Abstract:Recently, sodium ion batteries (NIBs) gained increasing attention, because of its abundant reserves and relatively even geological distribution. However, the development of NIBs is greatly hampered because of the lack of appropriate active materials for both cathodes and anodes. Since the Na ion is ca. 55% larger than the Li ion, finding suitable host materials with sufficiently large interstitial space to accommodate sodium ions and to allow reversible and rapid ion insertion and extraction is very difficult. NASICON-type Na3V2(PO4)3 has recently been considered as a prospective cathode material for NIBs, because of its highly covalent 3D framework crystalline structure, high energy density (~400 Wh/kg) and good thermal stability. For anode materials, disordered carbon is particularly attractive because of their large interlayer distance and disordered structure that could accommodate sodium ions. Here, we briefly present porous carbon based electrodes for NIBs with excellent rate performance: (1) Carbon-coated nanosized Na3V2(PO4)3 embedded in the porous carbon matrix (abbreviated as CC-NVP@PCM); (2) Nitrogen-doped activated porous carbon fibers (ACFs); (3)Flexible free-standing porous carbon nanofibers (P-CNFs) with three-dimensional (3D) interconnected structure. The CC-NVP@PCM was prepared by using a facile soft-chemistry based method with post heat-treatment. It shows high rate performance (44 mAhg-1at 200C ). This ultrahigh rate performance is comparable to that of supercapacitor, but with much higher energy density. The ACFs were synthesized by pyrolysis of Ppy nanofiber precursor. It shows excellent capacity retention and extraordinary rate performance. The reversible capacity at 0.05 Ag-1 is 296 mAhg-1 and could still maintain as 72 mAg-1 at a current of 10 Ag-1. In case of the P-CNFs electrode prepared by electrospinning, it delivers a reversible capacity of 266 mAh.g-1 after 100 cycles at 0.2C, corresponding to 80.3 % of the initial charge capacity. When cycled at a current density as high as 500 mAg-1 (2C), it still delivers a reversible capacity of ~140 mAh.g-1after 1000 cycles. The improvement of electrochemical performance of these porous carbon based electrodes for NIBs is attributed to the special design and porous structure, which confined a variety of advantages: hierarchical porous channels enabling short transport length for ions and electrons, carbon coated structure resulting in low resistances, good mechanical properties leading to the excellent morphology stability.

Free-standing and Binder-Free Sodium-Ion Electrodes with Ultralong Cycle Life and High Rate Performance Based on Porous Carbon Nanofibers.

Engineering Capacitive Contribution in Nitrogen-Doped Carbon Nanofiber Films Enabling High Performance Sodium Storage

High rate and long cycle life porous carbon nanofiber paper anodes for potassium-ion batteries

In Situ Transmission Electron Microscopy Study of Electrochemical Sodiation and Potassiation of Carbon Nanofibers

Electrodes for Sodium-Ion Batteries with Excellent Rate Performance Using Porous Carbon Networks

A facile strategy toward sodium-ion batteries with ultra-long cycle life and high initial Coulombic Efficiency: Free-standing porous carbon nanofiber film derived from bacterial cellulose

Na3MnTi(PO4)3/C Nanofiber Free-Standing Electrode for Long-Cycling-Life Sodium-Ion Batteries

Enhanced Silicon Diphosphide-Carbon Composite Anode for Long-Cycle, High-Efficient Sodium Ion Batteries

Flexible carbon nanofibers with multichannel and porous structure as freestanding anode for excellent sodium storage

A superior sodium-ion anode material from PAN/Lignin-derived carbon nanofibers with inter-connected structure prepared through phosphoric acid induced cross-linking

Phytic acid-derived Co2P/N-doped carbon nanofibers as flexible free-standing anode for high performance lithium/sodium ion batteries

Flexible and crosslinking electrospun porous carbon nanofiber membranes as freestanding binder-free anodes for lithium-ion batteries

Ni2P nanoparticle-incorporated reduced graphene oxide & carbon nanotubes to form flexible free-standing intertwining network film anodes for long-life sodium-ion storage

Free-standing ZnSe-CoFe@CNT/CNF heterostructure nanofibers as an ultra-long lifespan and high-rate anode for flexible lithium ion and sodium ion batteries

Free-Standing and Binder-Free Sodium-Ion Electrodes Based on Carbon-Nanotube Decorated Li4ti5o12 Nanoparticles Embedded in Carbon Nanofibers

Architecting Braided Porous Carbon Fibers Based on High‐Density Catalytic Crystal Planes to Achieve Highly Reversible Sodium‐Ion Storage

Sodium/Potassium‐Ion Batteries: Boosting the Rate Capability and Cycle Life by Combining Morphology, Defect and Structure Engineering

Ultrafine ZnSe Encapsulated in Nitrogen-Doped Porous Carbon Nanofibers for Superior Na-Ion Batteries with a Long Lifespan and Low-Temperature Performance

CoS nanoparticle encapsulated S-doped carbon nanofiber/nanotube hybrid grown on exfoliated graphite for long-lifespan and high-rate potassium ion batteries

Free-Standing N-Doped Porous Carbon Fiber Membrane Derived From Zn–MOF-74: Synthesis and Application as Anode for Sodium-Ion Battery With an Excellent Performance

Electrospun Na4Fe3(PO4)2(P2O7) nanofibers as free-standing cathodes for ultralong-life and high-rate sodium-ion batteries