Abstract:Sintering behaviour of ashes from combustion of coal and biomass blends was experimentally investigated with a focus on the effect of ash preparation method. Blends of a Chinese anthracite, Jincheng coal, and two biomass materials, a wheat straw and a pine sawdust, respectively, were subjected to three different ash preparation procedures, namely, a low temperature oxygen plasma ashing device operating at ca 150 degrees C, combustion in a Muffle furnace at 815 degrees C and in a drop tube furnace at 1500 degrees C. The resulting ash samples were then subjected to the sintering temperature measurement using a pressure-drop sintering device, morphological and mineralogical characterisation using scanning electron microscope (SEM) fitted with X-ray energy dispersive spectroscopy (EDS) and X-ray diffractometry analyser (XRD), respectively. For the same coal and biomass blends but different ash preparation methods, the sintering temperatures were always the lowest for the ash samples from the plasma ashing device and the highest from drop tube furnace. SEM imaging showed that the texture of ash samples from the plasma ashing device was irregular, loose and more fibrous, indicating little interactions among the different mineral and inorganic constituents in the individual fuels. The muffle furnace and drop tube furnace ashes were denser and more uniform in shape as the mineral matter and inorganics became fused together. In addition, the drop tube furnace ashes were mostly in spherical-shape, indicating ash melting had occurred during combustion. The XRD analysis revealed that different minerals were present in the ash samples due to different ash preparation temperatures, with high temperature minerals present in the drop tube furnace ash. Biomass addition in the blends lowered the sintering temperature of corresponding ash; the higher the proportion of biomass in the blend, the lower the ash sintering temperature regardless the ashing method. At the same biomass addition ratio, the ash sintering temperature of the blend with the wheat straw addition was lower than that with the pine sawdust addition, because the wheat straw had a higher K and Cl content but lower Ca than the pine sawdust. The EDS and XRD analyses confirmed that the ashes of coal/wheat straw blends contained more K-bearing minerals, while the ashes of the coal/pine sawdust contained more Ca and K-bearing minerals. Both Ca and K-bearing minerals reacted with other minerals in the ash to form low temperature eutectics, leading to the reduction of sintering temperatures of the coal and biomass blends. However, the melting points of the K-containing minerals are higher than the Ca-containing minerals, therefore, the sintering temperatures of ash with the wheat straw addition were lower than those with the pine sawdust addition. (C) 2016 Elsevier Ltd. All rights reserved.

The measuring and control of paper ash content

On-line measurement of ash content in paper

A New Sensor for Paper Basis-Weight and Ash-Content Measurements

Measurements of Quality Variables for an Industrial Rolling Mill Reheating Furnace (II)

Comprehensive Improving Technology for Air Leakage on Sintering System

Effect of Ash Preparation Method on the Sintering Characteristics of Ashes from Combustion of Coal and Biomass Blends

Experimental Study on the Sintering Characteristics of Biomass Ash

Assessment of COD discharge and regulation compliance for papermaking plants

RESEARCH & DEVELOPMENT ON MCA-BASED COAL ASH GAUGE

Study on Coal Ash Fusion Characteristics with TG-DSC Method

Mechanism of measuring ash with low-energy gamma rays for equal coal seam thickness

Measurement of cigarette combustion ash line width on the basis of full vision

Sintering Behavior Of Ash From Combustion Of Jincheng Coal And Pine Sawdust Blends

Intelligent Optimized Control System for Solvent Dewaxing Device

METERING & CONTROL SYSTEM FOR COATING FUEL IN SINTERING PROCESS

Design of Micro-Computer Controlling System for Batch Asphalt Mixing Equipment in Measurement and Gradation

The Online Correction of Gamma-ray Ash Monitor in Coal Preparation Plant

Analytic Study on Approach to Adiabatic Saturation Temperature and the Control Scheme for the Amount of Water Sprayed in the Semi-Dry FGD Process

Test device and method for simulating deposition of fly ash on heating surface

Ash Deposition Mechanism and Composition Distribution Characteristics in Oil-fired Boiler

Experimental measurement of the effective thermal conductivity of ash deposit for high sodium coal (Zhun Dong coal) in a 300 KW test furnace