Abstract:NUREG report CR-6909 [1] proposed in 2007 new rules for evaluating environmental effects in fatigue analyses of new reactors components. These new rules, based on simple correlations, consider that Fen penalty factors (ratio of fatigue life in air at room temperature to that in water at service temperature) are mainly function of strain rate, temperature, sulfur content and dissolved oxygen concentrations. In order to evaluate the conservatisms included in the NUREG report CR-6909, discriminating Low Cycle Fatigue (LCF) tests were performed on a 304L austenitic stainless steel in PWR environment using various modified loading signals deduced from a representative loading strain history as close as possible to actual transients. Using the strain rate integral method recommended in the NUREG/CR-6909, the expected Fen penalty factors evaluated for each modified representative loading signal was close to 6, while the experimental Fen penalty factors measured were strongly dependent of the shape of the loading signals. Experimental Fen penalty factors obtained for the various modified loading signals vary from ∼ 1.5 to ∼ 4. These discriminating LCF tests performed on polished specimens demonstrate that the detailed strain integral method cannot correctly predict the actual environmental effects for the various shapes of loading signals deduced from a representative loading strain history. Other LCF tests were also performed for various constant strain amplitudes using fully reverse triangle signals for comparison purpose with tests performed by other laboratories. It appears that, contrary to published results, environmental effects decrease when the strain amplitude decreases from 0.6% until 0.2%. In the case of the strain amplitude of 0.6%, the Fen penalty factor formulation proposed in the NUREG report CR-6909 is accurate while, for lower strain amplitude of 0.2%, the Fen penalty factor formulation is very severe. It appears that the application of the NUREG/CR-6909 including the Fen model proposed by ANL (Argonne National Laboratory) for austenitic stainless steel provides excessive margins compared to penalty factors as observed experimentally. From this experimental program, conservatisms included in the NUREG/CR-6909 methodology appear to be excessive and can lead to fatigue design issues.

Environmental Fatigue Analysis of a U Seal in Pressure Vessel under Simulated LWR Operation

FEA-Based Failure Analysis of a UHP Chamber for Simulation of Deep Sea Conditions

Fatigue Failure Analysis and Simulation Calculation of Submarine Suspended Pipelines

Assessment of Environmental Fatigue in Nuclear Power Plants: A Comparative Analysis of the Effects of Plasticity Correction

Effects of Loading Factors on Environmental Fatigue Behavior of Low-Alloy Pressure Vessel Steels in Simulated Bwr Water

Environmental Fatigue Correction Factor Model for Domestic Nuclear-Grade Low-Alloy Steel

Corrosion Fatigue Mechanism of Nuclear-Grade Low Alloy Steel in High Temperature Pressurized Water and Its Environmental Fatigue Design Model

Prediction of long-term fatigue life of CFRP composite hydrogen storage vessel based on micromechanics of failure

Effect of Loading Signal Shape and of Surface Finish on the Low Cycle Fatigue Behavior of 304L Stainless Steel in PWR Environment

A Quasi Time-Domain Method for Fatigue Analysis of Reactor Pressure Vessels in Floating Nuclear Power Plants in Marine Environments

A Study On Performance Of O-Shaped Seal Ring In Lwd Device Using Finite Element Analysis

Comparative Study of Flange-To-Seal Contact Couplings with Bolt Relaxation under Creep Condition

Analysis on High Temperature Strength and Sealing Behavior of U-type Seal in Steam Turbine Valves

Corrosion Fatigue Behavior of 316LN Stainless Steel Hollow Specimen in High-Temperature Pressurized Water

CORROSION FATIGUE OF NUCLEAR-GRADE STAIN- LESS STEEL IN HIGH TEMPERATURE WATER AND ITS ENVIRONMENTAL FATIGUE DESIGN MODEL

Influence of Temperature and Pressure Fluctuations on the Mechanical Behavior of A Seal Structure in Steam Valve under In-Service Conditions

ANSYS Interference Fit Analysis of Mechanical Seals in Reactor Coolant Pumps

Sealing performance assessments of PTFE rotary lip seals based on the elasto-hydrodynamic analysis with the modified archard wear model

A Two-Phase Methodology to Predict Fac Wear Sites in the Piping System of A Bwr

A REVIEW OF CORROSION FATIGUE OF STEELS FOR LWR PLANT IN HIGH TEMPERATURE AND HIGH PRESSURE WATER

Stress Concentration Factor and Fatigue Analysis of a Lateral Nozzle with Local Wall Thinning