Abstract:Infiltrated molten Al matrix by mechanical-pressure infiltration method into the ceramic scaffold prepared by freeze-drying technology could prepare dense lamellar Al matrix composites without damage of the biomimetic microstructure of the scaffold. However, the investigation of lamellar Al matrix composites prepared by freeze-drying and mechanical-pressure infiltration method has not been fully understood yet. In the present work, the Al2O3 scaffold with pearl layer structure was prepared by freezing-dry method, and eventually the lamellar Al(2)O(3)p/Al composite was fabricated by mechanical-pressure infiltration method. The Al matrix was infiltrated well into the large pores of the Al2O3 scaffold, and the lamellar structure of the Al2O3 was well preserved. The hardness of the lamellar Al(2)O(3)p/Al composite was isotropic in transvers and perpendicular directions. However, the compressive strengths of the lamellar Al(2)O(3)p/Al composite were significant anisotropic while the compressive strength in transvers direction was 127.7% higher than that in the perpendicular direction, indicating the integrality of the lamellae microstructure (especially the bridging layers). Due to the mismatched deformability, weak debonding was observed between Al and Al(2)O(3)p/Al layers in the fracture surface of the lamellar Al(2)O(3)p/Al composite. It indicates that the interfacial bonding between Al and Al(2)O(3)p/Al layers is rather strong, which is beneficial for higher strength in transvers direction but lead to lower strength in perpendicular direction.

Microstructure and properties of Al(2)O(3)sf/Al -1.5Mg composite manufactured by extrusion directly following liquid infiltration

MMCs with Controlled Non-Uniform Distribution of Submicrometre Al2O3particles in 6061 Aluminium Alloy Matrix

Microstructure characterization and mechanical properties of Al-matrix composites reinforced by artificially-cultured diatom frustules

Al2o3 Particles Reinforced Aluminium Matrix Composite Fabricated By Pressureless Infiltration Technique

Interface Reaction and Thermodynamic Analysis on Al2o3-Sio2(Sf)/Az91d Composite

Microstructure and Mechanical Properties of Al/Al4C3/Al2O3 Composite

Microstructure and Mechanical Properties of High Strength Al2o3p/6061al Composites

Fabrication and Mechanical Properties of Particle Dispersed Al-Al2O3 Composite Materials.

Interface microstructure and mechanical property of (Al2O3-SiO2)sf/AZ91D composite

Microstructure and Compressive Behavior of Lamellar Al2O3p/Al Composite Prepared by Freeze-Drying and Mechanical-Pressure Infiltration Method

Co-continuous Al/Al2O3 composite produced by liquid displacement reaction: Relationship between microstructure and mechanical behavior

Microstructure, Interface and Fabricating Process of Al_2O_3-SiO_2/AZ91D Composites Prepared by Squeeze Infiltration

Tensile deformation behavior of a sub-micrometer Al2O3/6061Al composite

Microstructure Evolution and Mechanical Properties of Ni3al/Al2o3 Composite During Self-Propagation High-Temperature Synthesis and Hot Extrusion

Investigation of Phase Composition and Microstructure of the FeAl/Al<sub>2</sub>O<sub>3</sub> Composites Fabricated by Mechanical Alloying and Hot-Pressing Process

Interface Investigations of Alumina and Aluminosilicate Short-Fiber-reinforced Aluminum-Alloy Composites

Microstructure and mechanical properties of Al2O3/Al2O3 composite densified through a slurry infiltration and sintering process

Microstructure evolution and mechanical properties of Al-Al2O3 composites fabricated by selective laser melting

Influence of Cu content on interfacial microstructure of Al2O3-SiO2 fiber reinforced Al matrix composites

An Al-Al interpenetrating-phase composite by 3D printing and hot extrusion

Influence of Cu content on interfacial structure and mechanical properties of 3Al2O32SiO2 fiber reinforced Al matrix composites