Solidification Microstructure in a Supercooled Binary Alloy

Microstructure Refinement Mechanism of Undercooled Cu55Ni45 Alloys

Rapid Solidification Structure Refinement Mechanism in Highly Undercooled Cu Based Ternary Alloys

Influence of Cooling Rate on the Formation of Bimodal Microstructures in Nickel-Base Superalloys During Continuous Two-Step Aging

Effect of Minor Addition of Co on Nonequilibrium Solidification of Deeply Undercooled Cu Based Alloys

Solidification Microstructure Evolution and Grain Refinement Mechanism under High Undercooling of Undercooled Ni90Cu10 Alloys

Microstructure Transformation of Undercooled Cu-Ni-Co Alloy and Refinement Mechanism under High Undercooling

Observation of Dendrite Growth Velocity and Microstructure Transition in Highly Undercooled Single Phase Alloys

Grain Refinement Mechanism at High Undercooling of Ni80Cu20 Alloy

Microstructure refinement mechanism upon deeply undercooled solidification of a Ni88Cu6Co6 alloy

Growth Velocity-Undercooling Relationship and Structure Refinement Mechanism of Undercooled Ni-Cu Alloys

Forming mechánism of refined granular crystalline of Cu70Ni30 alloy by undercooled solidification

Investigation on nonequilibrium crystallization of highly undercooled Cu–Ni–Co alloys

Investigation on solidification structure evolution of deeply undercooled single-phase Ni-Cu-Co alloys

Non-equilibrium solidification of bulk undercooled Ni–P eutectic alloys

Solidification Structure Evolution and Grain Refinement Mechanism of a Deeply Undercooled Ni65Cu35 Alloy

Effect of Co Addition on Solidification Velocity, Hardness and Refined Structure Transformation Mechanisms of Undercooled Ni-Cu-Co Alloys

The Microstructure Evolution of a Fe-Ni-P-B Soft Magnetic Alloy Solidified at Different Undercooling

Co effect on rapid solidification microstructure transition of highly undercooled copper alloys

Microstructure and Hardness Evolution During Isothermal Process at 700 °C for Fe–24Mn–0.7Si–1.0Al TWIP Steel