Abstract:In this work, investigations on detailed heat transfer characteristics over an endwall surface for a turbine nozzle guide vane were conducted. Experiments were performed in a linear cascade test facility using infrared thermography technique over a range of engine-representative inlet Reynolds numbers from 1.40×10 to 4.20×10 with a high free-stream turbulence level. Accordingly, numerical simulations were carried out to be compared and complementary to the measurements. Besides, in order to demonstrate the effects of exit Mach number on endwall heat transfer in isolation, simulations were also conducted at various vane exit Mach numbers ranging from 0.616 to 1.016 while the inlet Reynolds number was kept constant at the design point of Rein=3.46×10. High heat transfer coefficients were observed in the leading edge region and near and downstream of the throat areas. Increasing inlet Reynolds number could result in higher heat transfer level on the endwall surface. Numerical results agreed well with the measurements, and the predicted flow field in the vane passage highlighted the links between the heat transfer patterns and the flow structures near the endwall. The computational results also revealed that vane exit Mach number mainly dominated the heat transfer in the aft part of the endwall and higher Mach numbers led to lower heat transfer coefficients. INTRODUCTION Great efforts have been devoted to thermal analysis and designs of gas turbine stages in order to increase the cycle efficiency of gas turbines continuously. In particular, though it is a technical challenge to measure the thermal loads in a real engine vane passage, accurate knowledge of local thermal load patterns under engine-representative conditions is critical for engine designers to validate and optimize the cooling schemes and further to ensure the durability and reliability of the designs. This demonstrates the importance of providing accurate experimental data related to each specific configuration for engine designer. The flow inside a vane passage is characterized by highly three-dimensional and complex flow structures due to the generation of secondary flows and the radial and circumferential pressure gradient, which have strong impacts on flow development and heat transfer on the vane endwalls. Previously, many studies documented the influence of those vortical structures on endwall heat transfer and the detailed reviews regarding the flow and heat transfer issues near the endwall of a vane passage were made by Chyu (2001) and Simon et al. (2006). To date, the relationship between the secondary flow and heat transfer as well as cooling is attracting constant attention over the years. Blair (1974) could be the pioneer to detect the heat transfer over endwalls and discovered the highly strong links to the vortical structures evolving within the passage. Later, the links was confirmed by the work of Takeishi et al. (1990). With the deep understanding of the secondary flow mechanism in the vane passage, Friedrich (1997) summarized the common understanding of high heat transfer coefficient regions on the endwall based on the existing experimental work. Those regions are 1) the leading edge where the horseshoe vortex (HV) forms, 2) the suction surface shoulder where the lift-off line of the suction side of the HV and the dominated passage vortex meet, 3) the pressure surface corner where the boundary layer is thin due

Pressure and Heat Transfer Measurement of Vane Surface in Short Duration Wind Tunnel

Effects of inlet turbulence intensity on wall heat transfer in a turbine guide vane

A numerical study on vane heat transfer characteristic at low Reynolds number conditions

Heat transfer characteristic of a fully cooled turbine vane

Parametric Influence on Convective Heat Transfer for an Outlet Guide Vane

Measurements of Heat Transfer and Pressure in a Trailing Edge Cavity of a Turbine Blade

Experimental invesitigations and numerical analysis on heat transfer of a ngv endwall at engine representative reynolds and mach numbers

Experimental Study on the Forced Convection Heat Transfer Characteristics of Air Flow Across a Cylinder under Low Vacuum Pressures

Effect of Mass Flow Ratios on the Conjugate Heat Transfer of a Metal Turbine Vane at Medium Temperature

Mean pressure distributions around a circular cylinder in the branch of a T-junction with/without vanes

Influence Of Hot Streak/Airfoil Count Ratios On High Pressure Stage Of A Vaneless Counter-Rotating Turbine

Influence of Non-Uniform Inflow Swirl and Hot Streak on Turbine Vane

Experimental Study on the Aerodynamic Performance of Variable Geometry Low-Pressure Turbine Adjustable Guide Vanes

Heat Transfer Measurements of a Turbine Endwall with Engine-Representative Freestream Turbulence and Inlet Swirl

Experimental Measurements and Numerical Investigations on the Aerodynamic Performance and Internal Flow Fields of Tangential Admission Volutes for Steam Turbines

Effects of Freestream Turbulence Intensity, Turbulence Length Scale, and Exit Reynolds Number on Vane Endwall Secondary Flow and Heat Transfer in a Transonic Turbine Cascade

Conjugate Heat Transfer Measurements and Predictions for the Vane Endwall of a High-Pressure Turbine with Upstream Purge Flow

Measurements of Detailed Heat Transfer Characteristics on a High-Pressure Turbine Vane Endwall with Coolant Injection

Experimental Investigation of Heat Transfer and Pressure Drop in a Two-Pass Internal Coolant Passages of Gas Turbine Airfoil

Numerical Study on Flow and Heat Transfer of a Cooled First Stage Vane of a Gas Turbine

Effect Of Radiative Heat Transfer Factor On The Temperature Distribution Of A First Stage Vane