Effect of CaO on the thermal expansion of Ca0.5Zr2 (PO4)3

Yuqing Chen,Gaorong Han,Zhijian Shen,ZiShang Ding

1998-01-01

Abstract:Influence of CaO on axial thermal expansion characteristics and thermal expansion coefficient of Ca0.5Zr2 (PO4)3 (CZP) was studied. The Ca2+ ions coming into lattice of CZP result in the thermal expansion anisotropy of CZP by the dilatometry linear increases with the increase of CaO content.

What problem does this paper attempt to address?

Anisotropic Chemical Expansion Of La1-Xsrxcoo3-Delta

Xinzhi Chen,Tor Grande

DOI: https://doi.org/10.1021/cm304040p

IF: 10.508

2013-01-01

Chemistry of Materials

Abstract:The crystal structure and the thermal and chemical expansion of rhombohedral La1-xSrxCoO3-delta (x = 0.3, 0.4) perovslcite were investigated by in situ high-temperature X-ray diffraction in pure oxygen and nitrogen atmospheres. The crystal structure was confirmed to change from rhombohedral (R (3) over barc) to cubic symmetry (Pm (3) over barm) with increasing temperature due to a second-order ferroelastic to paraelastic phase transition. The rhombohedral distortion at low temperature causes crystallographic anisotropy, and anisotropic thermal expansion, caused by rectification of the antiferrodistortive tilting and a minor decompression of the CoO6/2 octahedra is reported. The onset of chemical expansion due to reduction of the oxidation state of Co was observed below the phase transition temperature, which enabled investigation of the crystallographic anisotropy of the chemical expansion. The chemical expansion was significantly larger along the c-axis relative to the a-axis, demonstrating the strong damping of the octahedral tilting with increasing oxygen vacancies induced by the thermal reduction of Co. This phenomenon caused a strong depletion of the ferroelastic phase transition temperature with decreasing partial pressure of oxygen.
Effect of CaO Content on Properities of 3-1 Type Porous Lead Zirconate Titanate Ceramics

Jun Xu

2014-01-01

Abstract:By the special chelating properties of sodium alginate and CaCl2,the 3-1 type porous PZT ceramic with 85% porosity and 200 μm characterized by highly ordered and unidirectional oriented pores in the micrometer was made with a 10wt% solid loading. In this paper,we studied the influence of CaO content on the electrical properities and vickers hardness of porous PZT ceramics. When the CaO content was 0. 62wt%,the d33and e reached 120 and 820 respectively,which was 84% and 51% greater than that of the 2. 02wt% CaO content porous PZT ceramics. With the increase of CaO content the vickers hardness of the porous PZT ceramic magnified significantly and reached the peak( 0. 98 GPa) when the CaO content was 2wt%.
The effect of BaO addition on the sintering properties and grain growth behavior of CaZrO3 ceramics

Huan Xu,Wangnian Zhang,Mengxian Zhang,Ming Cao,Xitang Wang

DOI: https://doi.org/10.1007/s41779-024-01091-x

2024-09-30

Journal of the Australian Ceramic Society

Abstract:In the present work, dense CaZrO 3 ceramics were prepared by a conventional solid-state reaction using high-purity commercial ZrO 2 and Ca(OH) 2 as raw materials, and BaO as a sintering aid. The effect of BaO addition on the sinterability, phase composition, and microstructures of CaZrO 3 ceramics was investigated. The grain growth kinetics was also analyzed based on the classical Brook model. The results showed that an appropriate amount of BaO addition has a significant positive contribution to the densification and grain growth of CaZrO 3 ceramics. However, excess addition gives rise to the formation of BaZrO 3 at the grain boundary, which dramatically hinders the grain growth and thus degrades the sinterability of CaZrO 3 ceramics. The enhanced sintering mechanism is related to lattice distortion generated from the substitution of Ca 2+ sites by larger Ba 2+ ions. The grain growth kinetics analysis demonstrated that the grain growth activation energy is affected by the BaO addition, and the value is decreased from 65.5 to 55.4 kJ·mol −1 as the BaO content increases from 0 to 1 wt%.

materials science, ceramics
Effects Of Catio(3)On Microstructures And Properties Of (1-X) Znal2o4-Xmg(2) Tio4 (X=0.1) Microwave Dielectric Ceramics

Lei Wen,Lue Wen-Zhong,Wang Xiao-Chuan,Liang Jun,Jiang Jian-Jun

DOI: https://doi.org/10.3724/SP.J.1077.2009.00957

IF: 1.292

2009-01-01

Journal of Inorganic Materials

Abstract:ZnAl2O4-Mg2TiO4-CaTiO3 ceramics were prepared by the solid-state reaction. The effects of CaTiO3 on phase compositions, microstructure and microwave dielectric properties were investigated. It shows that CaTiO3 can effectively improve the sinterability of the ceramics and lower the densification temperature by about 150 degrees C. ZnAl2O4-based spinel, CaTiO3, MgTi2O5 and Zn2Ti3O8 phases are included in the ZnA(2)O(4)-Mg2TiO4-CaTiO3 system, however, Zn2Ti3O8 phase disappears when the sintering temperature is higher than 1400 degrees C. As CaTiO3 content increases, CaTiO3 phase in the sintered body raises while MgTi2O5 phase reduces. Furthermore, CaTiO3 can adjust obviously the temperature coefficient of resonant frequency of the (1-x)ZnAl2O4-xMg(2)TiO(4)(x = 0.21) ceramics. When 6mol% CaTiO3 is added to the (1-x)ZnAl2O4--xMg(2)TiO(4) (x = 0.21) system, a temperature-stable microwave dielectric ceramics sintered at 1400 degrees C with an epsilon(r) of 11.8, a Q center dot f of 88080GHz and a tau(f) of - 7.8 x 10(-6)/degrees C can be obtained.
Effect of Vacancy on Thermal Expansion Coefficient of Sm2Zr2O7 Ceramic

Xu Qiang,Wang Fuchi,Zhu Shizhen,Zhang Hongsong,Liu Ling,Wan Chunlei,Qu Zhixue,Pan Wei

DOI: https://doi.org/10.3321/j.issn:1002-185x.2007.z2.155

2007-01-01

Rare Metal Materials and Engineering

Abstract:M0.1Sm1.9Zr2O6.95 ceramics were synthesized by solid phase reaction using ZrO2 powder, Sm2O3 powder and bivalent MO powder (M=Mg, Ca) as starting materials. The compacts made from the mixed powders were sintered into bulks at the temperature of 1600 degrees C for 10 hours in air. The phases of the synthesized bulks were identified by X-ray diffraction (XRD) and the microstructure of the bulks was examined by SEM. The thermal expansion coefficients of the bulks were measured by thermal dilatometer. The results show that M0.1Sm1.9Zr2O6.95 ceramics with single phase and uniform microstructure were prepared successfully. The thermal expansion coefficient of M(0.1)Sm(1.9)qZr(2)O(6.95) ceramic is higher than that of pure Sm2Zr2O7 ceramic due to the introduction of vacancy. The improvement of the thermal expansion coefficient of the ceramic material for thermal barrier coatings is beneficial to the increasing of the service life of coatings.
Effect of Mass Fraction of CeO2 on Structure of Zirconolite-based Glass-ceramics

Chen Xiaomou,Meng Cheng,Zhang Feng,Tang Can,Ding Xingeng

2016-01-01

Rare Metal Materials and Engineering

Abstract:The structure and microstructure of zirconolite-based glass-ceramics were characterized by XRD and SEM, respectively. The normalized release rate of Ce (NRCe) was measured by the ASTM Product Consistency Test (PCT) leaching method. Results show that when CeO2 content is ranged from 0wt% to 1wt%, two zirconolite crystals, monoclinic (CaZrTi2O7-2M) and hexagonal layered structure (CaZrTi2O7-2T), form in the bulk glass. When the content of CeO2 increases from 3 wt% to 11 wt%, the monoclinic layered structure phase disappears. The unit cell parameters and cell volume V of zirconolite phase (CaZrTi2O7-2T) increase with the increase of CeO2 content. The leaching resistance shows that the solidified radioactive waste forms would be stable for the eventual geological disposal, and leaching rate of Ce3+ reaches 10(-7) g.m(-2).d(-1) at 28 d.
Thermal Expansion of SrZrO3 and BaZrO3 Perovskites

Yusheng Zhao,Donald J. Weidner

DOI: https://doi.org/10.1007/bf00200187

IF: 1.748

1991-01-01

Physics and Chemistry of Minerals

Abstract:High-temperature X-ray diffraction studies of SrZrO3 and BaZrO3 perovskites have been carried out to 1200° C. The diffraction patterns are analyzed with Rietveld method so as to refine the unit cell dimensions. The volumetric thermal expansion coefficient are observed to be 2.98*10-5K-1 for orthorhombic Pbnm phase, 3.24*10-5K-1 for orthorhombic Cmcm phase, 3.75*10-5K-1 for tetragonal I4/mcm phase of SrZrO3 perovskite, and 2.06*10-5K-1 for cubic Pm3m phase of BaZrO3 perovskite, respectively. The linear thermal expansion coefficients of SrZrO3 perovskite show considerable anisotropy of α a >α c >α b for orthorhombic Pbnm phase, which reflect the decrease of distortion of the perovskite. It is demonstrated that thermal expansion of the centrosymmetrically distorted ABX3 perovskite can be empirically expressed as a combination of the changes of [B-X] bond length and tilting angle of BX6 octahedral framework. The octahedral tilting is considered to be the primary order parameter for the ferroelastic type of structural phase transitions in perovskite. Thermodynamically, the tilting induced volume change denotes the “excess volume” and the corresponding thermal expansion represents the “excess thermal expansion” for the lower symmetry phase with respect to its prototype of the cubic perovskite.
Effects of CaZrO3 on X8R Nonreducible BaTiO3-based dielectric ceramics

Guofeng Yao,Xiaohui Wang,Tieyu Sun,Longtu Li

DOI: https://doi.org/10.1111/j.1551-2916.2011.04563.x

IF: 4.186

2011-01-01

Journal of the American Ceramic Society

Abstract:Effects of CaZrO3 on BaTiO3-MgO-MnO2-Y2O3 nonreducible ceramics were investigated. The specimens modified by CaZrO3 in the range from 0 to2 mol% were prepared via conventional mixing method. Transmission electron microscopic analysis revealed that doping elements were enriched at grain boundaries and "core-shell" structures were formed. The addition of CaZrO3 could lower the sintering temperature. The Curie temperature was shifted to a higher point with increasing CaZrO3, attributed to the existence of an internal stress produced by lattice mismatch between grain cores and shells. Temperature dependence of dielectric constant and capacitance change were also dependent on CaZrO3 content. With the increasing of CaZrO3 content, the insulation resistivity was improved whereas the degradation under direct current electrical field was significant. Therefore, a proper CaZrO3 content is crucial to obtain high performance X8R nonreducible BaTiO3-based dielectrics.
Effect of B-site complex substitutions on orthorhombic distortion and microwave dielectric properties of Ca(Zr 0.95 Ti 0.05 )O 3 perovskites

Xin Wang,Tao Zhou,Wei Wang,Zhaochen Xi,Diming Xu,Chao Du,Xiao-Gang Yao,Hui-Xing Lin,Huiqi Xia,Biaobing Jin,Yongqiang Pang,Haijie Zhang,Chao Liang,Di Zhou

DOI: https://doi.org/10.1039/d4tc00062e

IF: 6.4

2024-01-01

Journal of Materials Chemistry C

Abstract:The effects of complex-ion (Zn 1/3 Nb 2/3 ) 4+ substitutions on the crystal structure, microstructure and microwave dielectric properties of Ca(Zr 0.95 Ti 0.05 )O 3 were shown.

materials science, multidisciplinary,physics, applied
High temperature mechanical and thermal properties of CaxBa1-xZrO3 solid solutions

Wei Zhang,Juanli Zhao,Peiying Wang,Yuchen Liu,Peng Song,Danyu Jiang,Wenxian Li,Yanchun Zhou,Lan Yang,Hongqiang Nian,Bin Liu

DOI: https://doi.org/10.1016/j.ceramint.2020.04.032

IF: 5.532

2020-08-01

Ceramics International

Abstract:The excellent high temperature phase stability enables the perovskite BaZrO3 to be a promising candidate for thermal barrier coatings (TBCs). Further improvement of its thermo-physical properties is necessary to fulfill the increasing requirements for TBCs. In this work, CaxBa1-xZrO3 (x = 0.05, 0.10, 0.15, 0.20, 0.25) solid solutions are fabricated and the influence of the Ca2+ content on their mechanical/thermal properties is studied. They have moderate mechanical properties and their residual Young's moduli at 1473 K are around 80% of the values at room temperature. Compared with BaZrO3, CaxBa1-xZrO3 solid solutions have decreased thermal conductivities which are comparable to those of YSZ and other potential TBCs materials. Among these solid solutions, Ca0.25Ba0.75ZrO3 exhibits the lowest thermal conductivity that is in the range from 2.06 W ⋅ m - 1 ⋅ K - 1 to 2.52 W ⋅ m - 1 ⋅ K - 1 . Meanwhile, CaxBa1-xZrO3 solid solutions have higher thermal expansion coefficients than that of BaZrO3. These good high temperature mechanical and thermal properties reveal their promising applications as high temperature structural ceramics including TBCs.

materials science, ceramics
EFFECT OF DOPING CaO ON DIELECTRIC PROPERTIES OF BaZr0.05Ti0.95O3 CERAMICS

W. Kang,Z. Zheng,Y. Li,R. Zhao,W. Dun,Y. Wang

2018-01-01

Digest Journal of Nanomaterials and Biostructures

Abstract:CaO-doped BaZr0.05Ti0.95O3 (BZT) ceramics were prepared by the conventional solid state reaction rout, and the effects of CaO on phase composition, microstructure development and temperature-dependent dielectric properties were investigated. The phase composition was analyzed by XRD pattern, and the microstructures of the samples were observed by scanning electron microscopy (SEM), and their dielectric properties were measured at 1 kHz. The variation of dielectric properties at different sintering temperature was also discussed. The results of XRD test show that the main crystal phase of BZT based ceramics does not change obviously, and the perovskite structure is still present. However, with the increase of the amount of doping, some impurity phase will be produced. Microstructure analysis shows that the doping of calcium oxide to BZT can make the grain more compact and homogeneous. When BZT ceramics doped with CaO as 5 mol% and the sintering temperature is 1330 degrees C, the grain size is more uniform and the growth is better. With the increase of CaO contents the dielectric constant increased and reached a maximum value at 5mol%. The dielectric loss decrease with increasing CaO concentration, and the value of Tm is regularly shifted to lower temperature and broaden. Dielectric properties of doped samples were significantly modified.
Structural and Dielectric Properties in the (ba1−ca )(ti0.95zr0.05)o3 Ceramics

Guozhong Zang

DOI: https://doi.org/10.1016/j.cap.2011.10.013

IF: 2.856

2011-01-01

Current Applied Physics

Abstract:Lead-free (Ba1-xCax)(Ti0.95Zr0.05)O-3 (x = 0.05-0.40) (BCZT) ceramics were prepared by solid-state reaction technique. XRD results show that the samples in the composition range of 0.05 <= x <= 0.25 exhibit pure perovskite structures and undergo a polymorphic phase transitions from orthorhombic to tetragonal phase around room temperature. The biphasic structures are detected at x >= 0.30 and the dielectric peaks become broad and dielectric constants decrease with increasing Ca content. Ca replacement at Ba site leads to diffuseness, whereas Ca occupancy at Ti site leads to decrease of the T-c. (C) 2011 Elsevier B. V. All rights reserved.
Effect of B-site Complex Substitutions on Orthorhombic Distortion and Microwave Dielectric Properties of Ca(Zr0.95Ti0.05)O3 Perovskites

Xin Wang,Tao Zhou,Wei Wang,Zhaochen Xi,Diming Xu,Chao Du,Xiao-Gang Yao,Hui-Xing Lin,Huiqi Xia,Biaobing Jin,Yongqiang Pang,Haijie Zhang,Chao Liang,Di Zhou

DOI: https://doi.org/10.1039/d4tc00062e

IF: 6.4

2024-01-01

Journal of Materials Chemistry C

Abstract:The effects of complex-ion (Zn1/3Nb2/3)4+ substitutions on the crystal structure, microstructure and microwave dielectric properties of Ca(Zr0.95Ti0.05)O3 were shown.
Effect of CaO doping on densification and micr‐ostructure control of highly transparent La0.4Gd1.6Zr2O7 ceramics

Shiwei Deng,Lexing Liang,Zhe Tang,Haifeng Yuan,Cong Zhang,Zijie Li,Junjing Duan,Jianqi Qi,Tiecheng Lu

DOI: https://doi.org/10.1111/jace.18940

IF: 4.186

2022-12-13

Journal of the American Ceramic Society

Abstract:Calcium oxide (CaO) as sintering additive was firstly used to fabricate La0.4Gd1.6Zr2O7 transparent ceramics by a simple solid‐state reaction and one‐step vacuum sintering method. The effects of CaO dopant amount on the densification, as well as sintering behaviors and microstructure evolution of the as‐fabricated La0.4Gd1.6Zr2O7 ceramics were systematically investigated. Under the different sintering temperature, the relationship during the sintering process between grain growth and pore elimination were analyzed as well. It was found that 0.1 wt% CaO doping can effectively control the rate of grain growth and promote densification dominated by surface diffusion. Furthermore, Ca2+ entered the lattice of La0.4Gd1.6Zr2O7 ceramics to accelerate ion diffusion and suppress grain boundary migration. With the introduction of 0.1 wt% CaO doping, the highly transparent La0.4Gd1.6Zr2O7 ceramics (T = 80.4% at 1100nm) were successfully fabricated at the traditional sintering temperature (1850C). This article is protected by copyright. All rights reserved

materials science, ceramics
The Study of Ca-doped BCTZ Ceramics Sintered in Reducing Atmosphere

Lei Chen,Longtu Li,Xiaohui Wang,Zhibin Tian,Zhilun Gui

DOI: https://doi.org/10.1007/s10832-007-9245-9

2007-01-01

Journal of Electroceramics

Abstract:Effects of Ca2+ doped into (Ba1 − xCax)(Ti1 − yZry)O3 (BCTZ) ceramics on microstructure and insulation resistance have been investigated. It is found that the shift of Ca2+ from A-sites to B-sites greatly influences the unit cell volume and the Curie temperature of BCTZ ceramics. During the firing process in reducing atmosphere, the large amounts of additive Ca2+ dispense among the grain boundaries and lead to the restrain of the grain growth. Within the same volume, the specimen with smaller grain size provides more grain boundaries, which helps in providing an efficient diffusion pathway for oxygen during annealing step and results in the improvement of the insulation resistance of the samples.
Effect of Zr4+ content on crystal structure, micromorphology, ferroelectric and dielectric properties of Ba(ZrxTi1−x)O3 ceramics

Lei Xu,Yuan Xu

DOI: https://doi.org/10.1007/s10854-020-03114-2

2020-02-24

Abstract:Ba(ZrxTi1−x)O3 ceramics (x = 0.15, 0.2, 0.25, 0.3) were prepared with solid-state reaction method. The ratio of Zr/Ti influences the crystal structure, micromorphology, ferroelectric and dielectric properties of BZT ceramics, which were characterized, respectively, by X-ray diffraction, scanning electron microscope, ferroelectric test system and dielectric test system. The X-ray diffraction patterns show that the zirconium titanate ceramic samples adopt cubic phase structure and no secondary phase. As the Zr4+ content increases, the lattice constant increases and the grain size decreases. BZT ceramic sample with 15% zirconium content has the highest dielectric constant. As the Zr4+ content increases, the dielectric constant is gradually decreased, and Curie temperature dropped from 334 to 226 K. The sample has the largest remanent polarization, when the zirconium ion content is 15%. Subsequently, the remanent polarization is reduced as the zirconium ion content increases.

engineering, electrical & electronic,materials science, multidisciplinary,physics, condensed matter, applied
Crystal structure solution and high-temperature thermal expansion in NaZr2(PO4)3-type materials

Benjamin S. Hulbert,Julia E. Brodecki,Waltraud M. Kriven

DOI: https://doi.org/10.1107/s2052520624001598

2024-03-22

Acta Crystallographica Section B Structural Science Crystal Engineering and Materials

Abstract:The NaZr2P3O12 family of materials have shown low and tailorable thermal expansion properties. In this study, SrZr4P6O24 (SrO·4ZrO2·3P2O5), CaZr4P6O24 (CaO·4ZrO2·3P2O5), MgZr4P6O24 (MgO·4ZrO2·3P2O5), NaTi2P3O12 [1⁄2(Na2O·4TiO2·3P2O5)], NaZr2P3O12 [1⁄2(Na2O·4ZrO2·3P2O5)], and related solid solutions were synthesized using the organic–inorganic steric entrapment method. The samples were characterized by in-situ high-temperature X-ray diffraction from 25 to 1500°C at the Advanced Photon Source and National Synchrotron Light Source II. The average linear thermal expansion of SrZr4P6O24 and CaZr4P6O24 was between −1 × 10−6 per °C and 6 × 10−6 per °C from 25 to 1500°C. The crystal structures of the high-temperature polymorphs of CaZr4P6O24 and SrZr4P6O24 with R3c symmetry were solved by Fourier difference mapping and Rietveld refinement. This polymorph is present above ∼1250°C. This work measured thermal expansion coefficients to 1500°C for all samples and investigated the differences in thermal expansion mechanisms between polymorphs and between compositions.

chemistry, multidisciplinary,crystallography
Thermal Expansion Coefficients of Sm2Zr2O7 Doped with MgO

Zhi Xue Qu,Wei Pan,Chun Lei Wan,Ye Xia Qin

DOI: https://doi.org/10.4028/www.scientific.net/KEM.336-338.2331

2007-01-01

Key Engineering Materials

Abstract:Thermal expansion coefficient (TEC) is one of the most concerned properties for thermal barrier coating (TBC) materials. To enhance thermal expansion coefficient, a series of rare-earth zirconates Sm2Zr2O7 with various contents of MgO were investigated. The samples were synthesized by solid state reaction at 1600 degrees C for 10h. And the thermal expansion coefficients of the samples were measured. The results showed that all the doping samples had higher expansion coefficients than pure Sm2Zr2O7. Moreover, compared with the data reported of 8YSZ, similar to 15% enhancement had been achieved above 300 degrees C.
Effect of CaO on structure and properties of AZ61 magnesium alloy

Umer Masood Chaudry,Yeonju Noh,Gukin Han,Russlan Jaafreh,Tea-Sung Jun,Kotiba Hamad

DOI: https://doi.org/10.1016/j.msea.2022.143189

2022-06-01

Abstract:In this study, the effects of CaO additions on microstructure, texture, and mechanical properties of AZ61 magnesium (Mg) alloy were investigated. For this target, AZ61 Mg alloy samples containing 0.5 and 1 wt.% CaO were investigated. The results showed that the addition of CaO leads to formation Ca-rich intermetallic compounds, which in turn, influenced the structure evolution of the alloy. In addition, it was observed the formation of twined structures in the alloys containing CaO, where the fraction of tension twins increased by increasing the amount of CaO. This was conjugated with the evolution of non-basal texture components, as found by the orientation distribution functions recorded for the investigated samples. Mechanical properties showed that the ductility of the AZ61 Mg alloy reduced by the CaO addition, whereas the yield strength was enhanced in the AZ61-1CaO sample.

materials science, multidisciplinary,nanoscience & nanotechnology,metallurgy & metallurgical engineering
Sintering, thermal expansion and mechanical properties of K0.6Sr0.7Zr4P6O24 ceramics

郭兴忠,杨辉,胡晓珍,葛曼珍

DOI: https://doi.org/10.3785/j.issn.1008-973X.2004.07.028

2004-01-01

Abstract:K0.6Sr0.7Zr4P6 O24 (KSZP) ceramics were prepared with KSZP nanometer powder as the raw material synthesized by phosphate direct co-precipitation. The sintering, thermal expansion and mechanical properties of the KSZP ceramics were studied, and the effects of sintering conditions on these properties were analyzed. The obtained suitable sintering conditions for KSZP ceramics are as follows: Nb2O5 additive is 2%, sintering temperature is 1380°C and sintering time is 2 h. The relative density of KSZP ceramics sintered under above conditions is about 94.61% , the bending strength is 91.83 MPa, and the average value of thermal expansion coefficient at 0-600°C is about 1.4×10-6/°C, which is under very low level. The sintering rate is supposed to be rapid, and the crystalline grain does not grow rapidly in the final stage.

Effect of CaO on the thermal expansion of Ca0.5Zr2 (PO4)3

Anisotropic Chemical Expansion Of La1-Xsrxcoo3-Delta

Effect of CaO Content on Properities of 3-1 Type Porous Lead Zirconate Titanate Ceramics

The effect of BaO addition on the sintering properties and grain growth behavior of CaZrO3 ceramics

Effects Of Catio(3)On Microstructures And Properties Of (1-X) Znal2o4-Xmg(2) Tio4 (X=0.1) Microwave Dielectric Ceramics

Effect of Vacancy on Thermal Expansion Coefficient of Sm2Zr2O7 Ceramic

Effect of Mass Fraction of CeO2 on Structure of Zirconolite-based Glass-ceramics

Thermal Expansion of SrZrO3 and BaZrO3 Perovskites

Effects of CaZrO3 on X8R Nonreducible BaTiO3-based dielectric ceramics

Effect of B-site complex substitutions on orthorhombic distortion and microwave dielectric properties of Ca(Zr 0.95 Ti 0.05 )O 3 perovskites

High temperature mechanical and thermal properties of CaxBa1-xZrO3 solid solutions

EFFECT OF DOPING CaO ON DIELECTRIC PROPERTIES OF BaZr0.05Ti0.95O3 CERAMICS

Structural and Dielectric Properties in the (ba1−ca )(ti0.95zr0.05)o3 Ceramics

Effect of B-site Complex Substitutions on Orthorhombic Distortion and Microwave Dielectric Properties of Ca(Zr0.95Ti0.05)O3 Perovskites

Effect of CaO doping on densification and micr‐ostructure control of highly transparent La0.4Gd1.6Zr2O7 ceramics

The Study of Ca-doped BCTZ Ceramics Sintered in Reducing Atmosphere

Effect of Zr4+ content on crystal structure, micromorphology, ferroelectric and dielectric properties of Ba(ZrxTi1−x)O3 ceramics

Crystal structure solution and high-temperature thermal expansion in NaZr2(PO4)3-type materials

Thermal Expansion Coefficients of Sm<sub>2</sub>Zr<sub>2</sub>O<sub>7</sub> Doped with MgO

Effect of CaO on structure and properties of AZ61 magnesium alloy

Sintering, thermal expansion and mechanical properties of K0.6Sr0.7Zr4P6O24 ceramics