Generation of the 1.871 μm laser oscillation from a monomode Tm3+-doped silicate fiber

Dongfeng Liu,Geguo Du,Xianhua Wang,Guofu Chen,Ling Ruan

1998-01-01

Abstract:The preliminary experimental results of the generation of the 1.871 μm laser oscillation from a monomode Tm3+-doped silicate fiber pumped by a 1.053 μm laser is reported. The maximum output power is 153 μW, and the slope efficiency is 0.32%.

What problem does this paper attempt to address?

14.7Mj Total Output from a Gain-Switched Tm3+-doped Double-Clad Silica Fiber Laser

YJ Zhang,YZ Wang

DOI: https://doi.org/10.1117/12.667141

2006-01-01

Abstract:A gain-switched Tm-doped double-clad silica fiber laser operating at a wavelength of approximately 2 mu m with moderate output energy is realized. A gain-switched Nd:YAG laser is used to pump the H-3(5) energy level of the doped Tm3+ ions at 1.064 mu m, and a maximum total output energy of 14.7mJ per pulse is produced at a slope efficiency of 39.5% (with respect to launched pump energy). As we know, this is the first time to realize the gain-switched Tm3+-doped double-clad silica fiber laser pumped at 1.064 mu m, and both the single pulse energy and the slope efficiency exceed the reported results that produced from single-clad Tm3+-doped silica fiber laser in the past. The results of three different length fibers in experiments are present and contrasted. Because the absorption section at 1.064 mu m is only 2.5% at 0.79 mu m in TM3+-doped silica fiber, we use three relative long fibers (the fiber. 1 length 35 m, fiber.2 length 8m, the fiber.3 length 1m.) to increase the absorption ratios. The laser threshold in fiber. 1, fiber.2 and fiber.3 is 37.5mJ, 39.4mJ and 48 mJ, and the slope efficiency is 39.5%, 11.6% and 1% respectively. The output peak wavelength from fiber. I fiber.2 and fiber.3 is 2.04 mu m, 2.01 mu m and 1.92 mu m measured by a monochromator respectively.
Experimental Investigation of Tm3+-Doped Silica Double-Cladding Fibre Laser

Zhang Yun-Jun,Wang Yue-Zhu,Ju You-Lun,Yao Bao-Quan

DOI: https://doi.org/10.1088/0256-307x/23/9/028

2006-01-01

Chinese Physics Letters

Abstract:Using a Tm3+-doped double-cladding silica fibre, we produce a maximum cw 2.2 W output at approximately 2 μm. The highest achieved slope efficiency is 29.3% respect to the launched pump power. The lowest threshold is 1.85 W using the double pass pump method with the fibre length 2.7 m, which is the lowest reported threshold of cladding pump of the 3H4 level. The fibre laser output peak wavelength ranges from 1.967 μm to 2.018 μm with cavity 1 (R1 = 1 and R2 = 0.04) and from 1.95 μm to 1.99 μm with cavity 2 (R1 = 0.04 and R2 = 0.04), as the fibre length varies.
4.3 GHz fundamental repetition rate passively mode-locked fiber laser using a silicate-clad heavily Tm<sup>3+</sup>-doped germanate core multimaterial fiber

Guowu Tang,Zhaoheng Liang,Wenhua Huang,Dongliang Yang,Wei Lin,Le Tu,Dongdan Chen,Qi Qian,Xiaoming Wei,Zhongmin Yang

DOI: https://doi.org/10.1364/ol.447251

IF: 3.6

2022-01-01

Optics Letters

Abstract:We report a silicate-clad heavily Tm3+-doped germanate core multimaterial fiber that is successfully drawn by using a rod-in-tube method. This new fiber has a high gain per unit length of 6.11 dB/cm at 1.95 µm, which is, to the best of the authors’ knowledge, the highest gain per unit length reported so far for Tm3+-doped glass fibers. By virtue of this high-gain glass fiber, an all-fiber-integrated passively mode-locked fiber laser with a fundamental repetition rate up to 4.3 GHz is demonstrated. Remarkably, the generated pulse operating at 1968 nm exhibits a signal-to-noise ratio of >76 dB in the radio-frequency domain. These results suggest that the silicate-clad heavily Tm3+-doped germanate core multimaterial fiber can act as a key building block for high repetition rate mode-locked fiber lasers at 2 µm.
4.3 GHz fundamental repetition rate passively mode-locked fiber laser using a silicate-clad heavily Tm3+-doped germanate core multimaterial fiber

Guowu Tang,Zhaoheng Liang,Wenhua Huang,Dongliang Yang,Wei Lin,Le Tu,Dongdan Chen,Qi Qian,Xiaoming Wei,Zhongmin Yang

DOI: https://doi.org/10.1364/OL.447251

IF: 3.6

2022-01-01

Optics Letters

Abstract:We report a silicate-clad heavily Tm3+-doped germanate core multimaterial fiber that is successfully drawn by using a rod-in-tube method. This new fiber has a high gain per unit length of 6.11 dB/cm at 1.95 mu m, which is, to the best of the authors' knowledge, the highest gain per unit length reported so far for Tm3+-doped glass fibers. By virtue of this high-gain glass fiber, an all-fiber-integrated passively mode-locked fiber laser with a fundamental repetition rate up to 4.3 GHz is demonstrated. Remarkably, the generated pulse operating at 1968 nm exhibits a signal-to-noise ratio of >76 dB in the radio-frequency domain. These results suggest that the silicate-clad heavily Tm3+-doped germanate core multimaterial fiber can act as a key building block for high repetition rate mode-locked fiber lasers at 2 mu m. (C) 2022 Optica Publishing Group
Tm^3+ Doped Lead Silicate Glass Single Mode Fibers for 20 Μm Laser Applications

Guowu Tang,Tingting Zhu,Wangwang Liu,Wei Lin,Tian Qiao,Min Sun,Dongdan Chen,Qi Qian,Zhongmin Yang

DOI: https://doi.org/10.1364/ome.6.002147

2016-01-01

Optical Materials Express

Abstract:Tm3+ doped lead silicate glasses with good thermal stability were prepared by the melt-quenching method. Based on the absorption and emission spectra, Judd-Ofelt intensity parameters, absorption and emission cross sections, gain spectra, and σe × FWHM were calculated and analyzed. These results suggest that Tm3+ doped lead silicate glasses are promising as mid-infrared laser materials. Tm3+ doped lead silicate glass single mode (SM) fibers with cladding diameter of 125 μm and core diameter of 8.5 μm were then fabricated by the rod-in-tube technique. The Tm3+ doping concentration reached as high as 4.545 × 1020 ions/cm3. ~2.0 μm amplified spontaneous emission (ASE) was realized in a 3.5-cm-long as-drawn SM fiber when pumped by a homemade single mode 1560 nm fiber laser. The results indicate that these Tm3+ doped lead silicate glass single mode fibers are promising fiber material for 2.0 μm fiber laser applications.
3 W Narrow-Linewidth Ultra-Short Wavelength Operation Near 1707 Nm in Thulium-Doped Silica Fiber Laser with Bidirectional Pumping

Xusheng Xiao,Haitao Guo,Zhijun Yan,Hushan Wang,Yantao Xu,Min Lu,Yishan Wang,Bo Peng

DOI: https://doi.org/10.1007/s00340-017-6713-z

2017-01-01

Applied Physics B

Abstract:We have developed an ultra-short wavelength operation of all-fiber Tm-doped laser system, in which the laser system was structured in a FBGs based linear cavity with FBG associated bidirectional pump mechanism at 1550 nm. The laser yielded 3.15 W of continuous-wave output at 1706.75 nm with a narrow-linewidth of ~50 pm. A high reflectivity FBG (HR-FBG) at 1550 nm was used to reflect the residual pump light and achieve the bidirectional pump mechanism. The maximum slope efficiency was improved from 23.2% without HR-FBG to 42.1% with HR-FBG at 1550 nm and the lowest pump threshold was reduced from 1.6 to 0.8 W accordingly. In the experiment, we have also investigated the dependencies of the slope efficiencies and pump threshold of the laser versus the length of active fiber and reflectivity of the output mirror (FBG) in detail. It is indisputable that the development of 1.7 μm silicate fiber lasers with Watt-level output power will open up a number of promising application windows.
An All Fiber 1.94 Μm Nanosecond Pulse Laser Amplified by Highly Tm 3+ -Doped Silicon Fibers

Zhou Ren-Lai,Ren Jian-Cun,Yang Chao,Ju You-Lun,Wang Yue-Zhu

DOI: https://doi.org/10.1088/0256-307x/30/5/054208

2013-01-01

Abstract:We present an all-fiber 1.94 μm nanosecond pulse laser in master oscillation-power amplifier configuration. A dual-FBGs gain-switched Tm3+-doped fiber laser is built and is used as the seed laser. The output characteristics of the amplifier are studied at different pulse repetition rates, and the maximum output energy of 500 μJ is achieved under incident pump power of 39 W. The emitting spectra are checked at 5 and 10 kHz, and no obvious nonlinear effects are observed in the spectrum of the amplified laser. The beam quality factor is M2 = 2.1 ± 0.03 measured by the traveling knife-edge method, and the laser beam spot is also monitored by an infrared vidicon camera.
Short Tm3+-doped Fiber Lasers with Watt-Level Output Near 2 Μm

Yulong Tang,Yong Yang,Xiaojin Cheng,Jianqiu Xu

DOI: https://doi.org/10.3788/col20080601.0044

2008-01-01

Abstract:High-power operation of diode-pumped fiber lasers at wavelength near 2 microns are demonstrated with short length of heavily Tm3+-doped silica glass fibers. With 7-cm long fiber, a laser at near 2 microns is obtained with the threshold of 135 mW, maximum output power of 1.09 W, and slope efficiency of 9.6% with respect to the launched power from a laser diode at 790 nm. The output stability of this fiber laser is within 5%. The dependence of the performance of fiber lasers on the operation temperature and cavity configuration parameters is also investigated.
400 mW narrow-linewidth Tm-doped silica fiber laser output near 1750nm with volume Bragg grating

Zhao Quan,Cunxiao Gao,Haitao Guo,Ning Wang,Xiaoxia Cui,Yantao Xu,Bo Peng,Wei Wei

DOI: https://doi.org/10.1038/srep12034

IF: 4.6

2015-01-01

Scientific Reports

Abstract:A type of Tm-doped silica fiber laser with narrow-linewidth and output wavelength near 1750 nm was firstly presented, by using a 1550 nm Er-doped fiber laser pump source and a volume Bragg grating (VBG). By means of a 15 cm Tm-doped fiber, a 400 mW continuous wave (cw) at ~1750 nm with FWHW of ~54 pm was generated, corresponding to an average slope efficiency up to 23.5% with respect to absorbed pump power. The influence of gain fiber length on the spectrum wavelength has been investigated in detail. All experimental results demonstrate that this fiber laser will be an effective and promising pump source for mid-IR laser output.
Tm 3+ doped lead silicate glass single mode fibers for 2.0 μm laser applications

Guowu Tang,Tingting Zhu,Wangwang Liu,Wei Lin,Tian Qiao,Min Sun,Dongdan Chen,Qi Qian,Zhongmin Yang

DOI: https://doi.org/10.1364/OME.6.002147

2016-01-01

Optical Materials Express

Abstract:Tm3+ doped lead silicate glasses with good thermal stability were prepared by the melt-quenching method. Based on the absorption and emission spectra, Judd-Ofelt intensity parameters, absorption and emission cross sections, gain spectra, and sigma(e) x FWHM were calculated and analyzed. These results suggest that Tm3+ doped lead silicate glasses are promising as mid-infrared laser materials. Tm3+ doped lead silicate glass single mode (SM) fibers with cladding diameter of 125 mu m and core diameter of 8.5 mu m were then fabricated by the rod-in-tube technique. The Tm3+ doping concentration reached as high as 4.545 x 10(20) ions/cm(3). similar to 2.0 mu m amplified spontaneous emission (ASE) was realized in a 3.5-cm-long as-drawn SM fiber when pumped by a homemade single mode 1560 nm fiber laser. The results indicate that these Tm3+ doped lead silicate glass single mode fibers are promising fiber material for 2.0 mu m fiber laser applications. (C) 2016 Optical Society of America
Ultra-short Wavelength Operation in Thulium-doped Silica Fiber Laser with Bidirectional Pumping

Xusheng Xiao,Haitao Guo,Zhijun Yan,Hushan Wang,Yantao Xu,Min Lu,Yishan Wang,Bo Peng

DOI: https://doi.org/10.1117/12.2256818

2017-01-01

Abstract:An ultra-short wavelength operation of Tm-doped all fiber laser based on fiber Bragg gratings (FBGs) was developed. A bi-directional pump configuration for the ultra-short wavelength operation was designed and investigated for the first time. the laser yielded 3.15W of continuous-wave output at 1706.75nm with a narrow-linewidth of ~50pm and a maximum slope efficiency of 42.1%. The dependencies of the slope efficiencies and pump threshold of the laser versus the length of active fiber and reflectivity of the output mirror (FBG) were investigated in detail. An experimental comparative study between two Thulium-doped fiber lasers (TDFLs) with two different pumping configuration(forward unidirectional pumping and bidirectional pumping) was presented. It is indisputable that the development of 1.7μm silicate fiber lasers with Watt-level output power open up a number of heart-stirring and tempting application windows.
Short Tm3+-Doped Fiber Lasers With Watt-Level Output Near 2 Mu M

yulong tang,yong yang,xiaojin cheng,jianqiu xu

IF: 2.56

2008-01-01

Chinese Optics Letters

Abstract:High-power operation of diode-pumped fiber lasers at wavelength near 2 pm are demonstrated with short length of heavily Tm3+-doped silica glass fibers. With 7-cm long fiber, a laser at near 2 mu m is obtained with the threshold of 135 mW, maximum output power of 1.09 W, and slope efficiency of 9.6% with respect to the launched power from a laser diode at 790 nm. The output stability of this fiber laser is within 5%. The dependence of the performance of fiber lasers on the operation temperature and cavity configuration parameters is also investigated.
High-power Gain-Switched Tm^3+-doped Fiber Laser

Yulong Tang,Lin Xu,Yi Yang,Jianqiu Xu

DOI: https://doi.org/10.1364/oe.18.022964

IF: 3.8

2010-01-01

Optics Express

Abstract:Gain-switched by a 1.914-µm Tm:YLF crystal laser, a two-stage Tm(3+) fiber laser has been achieved 100-W level ~2-µm pulsed laser output with a slope efficiency of ~52%. With the 6-m length of Tm fiber, the laser wavelength was centered at 2020 nm with a bandwidth of ~25 nm. Based on an acousto-optic switch, the pulse repetition rate can be modulated from 500 Hz to 50 kHz, and the laser pulse width can be tuned between 75 ns and ~1 µs. The maximum pulse energy was over 10 mJ, and the maximum pulse peak power was 138 kW. By using the fiber-coiling-induced mode-filtering effect, laser beam quality of M2 = 1.01 was obtained. Further scaling the pulse energy and average power from such kind of gain-switched fiber lasers was also discussed.
1.95 μm kHz-linewidth single-frequency fiber laser using self-developed heavily Tm 3+ -doped germanate glass fiber

xin he,shanhui xu,can li,changsheng yang,qi yang,shupei mo,dongdan chen,zhongmin yang

DOI: https://doi.org/10.1364/OE.21.020800

IF: 3.8

2013-01-01

Optics Express

Abstract:We demonstrated a kHz-linewidth single-frequency laser at 1.95 mu m using the self-developed heavily Tm3+ -doped single-mode germanate glass fiber with the net gain coefficient of 2.3 dB per centimeter. The maximum output power of the stable single longitudinal mode continuous wave laser is over 200 mW. The slope efficiency measured versus the absorbed pump power is 34.8%, the signal-to-noise ratio is higher than 68 dB and laser linewidth is less than 7 kHz. A wavelength-tuning from 1949.55 to 1951.23 nm was also demonstrated based on changing the tension on the fiber Bragg grating outside the cavity. (C) 2013 Optical Society of America
The Steady-state Behavior of 1565nm Laser Pumped Tm~(3+)∶Ho(3+) Co-doped Silica Fiber Laser

ZHOU Jun,DONG Shu-fu,ZHOU Yi-jian,LI Wei-min,CHEN Guo-fu

DOI: https://doi.org/10.3969/j.issn.1001-5078.2007.12.009

2007-01-01

Abstract:As a pump source,1565nm pumping band can efficiently diminish the loss of manifold fast non-radiative decay and upconversion losses compared to 800nm and 1180nm bands.Theoretical model of Tm3+∶Ho3+ co-doped silica fiber for 2μm laser pumped at 1565nm laser is established.After the comprehensive rate equations and propagation equations are given,characteristics of the system in steady state at hypothesis situation are analyzed by using numerical simulation way.As high as 1.7W laser output power was achieved with a slope efficiency of 67% and quantum efficiency of 57% when the pump power is 3W and fiber length is 2.2m.Numerical simulation results indicate better capability of the fiber and higher conversion efficiency as far as we know.
Frequency upconversion in homemade Tm3+-doped silica fibers pumped by 1053 nm

Gegou Du,Dongfeng Liu,Xianhua Wang,Guofu Chen,Lin Ruan

1999-01-01

Abstract:Frequency upconverted fluorescence from UV to infrared (387.4 nm, 477.4 nm, 651.4 nm, 802.9 nm) has observed and studied in homemade Tm3+-doped silica fibers pumped by CW Nd3 YLF laser at 1053 nm. The pump mechanism was given that red and blue light were produced through stepwise three-photo absorption and infrared light was done through stepwise two-photo absorption. The shoulder peak of blue and red light were also analyzed with all fluorescence spectra being measured.
227-W output all-fiberized Tm-doped fiber laser at 1908 nm

hu zhenyue,yan ping,xiao qirong,liu qiang,gong mali,胡震岳,闫平,肖起榕,柳强,巩马理

DOI: https://doi.org/10.1088/1674-1056/23/10/104206

2014-01-01

Chinese Physics B

Abstract:In this paper, we report that a diode-pumped thulium-doped double clad silica fiber laser can provide powers of up to 227 W at 1908 nm, corresponding to a slope efficiency of 54.3%, and an optical-to-optical efficiency of 51.2%. The output power, to the best of our knowledge, is the highest output at 1908 nm. The beam quality M-2 factor is about 1.56. Also discussed in this paper is the dependence of the laser performance on fiber length.
Narrow Linewidth Tm3+-Doped Large Core Fiber Laser Based on A Femtosecond Written Fiber Bragg Grating

Zhang Yun-Jun,Wang Wei,Zhou Ren-Lai,Song Shi-Fei,Tian Yi,Wang Yue-Zhu

DOI: https://doi.org/10.1088/0256-307x/27/7/074214

2010-01-01

Chinese Physics Letters

Abstract:A diode laser (LD) clad-pumped narrow linewidth all-fiber Tm3+-doped fiber laser is reported with a maximal output power of 27 W at 1.947μm. By successively splicing an LD pigtail fiber, a single-mode Tm3+-doped fiber, and a multi-mode Tm3+-doped fiber, the fiber laser has 70 pm narrow linewidth output, and a high slope efficiency of nearly 47.5% with respect to the launched pump power. The high reflectivity fiber Bragg gratings, which are directly written into the single-mode Tm3+-doped fiber core by the 800 nm femtosecond pulsed laser, act as the high reflectivity coupler. The output laser has diffraction-limited beam quality with a factor M2 of 1.29, when the output laser power is nearly 27 W.
High-efficiency sub-watt in-band-pumped single-frequency DBR Tm3+-doped germanate fiber laser at 1950 nm

Xianchao Guan,Changsheng Yang,Tian Qiao,Wei Lin,Qilai Zhao,Guowu Tang,Guoquan Qian,Qi Qian,Zhongmin Yang,Shanhui Xu

DOI: https://doi.org/10.1364/OE.26.006817

2018-03-19

Abstract:Based on a 1.8-cm-long heavily Tm3+-doped germanate fiber and being in-band-pumped by a 1610 nm single-mode laser, a high-efficiency and high-power single-frequency distribute Bragg reflector (DBR) fiber laser emitting at 1950 nm is demonstrated. The DBR fiber laser has a maximum output power of ~617 mW and a slope efficiency for the absorbed pump power reaches to more than 42.2%. A stable single-longitudinal-mode laser output with a signal-to-noise ratio of greater than 63 dB is realized. The measured relative intensity-noise of the fiber laser reaches to around -150 dB/Hz at frequencies of over 8.4 MHz. It is beneficial to exploit the sub-watt and high-efficiency single-frequency laser from fiber oscillators directly, especially in the application of multiple paths coherent beam combination and optical medical technology.
High Peak-Power Gain-Switched Tm$^{3+}$-Doped Fiber Laser

Yulong Tang,Feng Li,Jianqiu Xu

DOI: https://doi.org/10.1109/lpt.2011.2141983

IF: 2.6

2011-01-01

IEEE Photonics Technology Letters

Abstract:Resonantly pumped by a 1.914-mu m Q-switched Tm:YLF laser, high-peak-power stable laser pulse from gain-switched similar to 1.94-mu m Tm3+-doped silica fiber lasers are reported for the first time. The slope efficiency was over 80% with respect to absorbed pump power, and chaotic spiking was effectively eliminated by using fast gain switching. With a 4-m Tm3+ fiber, pulse energy of 1.3 mJ and pulsewidth of 61 ns were obtained, corresponding to peak power of 21.3 kW.

Generation of the 1.871 μm laser oscillation from a monomode Tm3+-doped silicate fiber

14.7Mj Total Output from a Gain-Switched Tm3+-doped Double-Clad Silica Fiber Laser

Experimental Investigation of Tm3+-Doped Silica Double-Cladding Fibre Laser

4.3 GHz fundamental repetition rate passively mode-locked fiber laser using a silicate-clad heavily Tm<sup>3+</sup>-doped germanate core multimaterial fiber

4.3 GHz fundamental repetition rate passively mode-locked fiber laser using a silicate-clad heavily Tm3+-doped germanate core multimaterial fiber

Tm^3+ Doped Lead Silicate Glass Single Mode Fibers for 20 Μm Laser Applications

3 W Narrow-Linewidth Ultra-Short Wavelength Operation Near 1707 Nm in Thulium-Doped Silica Fiber Laser with Bidirectional Pumping

An All Fiber 1.94 Μm Nanosecond Pulse Laser Amplified by Highly Tm 3+ -Doped Silicon Fibers

Short Tm3+-doped Fiber Lasers with Watt-Level Output Near 2 Μm

400 mW narrow-linewidth Tm-doped silica fiber laser output near 1750nm with volume Bragg grating

Tm 3+ doped lead silicate glass single mode fibers for 2.0 μm laser applications

Ultra-short Wavelength Operation in Thulium-doped Silica Fiber Laser with Bidirectional Pumping

Short Tm3+-Doped Fiber Lasers With Watt-Level Output Near 2 Mu M

High-power Gain-Switched Tm^3+-doped Fiber Laser

1.95 μm kHz-linewidth single-frequency fiber laser using self-developed heavily Tm 3+ -doped germanate glass fiber

The Steady-state Behavior of 1565nm Laser Pumped Tm~(3+)∶Ho(3+) Co-doped Silica Fiber Laser

Frequency upconversion in homemade Tm3+-doped silica fibers pumped by 1053 nm

227-W output all-fiberized Tm-doped fiber laser at 1908 nm

Narrow Linewidth Tm3+-Doped Large Core Fiber Laser Based on A Femtosecond Written Fiber Bragg Grating

High-efficiency sub-watt in-band-pumped single-frequency DBR Tm3+-doped germanate fiber laser at 1950 nm

High Peak-Power Gain-Switched Tm$^{3+}$-Doped Fiber Laser