Abstract:Solid oxide fuel cell (SOFC) is an energy conversion device that converts chemical energy in fuels into electric energy directly with the advantages of high efficient, clean, and wide fuel adaptability. Most hydrocarbons such as natural gas, ethane and bio-oil can be used as fuels in SOFC. When a hydrocarbon fuel, such as methane (CH4), is directly used for IT-SOFCs without prereforming by adding oxygen, steam or carbon dioxide, it is electrochemically oxidized on the triple-phase boundaries (TPB) with a strong tendency of carbon deposition in the traditional Ni-based anode. In this paper, we introduce an extra internal reforming layer on the surface of anode-support. The layer of a LaCrO3 based perovskite with exsolved Ni nanoparticles catalyst (La0.6Sr0.2Cr0.85Ni0.15O3 showed high stability in reducing atmosphere and excellent catalytic performance. Based on this, two types of anode-supported cell are fabricated by tape casting, screen printing and sintering processes. The first one is a conventional anode supported cell with a configuration of Ni-GDC/GDC/GDC-LSCF (cell 1); and the other contains a reforming layer mixed with La0.6Sr0.2Cr0.85Ni0.15O3 and SDC which was a well coking resistant promoters (cell 2). When CH4–CO2 was used as the fuel, which was supposed to yield syngas with the H2–CO ratio close to unity, the polarization resistance of the cell 1 reach at 0.247 Ω cm2 whereas the value of cell 2 is 0.082Ω cm2 at 750 °C. These results implied that both the physical and the chemical properties of the TPB have been altered drastically during internal dry reforming since that Ni-based anode show poor catalytic performance in reforming and are prone to coking. Consequently, the maximum power density for cell 1 was 470 mW cm-2 and the cell suffered from degradations during a 1 h galvanostatic operation at 1 A cm-2. The performances of the cell 2 are significantly increased above the level of the cell 1, demonstrating a peak power density at 929 mW cm-2 at 750 °C and a stable cell voltage at 1 A cm-2 and 750 °C for 48 h. Carbon deposition in the anode region of the tested cell 2 is not detected, as the La0.6Sr0.2Cr0.85Ni0.15O3 is a more active and stable catalyst than the Ni-based anode-support for dry reforming. Finally we demonstrated the strong interaction between the exsolved nanoparticles and the substrate could prevent coking deposition and proposed a promising configuration of double-layer anode for solid oxide fuel cells with on-cell reforming. Figure 1

Carbon-tolerant solid oxide fuel cells using NiTiO3 as an anode internal reforming layer

A Robust Carbon Tolerant Anode for Solid Oxide Fuel Cells

Novel In-Situ MgO Nano-Layer Decorated Carbon-Tolerant Anode for Solid Oxide Fuel Cells

Coking-resistant Ce0.8Ni0.2O2-δ Internal Reforming Layer for Direct Methane Solid Oxide Fuel Cells

Study on a Novel Double-Layer Anode for Solid Oxide Fuel Cells Based on CO2 Dry Reforming of Methane

Enhance coking tolerance of high-performance direct carbon dioxide-methane solid oxide fuel cells with an additional internal reforming catalyst

A Ruddlesden–Popper Oxide As a Carbon Dioxide Tolerant Cathode for Solid Oxide Fuel Cells That Operate at Intermediate Temperatures

Transparent conductive oxide type materials as the anode of solid oxide fuel cells at a reduced temperature

A Rational Design of FeNi Alloy Nanoparticles and Carbonate-Decorated Perovskite As a Highly Active and Coke-Resistant Anode for Solid Oxide Fuel Cells

Performance and Optimization of Ni/3 Mol% Y2O3-ZrO2 Anode Supported SOFC

Enhanced methane steam reforming activity and electrochemical performance of Ni0.9Fe0.1-supported solid oxide fuel cells with infiltrated Ni-TiO2 particles

Tailoring the solid oxide fuel cell anode support composition and microstructure for low‐temperature applications

A Highly Coking-Resistant Solid Oxide Fuel Cell with a Nickel Doped Ceria: Ce1−xNixO2−y Reformation Layer

Electrochemical performance and redox stability of solid oxide fuel cells supported on dual-layered anodes of Ni-YSZ cermet and Ni–Fe alloy

A high-performance Ni-CeO2/Ni/Ni-Y2O3·ZrO2 three-layer anode for direct iso-octane feeding of solid oxide fuel cells

Nickel-iron nanoparticles encapsulated in carbon nanotubes prepared from waste plastics for low-temperature solid oxide fuel cells

Enhanced Performance of Solid Oxide Fuel Cells with Ni/CeO2 Modified La0.75Sr0.25Cr0.5Mn0.5O3− Anodes

Carbon-resistant Ni-YSZ/Cu-CeO2-YSZ dual-layer hollow fiber anode for micro tubular solid oxide fuel cell

Fabrication and Study on Ni1−xFexO-YSZ Anodes for Intermediate Temperature Anode-Supported Solid Oxide Fuel Cells

Nano-Structured Anodes of Solid Oxide Fuel Cells

An Efficient Construction of Nano-Interfaces for Excellent Coking Tolerance of Cermet Anodes