Abstract:In this work, the most efficient and common engineered surface treatments identified as shot peening (SP), laser shock peening (LSP) and ultrasonic surface rolling process (USRP) were utilized to impact the 300 M ultrahigh strength steel. The microstructure evolution and surface strengthening behavior were carefully characterized and compared for the 300 M steel with various treatments. Besides, the underlying mechanisms for difference in grain refinement and surface mechanical properties by the arranged surface modification are revealed. The results indicate that a gradient structure with nano-grains at the top surface appears on the SP, LSP and USRP treated samples. The process of repeated impacts of SP in different directions leads to activation of multiple slip systems, which thus causes severe refined grains and dense dislocation activities associated with dislocation tangles, dislocation walls and blocking. A great variety of strikes per unit area by USRP results in higher plastic deformation compared to SP where numerous dislocation cells and deformation bands were generated. In contrast to SP and USRP, fewer slip systems are activated in LSP due to the short duration time which thus leads to the thinnest refined grain layer and more planar dislocation structures. The combination of low plastic work and lack of refined grains leads to lowest full width at half maximum (FWHM) in case of LSP samples whereas high FWHM comes from both fine grain size and dislocations in SP. The grain refinement and plastic work contributes to an increase of microhardness and compressive residual stress for the SP, LSP and USRP samples. To be clear, SP leads to a higher magnitude of hardness and compressive residual stress on the topmost surface while LSP causes a larger depth due to that shock wave in LSP influences material to much greater depth. Besides, the decomposition and redistribution of carbides are also noticed on the surface layer after the surface treatments with very high strain rate where numerous dislocations accumulate at the border of the carbides and slip trace is also observed within the carbides.

Stress corrosion cracking behavior and mechanism of coated ultra-high strength steel 300 M

Investigation of stress corrosion cracking behavior and mechanism analysis of a 1900 MPa-grade ultra-high-strength stainless steel

STRESS CORROSION CRACKING BEHAVIOR OF A NEW KIND OF ULTRAHIGH STRENGTH STEEL Cr12Ni4Mo2Co14 IN ACID ENVIRONMENT

CORROSION BEHAVIOR OF SUPER-AUSTENITIC STAINLESS STEEL AL-6XN IN SUPERCRITICAL WATER

Experimental Investigation of Stress Corrosion Characteristics for 16mnr Steel in Nitrate Solution

Effect of Heat Treatment on the Stress Corrosion Cracking Behavior of Cast Mg-3Nd-3Gd-0.2Zn-0.5Zr Alloy in a 3.5 Wt% NaCl Salt Spray Environment

Stress corrosion cracking of TC4 ELI alloy with different microstructure in 3.5% NaCl solution

Effect of Organizational Evolution on the Stress Corrosion Cracking of the Cr-Co-Ni-Mo Series of Ultra-High Strength Stainless Steel

Microstructure evolution and surface strengthening behavior of 300 M ultrahigh strength steel under engineered surface treatments

Corrosion of high-strength steel in 3.5% NaCl solution under hydrostatic pressure: Initial corrosion with tensile stress coupling

Effects of Cl- Concentration on Stress Corrosion Cracking Behaviors of Super 13cr Tubing Steels

Stress corrosion cracking behavior and mechanism of Fe-Mn-Al-C-Ni high specific strength steel in the marine atmospheric environment

Influence of Phase Dissolution and Hydrogen Absorption on the Stress Corrosion Cracking Behavior of Mg-7%Gd-5%Y-1%Nd-0.5%Zr Alloy in 3.5 Wt.% NaCl Solution

Corrosion of high-strength steel in 3.5% NaCl solution under hydrostatic pressure: understanding electrochemical corrosion with tensile stress coupling

Effect of Cl− Concentration on the SCC Behavior of 13cr Stainless Steel in High-Pressure CO2 Environment

The Localized Corrosion and Stress Corrosion Cracking of a 6005A-T6 Extrusion Profile

Stress Corrosion Cracking Behavior of Cold-Drawn 316 Austenitic Stainless Steels in Simulated Pwr Environment

Effect of Ultrasonic Impact Treatment on the Stress Corrosion Cracking of 304 Stainless Steel Welded Joints

Effect of Heat Treatment on Crevice Corrosion Behavior of 304 Stainless Steel Clad Plate in Seawater Environment

Effects of Surface State and Applied Stress on Stress Corrosion Cracking of Alloy 690TT in Lead-containing Caustic Solution

A Primary Study of the Effect of Hydrostatic Pressure on Stress Corrosion Cracking of Ti-6Al-4V Alloy in 3.5% NaCl Solution