Several optimization problems of chemical reactor

Jiamo Yang,Yuanxin Wu

1997-01-01

Abstract:The optimum reacting time of intermittent operating reactor and continuous operating reactor as well as the optimum feeding mode of continuous reactor were researched. It was also analyzed on the selection of type of continuous reactor, which makes a certain instructive sense to the actual production.

What problem does this paper attempt to address?

Production Optimization for Concentration and Volume-Limited Fed-Batch Reactors in Biochemical Processes

Ping Liu,Xinggao Liu,Zeyin Zhang,Yalin Wang,Chunhua Yang,Weihua Gui

DOI: https://doi.org/10.1007/s00449-017-1875-y

IF: 3.434

2018-01-01

Bioprocess and Biosystems Engineering

Abstract:Since a very slight violation of constraint could cause process safety and product quality problems in biochemical processes, an adaptive approach of fed-batch reactor production optimization that can strictly satisfy constraints over the entire operating time is presented. In this approach, an improved smooth function is proposed such that the inequality constraints can be transformed into smooth constraints. Based on this, only an auxiliary state is needed to monitor violations in the augmented performance index. Combined with control variable parameterization (CVP), the dynamic optimization is executed and constraint violations are examined by calculating the sensitivities of states to ensure that the inequality constraints are satisfied everywhere inside the time interval. Three biochemical production optimization problems, including the manufacturing of ethanol, penicillin and protein, are tested as illustrations. Meanwhile, comparisons with pure penalty CVP method, famous dynamic optimization toolbox DOTcvp and literature results are carried out. Research results show that the proposed method achieves better performances in terms of optimization accuracy and computation cost.
Comments on “optimal Use of Mixed Catalysts for Two Successive Chemical Reactions”

Guodong Li,Xinggao Liu

DOI: https://doi.org/10.1007/s10957-014-0641-4

2014-01-01

Journal of Optimization Theory and Applications

Abstract:The paper "Optimal use of mixed catalysts for two successive chemical reactions" by Jackson was first presenting an analytical solution for the plug flow reactor catalyst blend problem. However, the exact optimal value of the problem was not given, which has caused confusion and inaccuracies in the subsequent literatures. As a supplement and correction, this study gives the optimal solutions and optimal objective values analytically for the cases when the reactor length equals 1 and 12. These results are also verified numerically using the time-scaling method.
Dynamic optimization of operation of heat-integrated distillation column systems

Weirong Hong,Shuqing Wang,Pu Li,Wozny, G.

DOI: https://doi.org/10.1109/WCICA.2004.1343141

2004-01-01

Abstract:Because of their higher efficiency of energy utilization, heat-integrated distillation columns are widely used in the chemical industry. The strong coupling of columns due to the heat integration leads to difficulties for control and optimization. This work concerns the dynamic optimization of heat-integrated columns, because such processes are often disturbed by product and feed switchover. We propose to use an efficient sequential optimization approach to determine dynamic policies for minimizing operating costs of such processes. The numerical algorithm for sensitivity computation is improved and the computational expense is significantly reduced. The approach is successfully applied to a rigorous model of a pilot two-pressure distillation column system.
Modeling and Optimization of Ethane Steam Cracking Process in An Industrial Tubular Reactor with Improved Reaction Scheme

Mohsin Ali,Liao Zuwei,Yao Yang,Sun Jingyuan,Jiang Binbo,Wang Jingdai,Yang Yongrong

2020-01-01

Abstract:Ethane steam cracking process in an industrial reactor was investigated. An one-demsional (1D) steady-state model was developed firstly by using an improved molecular reaction scheme and was then simulated in Aspen Plus. A comparison of model results with industrial data and previously reported results showed that the model can predict the process kinetics more accurately. In addition, the validated model was used to study the effects of different process variables, including coil outlet temperature (COT), steam-to-ethane ratio and residence time on ethane conversion, ethylene selectivity, products yields, and coking rate. Finally, steady-state optimization was conducted to the operation of industrial reactor. The COT and steam-to-ethane ratio were taken as decision variables to maximize the annual operational profit.
Optimization of an industrial batch polycondensation reactor

Z. Weitao,W. Wuqian,Shao Zhijiang,Z. Yuyue,Qian Jixin

DOI: https://doi.org/10.1109/ACC.2001.945572

2001-01-01

Abstract:The operation of an industrial batch polycondensation reactor is optimized using sequential quadratic programming (SQP) method. Optimal reactor temperature trajectory is obtained to reduce the reaction time. Various product quality and safety related constraints are also considered. Optimization results show the proposed optimal temperature trajectory can reduce the reaction time significantly
Dynamic Optimization of Multivariable Endothermic Reaction in Cascade CSTR

Yang Chen,Zhijiang Shao,Jixin Qian,Kexin Wang,Zhiliang Zhan,Zuhua Xu

DOI: https://doi.org/10.1109/wcica.2010.5553780

2010-01-01

Abstract:The dynamic optimization problem of a multivariable endothermic reaction in cascade continuous stirred tank reactors is solved with simultaneous method in this paper. Radau collocation is applied in discretization because of its stiff decay and high precision. A two-layer optimization is presented to get a fast convergence rate when dealing with the nonlinear case. In the industry process, the load variation may be very large and may cause output variable's big overshoot. In order to reduce the overshoot, a segmentation load variation method is introduced. The good results of this nonlinear ordinary differential equations system show the validity of these methods.
Optimal Scheduling of the Multigrade Parallel Distillation Column System with a Continuous-Time Formulation

Fanglin Shao,Xiang Li,Lingyu Zhu,Han Gong,Xi Chen

DOI: https://doi.org/10.1021/acs.iecr.9b04258

2019-01-01

Industrial & Engineering Chemistry Research

Abstract:In the fine chemical industry, optimal scheduling of continuous processes involving multigrade and parallel units is an important problem. The existing scheduling formulations can be classified into continuous-time (CT) and discrete-time (DT) formulations. Most previous studies adopted DT approaches that are more convenient for establishing an optimization model. However, the DT formulation has two inherent shortcomings. One is that it often requires more integer variables than the CT formulation. The other is that the solution of a DT formulation is often only suboptimal, or even infeasible, for the original scheduling problem. This work proposes a CT formulation for optimal scheduling of multigrade parallel distillation processes. This formulation simultaneously addresses continuous demand satisfaction, sequence-dependent transitions, and run-length constraints. The performance of the proposed model is demonstrated through the solution of three different delivery scenarios and is shown to be better than that of a DT formulation in terms of both model scales and solution accuracy, from which one can infer the advantages of the CT formulation in dealing with time-related issues for process scheduling.
An Overview on Chemical Process Operation Optimization

Weimin Zhong,Rongbin Qi,Wenli Du,Feng Qian

2014-01-01

Abstract:This article first reviewed the history of process optimization. Process control, advanced control, and real-time optimization, together with scheduling and planning were then surveyed and the focuses were placed mainly on the research and application topics of real-time optimization. Multi-objective optimization, mixed integer linear programming and dynamic optimization problems were illustrated as typical examples of industrial operation optimization in real-time optimization, planning and scheduling layers. Finally, challenges in research and application of large-scale chemical process operation optimization, especially in process modeling and collaborative optimal control, were summarized.
Acrylonitrile Reactor On-Line Operation Optimization Software and Its Application

Mei-sheng XUE,Zhi-gang ZHANG,Gang WU,De-min SUN

DOI: https://doi.org/10.3321/j.issn:1000-8144.1999.05.012

1999-01-01

Abstract:After introducing the principles of on-line optimization based on multivariable step-wise regression and adaptive on-line steady state optimization, the paper describes the acrylonitrile reactor on-line operation optimization software ANOpt and its application. ANOpt is a functional, reliable and easily-operable software. When ANOpt is applied, the acrylonitrile production ratio can be increased notably, and great economic benefit can be obtained.
OPERATION OPTIMIZATION OF A PROPYLENE CHLOROHYDRIN REACTOR

Guo-bin WU,Xing-gui ZHOU,Wei-kang YUAN

DOI: https://doi.org/10.3969/j.issn.1001-7631.2000.04.007

2000-01-01

Abstract:A two-phase approach was used for the optimization of a propylene chlorohydrin reactor in a 10,000 t/year propylene oxide plant based on a simplified steady-state model. The chlorohydrin process was considered as two bubble reactors connected in series, the first one being the chlorine absorber and the second one the chlorohydrination reactor. The gas was assumed to be plug flow and the liquid complete mixing flow in both of the two reactors. The influence of the operating variables on the conversion and the yield was investigated by process simulation. It was demonstrated that there exists an optimal temperature at which the yield is maximized. It was indicated that low feed gas ratios, low propylene chlorohydrin concentrations and high recycle gas velocities are all favorable to improve the yield. The process profit was improved significantly after optimization. Approaches for further improvement of the operation were also suggested.
Advances in methods of reactor network synthesis and optimizat ion

陈启石,冯霄

DOI: https://doi.org/10.3321/j.issn:0253-4320.2002.05.004

2002-01-01

Abstract:Methods of reactor network synthesis and optimization show great advantages compared with traditional measures when they are used to select reactor types and reaction conditions. Fundamental principles and developments of various methods of reactor network synthesis and optimization are summarized. Merits and shortcomings of these methods are analyzed. Such methods include approaches based on process characteristics such as attainable region approach and derivative analytic ap-proach , approaches based on superstructure optimization and approaches based on targets such as targeting approach, constructive targeting approach and constructive MINLP approach. There are also empirical deduction methods and distributed parameter methods. Research trends in this field are also analyzed.
Optimization of Volatile Fatty Acid Production with Co-Substrate of Food Wastes and Dewatered Excess Sludge Using Response Surface Methodology

Chen Hong,Wu Haiyun

DOI: https://doi.org/10.1016/j.biortech.2010.02.013

IF: 11.4

2010-01-01

Bioresource Technology

Abstract:Central-composite design (CCD) and response surface methodology (RSM) were used to optimize the parameters of volatile fatty acid (VFA) production from food wastes and dewatered excess sludge in a semi-continuous process. The effects of four variables (food wastes composition in the co-substrate of food wastes and excess sludge, hydraulic retention time (HRT), organic loading rate (OLR), and pH) on acidogenesis were evaluated individually and interactively. The optimum condition derived via RSM was food wastes composition, 88.03%; HRT, 8.92days; OLR, 8.31gVSS/ld; and pH 6.99. The experimental VFA concentration was 29,099mg/l under this optimum condition, which was well in agreement with the predicted value of 28,000mg/l.
Graphical Optimization Method for Coupled Heat Exchanger Network and Reactor

Di Zhang,Guilian Liu,Yongfei Li

DOI: https://doi.org/10.1016/j.energy.2018.05.089

IF: 9

2018-01-01

Energy

Abstract:In chemical process industry, the reactor’s operating parameters (conversion and selectivity) affect their temperatures, as well as the integration of the Heat Exchanger Network (HEN). It is necessary to consider the integration of the HEN and the optimization of the reactor parameters simultaneously. A Pinch-based method is developed to integrate HEN and optimize the inlet and outlet temperature and energy consumption of reactors with multiple reactions. Based on the reaction kinetics, mass balance and energy balance, equations are deduced to show relations among temperatures, selectivity and conversion of reactor, energy consumption and the energy consumption of unit production. According to the Composite Curves, the effect of temperature variation on HEN is analyzed for exothermic and endothermic reactions, respectively, and relations among temperatures, selectivity, utilities, energy consumption of unit product and conversion are deduced and plotted in the same diagram. The optimal utilities, inlet/outlet temperature, selectivity and conversion of the reactor can be identified from this diagram. A benzene to cyclohexene process is studied to illustrate the application of the proposed method, and the result shows that the energy consumption of unit product can be reduced by 16.3% when the conversion of benzene is increased from 0.4 to 0.58.
Modelling and Operation Conditions Optimization of Ethylene Oxychlorination in Fluidized Bed Reactors

Chen Miao,Xu Zhimei,Sun Weizhen,Zhao Ling

2012-01-01

Abstract:According to industrial baffled fluidized bed reactor of ethylene oxychlorination,tanks-in-series reactor model on the basis of two-phase theory were developed.Plenty of industrial data was used for calculating the model parameters and testing the reactor model.The results show that the simulation value and industry value anastomose basically.On the base of the above,the optimal operating conditions of the reactor under various production loads can be obtained by optimizing the operating conditions of the reactor.
Optimization of chemical reactor feed by simulations based on a kinetic approach

Charles Guinand,Michal Dabros,Bertrand Roduit,Thierry Meyer,Francis Stoessel

DOI: https://doi.org/10.2533/chimia.2014.746

Abstract:Chemical incidents are typically caused by loss of control, resulting in runaway reactions or process deviations in different stages of the production. In the case of fed-batch reactors, the problem generally encountered is the accumulation of heat. This is directly related to the temperature of the process, the reaction kinetics and adiabatic temperature rise, which is the maximum temperature attainable in the event of cooling failure. The main possibility to control the heat accumulation is the use of a well-controlled adapted feed. The feed rate can be adjusted by using reaction and reactor dynamic models coupled to Model Predictive Control. Thereby, it is possible to predict the best feed profile respecting the safety constraints.
Novel Methodology for Targeting the Optimal Reactor and Operating Parameters Based on the Chemical System’s Overall Performance Within Catalyst Lifecycle

Liwen Zhao,Guilian Liu

DOI: https://doi.org/10.1016/j.ces.2024.120935

IF: 4.7

2024-01-01

Chemical Engineering Science

Abstract:Catalyst deactivation affects chemical system performance and reactor operation. A systematic method is proposed for targeting the optimal reactor, operating parameters, system performance, and catalyst service life, considering the catalyst deactivation. Relations between reactor performance, operating parameters, and running time are clarified based on the coupling analysis of the reactions, catalyst deactivation kinetics, and mass/energy balance. The influence of reactor fluctuation on energy cost and product output is explored by topological analysis, pinch analysis, and algebraic reasoning. A reactor-separator-heat exchanger network coupling frame is established to predict system performance and guide the reactor selection, catalyst regeneration, and system adjustments. The proposed method is intuitive and efficient and can be applied in the preparatory/operation stage. For the studied benzene hydrogenation process, the Plug Flow Reactor is suitable; the catalyst’s optimal service life is 2.08y, achieving 4.4 % and 4.8 % decreases in annual cost and energy demand/carbon emission by real-time adjustments.
Optimization of Solvent and Extractive Distillation Sequence Considering Its Integration with Reactor

Changfang Yin,Guilian Liu

DOI: https://doi.org/10.3390/pr9030565

IF: 3.5

2021-01-01

Processes

Abstract:The integration of reaction and extractive distillation system is beneficial for reducing the process cost. A systematic method is proposed to identify the optimal solvent, solvent-to-feed ratio, extractive distillation sequence and reactor operating conditions based on the integration of reactor and extractive distillation. The non-key component matrix method is used to generate the extractive distillation sequences. The proposed method can be used to evaluate different solvents, solvent-to-feed ratios, as well as the extractive distillation sequences; the optimal extractive distillation parameters corresponding to the minimum total annualized cost (TAC) can be identified considering different operating conditions. For the selective hydrogenation of benzene to cyclohexene process, the minimum total annualized cost of unit desired product, 4.01 $·kmol−1, is achieved when the reactor’s inlet temperature is 333 K, solvent N-Formylmorpholine and sequence S2 are employed, and the solvent-to-feed ratio is 4.
Numerical modelling of the operational effects on the thermochemical reactor performance

Cheng Zeng,Shuli Liu,Ashish Shukla,Liu Yang,Xiaojing Han,Yongliang Shen

DOI: https://doi.org/10.1016/j.enbuild.2020.110535

IF: 7.201

2021-01-01

Energy and Buildings

Abstract:<p>To increase the share of renewable energy in buildings, thermochemical energy storage stands out in the high energy storage density and long-term storage capability. However, it requires further investigation to improve the performance of the thermochemical reactor. As the research community has seen an increasing number of reactor designs, the reactor operational parameters are critical to the reactor performance. This study presents the effect of the essential parameters on the reactor performance through a validated numerical model. The study has found that the reactor charging performance is determined by the charging temperature, air flow rate, bed porosity, and the charging duration. The discharging performance is affected by the inlet air temperature, inlet air relative humidity, and material particle diameter. Suggestions have been given on the parameters according to the analysis. For instance, the inlet air temperature in discharging is suggested ranging from 7 °C to 15 °C. In discharging, the inlet air relative humidity is suggested at 40%. The reactor bed porosity should be above 0.4 to improve the mass transfer. A holistic control strategy should be given in future reactor studies considering the reactor status and the operating targets.</p>

energy & fuels,construction & building technology,engineering, civil
Integrated Design And Optimization Of Reactor-Distillation Sequence-Recycle-Heat Exchanger Network

Changfang Yin,Huifeng Sun,Donghui Lv,Guilian Liu

DOI: https://doi.org/10.1016/j.energy.2021.121796

IF: 9

2022-01-01

Energy

Abstract:In the chemical process, reactor and distillation sequence are interconnected by the reactor effluent and recycle streams, and affect the heat exchanger network (HEN). A systematic method is proposed for synthesizing and optimizing the Reactor-Distillation sequence-Recycle-HEN (RDRH) system. In this method, an improved partition method is used to identify all feasible distillation sequences; each distillation sequence is integrated with the reactor, the recycle and HEN. This method can identify the RDRH system with the minimum energy consumption and the corresponding key parameters efficiently. A styrene unit is studied by the proposed method, the results are in good agreement with those identified based on the rigorous simulation of Aspen Plus, and the relative errors are less than 5.5%. The proposed method can be applied in the preliminary design for targeting the optimal flowsheet and parameters, comparing catalysts, and can be extended to optimize the flowsheet in the whole life cycle. (c) 2021 Elsevier Ltd. All rights reserved.
Simulation and Optimization of A Full-Scale Carrousel Oxidation Ditch Plant for Municipal Wastewater Treatment

Wen-Ming Xie,Rui Zhang,Wen-Wei Li,Bing-Jie Ni,Fang,Guo-Ping Sheng,Han-Qing Yu,Jing Song,De-Zhi Le,Xue-Jun Bi,Chang-Qing Liu,Min Yang

DOI: https://doi.org/10.1016/j.bej.2011.04.010

IF: 3.9

2011-01-01

Biochemical Engineering Journal

Abstract:A full-scale Carrousel oxidation ditch wastewater treatment plant (WWTP) was simulated and optimized through integrating the activated sludge model 2d (ASM2d), support vector regression (SVR) and accelerating genetic algorithm (AGA). The ASM2d model after calibration and validation with the operating data was used to simulate the process. Operating parameters, including hydraulic retention times (HRTs) of anaerobic, anoxic and aerobic tanks, solids retention time (SRT) and internal recirculation ratio were subjected to optimization using SVR and AGA. The simulation results were normalized and SVR was employed to correlate the operating factors and the effluent quality. Then, the AGA approach was used to obtain the optimal operating conditions. The multiple-objective optimization with different weights indexes was adopted to achieve simultaneous nutrient removal. Compared with the present operating conditions, the HRT of the anoxic tank, the internal recirculation ratio and the SRT should be reduced, while the HRT of the aerobic tank should be prolonged to achieve better effluent quality. Such an integrated approach in this study offers an effective and useful tool to optimize the oxidation ditch process of WWTPs. (C) 2011 Elsevier B.V. All rights reserved.

Several optimization problems of chemical reactor

Production Optimization for Concentration and Volume-Limited Fed-Batch Reactors in Biochemical Processes

Comments on “optimal Use of Mixed Catalysts for Two Successive Chemical Reactions”

Dynamic optimization of operation of heat-integrated distillation column systems

Modeling and Optimization of Ethane Steam Cracking Process in An Industrial Tubular Reactor with Improved Reaction Scheme

Optimization of an industrial batch polycondensation reactor

Dynamic Optimization of Multivariable Endothermic Reaction in Cascade CSTR

Optimal Scheduling of the Multigrade Parallel Distillation Column System with a Continuous-Time Formulation

An Overview on Chemical Process Operation Optimization

Acrylonitrile Reactor On-Line Operation Optimization Software and Its Application

OPERATION OPTIMIZATION OF A PROPYLENE CHLOROHYDRIN REACTOR

Advances in methods of reactor network synthesis and optimizat ion

Optimization of Volatile Fatty Acid Production with Co-Substrate of Food Wastes and Dewatered Excess Sludge Using Response Surface Methodology

Graphical Optimization Method for Coupled Heat Exchanger Network and Reactor

Modelling and Operation Conditions Optimization of Ethylene Oxychlorination in Fluidized Bed Reactors

Optimization of chemical reactor feed by simulations based on a kinetic approach

Novel Methodology for Targeting the Optimal Reactor and Operating Parameters Based on the Chemical System’s Overall Performance Within Catalyst Lifecycle

Optimization of Solvent and Extractive Distillation Sequence Considering Its Integration with Reactor

Numerical modelling of the operational effects on the thermochemical reactor performance

Integrated Design And Optimization Of Reactor-Distillation Sequence-Recycle-Heat Exchanger Network

Simulation and Optimization of A Full-Scale Carrousel Oxidation Ditch Plant for Municipal Wastewater Treatment