An ultrasonic driving principle using friction reduction

Xiaolong Lu,Junhui Hu,Qi Zhang,Lin Yang,Chunsheng Zhao,Piotr E. Vasiljev

DOI: https://doi.org/10.1016/j.sna.2013.05.025

2013-01-01

Abstract:•An ultrasonic driving principle based on the friction reduction effect was proposed.•A linear ultrasonic motor based on this principle was designed, fabricated and characterized.•The principle was confirmed by the prototype motor.

What problem does this paper attempt to address?

Experimental Investigation on Friction Characteristics of Ultrasonic Motor

王文浩,郭吉丰,金龙,曲建俊,王光庆

DOI: https://doi.org/10.16078/j.tribology.2010.02.019

2010-01-01

Tribology

Abstract:Ultrasonic motor is an unconventional motor driven by (notional force and high frequency vibration based on the principle of inverse piezoelectric effect. The high frequency vibration and minor amplitude between the stator and rotor have its own characteristics at friction interface, which is different from the traditional interface. The characteristics have significant effect on conversion efficiency, motor's lifetime and the choice of frictional material. This paper presented the dynamic friction coefficient in normal, standing wave and the traveling wave measured by self-manufactured experiment structure. The influences of the relative speed, preload and temperature's impact on friction coefficient between the stator and rotor were analyzed. The relationship between friction coefficient and preload was explained from friction binomial and elastoplasticity contact state of the interface. The paper also explained the effect of friction reduction in the presence of ultrasonic vibrations both from standing wave and traveling wave. The impact of temperature on friction coefficient was also tested. Finally, this paper revealed a friction model for ultrasonic motor. The friction reduction for ultrasonic motor was a foundmental work, which was useful for design, modeling and controlling of ultrasonic motor.
Study on Antifriction Effect of Ultrasonic Vibration in Ultrasonic Driving

曲建俊,姜开利,张凯,周铁英

DOI: https://doi.org/10.3321/j.issn:0371-0025.2001.06.003

2001-01-01

Acta Acustica

Abstract:This paper describes a theoretical study, using dynamic principle, about the influence of the ultrasonic vibration on the frictional properties of ultrasonic driving. Ultrasonic vibration of stator surface points at the contact region of stator and rotor in ultrasonic motor(USM) is resolved into horizontal and vertical vibration and the effects of two direction vibration on USM driving are analyzed. It is proposed that the horizontal vibration produces friction driving force and vertical vibration affects horizontal driving effect. The role of vertical ultrasonic vibration of stator surface points in USM is equivalent to the role of ultrasonic vibration being perpendicular to sliding direction in common sliding test. The reasons are revealed that the vertical ultrasonic vibration results in decrease of sliding friction coefficient in ultrasonic driving. An experiment is performed to verify the anti-friction effect of vertical ultrasonic vibration.Experimental results show reasonable correlation betw een theory and experiments.
A Method to Change Frictional Characteristics Based on Ultrasonic Micro Driving Technique

CHEN Weishan,ZHANG Fan,LIU Junkao

DOI: https://doi.org/10.3321/j.issn:0371-0025.2006.05.009

2006-01-01

Acta Acustica

Abstract:In order to reduce friction force and eliminate stick-slip phenomenon of a mechanic system at a low velocity, a method based on the ultrasonic micro driving technique to change the frictional characteristics is proposed. Exciting clockwise and anticlockwise microscopic elliptical motion of driving points on the ultrasonic actuator's two longitudinal bolt-clamped vibrators will generate ultrasonic lubrication action; furthermore, the friction can be actively controlled by adjusting the vibrators' vibrating amplitude. An experimental installation for friction control is designed using aerostatic guide, force sensors and a low speed moment motor. Fuzzy control theory is applied into this system. The experiments indicate the friction force has been reduced largely and the motion of the experimental system is stable. The friction coefficient is only about 0.0053 when the total mass of the ultrasonic actuator and load is 3.8 kg and the motor's driving velocity is 0.5 mm/s.
ANTIFRICTION MECHANISM OF ULTRASONIC VIBRATION BASED ON ULTRASONIC MICRO DRIVING

Luo Yunxia,Qu Jianjun,Qi Yulin

DOI: https://doi.org/10.3321/j.issn:0577-6686.2001.05.012

IF: 2.964

2001-01-01

Chinese Journal of Mechanical Engineering

Abstract:Ultrasonic vibration of stator surface points at the contact region of stator and rotor in ultrasonic motor(USM) is resolved into horizontal and vertical vibration respectively. The effects of the two vibration on the drive properties of USM are analyzed.It is proposed that the horizontal vibration produces friction driving force and the vertical vibration affects this process.The action of vertical ultrasonic vibration is equivalent to that of ultrasonic vibration being perpendicular to sliding direction in common sliding test. The reasons are that the vertical ultrasonic vibration results in decrease of sliding friction coefficient in ultrasonic drive.
Experiment Study on Friction Reduction of Ultrasonic Vibration Based on Traveling Wave Ultrasonic Motor

QU Jian-jun,TIAN Xiu,SUN Feng-yan

DOI: https://doi.org/10.3321/j.issn:1004-0595.2007.01.016

2007-01-01

Tribology

Abstract:A geometric model of friction reduction of ultrasonic vibration based on traveling wave ultrasonic motor(TWUSM) is presented.Three driving conditions were adopted to drive the rotor of TWUSM to simulate the frictional driving characteristics of the TWUSM,which was driven by electromagnetic motor,by electromagnetic motor combining with one phase standing ultrasonic wave,and by TWUSM respectively.The experimental rig was used to simulate the friction characteristics of the TWUSM.A conception of friction coefficient reduction rate of ultrasonic vibration was introduced.Effects of the speed of electromagnetic motor,pre-load,exciting voltage and friction materials on friction coefficient of the friction couple of stator and rotor are experimentally investigated respectively.The phenomena of friction reduction in ultrasonic drive was obvious at high relative sliding speed,small pre-load,and large vibration amplitude of ultrasonic vibration.
Analysis on friction driving of linear ultrasonic motor with in-plane bending and longitudinal mode

Wan Zhijian,Hu Hong

2014-01-01

Abstract:The friction driving principle of ultrasonic motors is a complex issue. In this paper, tangential motion and normal motion of the particle in the drive-foot of the stator are analyzed. Equal speed points (ESPs) are defined as where the transverse velocity of the particle is equal to the velocity of the slider. The elliptical arc contacted with the slider is divided by ESPs into the driving-arc and hindering-arc. When the motor works, the center of the stator mass vibrates as the longitudinal vibration of the stator. Force applied to the end of the stator is not a constant value because of this vibration, and the slider is driven intermittently by the stator. Friction between the slider and stator is influenced by factors such as preloading, stiffness of materials, or stator vibration. The analysis on driving and the motor's friction can also provide a reference for ultrasonic motors.
Research Progresses in Friction Material for Ultrasonic Motor

QU Jian-jun,WANG Yan-li

DOI: https://doi.org/10.16078/j.tribology.2010.05.014

2010-01-01

Tribology

Abstract:Ultrasonic motor is a new type of motor which is driven by friction force generated at the interface between the rotor and the stator.Development and applications of ultrasonic motor largely rely on the performance of friction material.The research progress and basic demand of friction material for ultrasonic motor in home and abroad in recent years are discussed.Based on drive mechanism and characteristics of ultrasonic motor,the special demand of friction material should be achieved primarily from in three aspects,i.e.tribology,contact mechanics and material.The three aspects are specified as good tribological properties,proper contact deformation and proper structrual properties.Finally,according to the current problems of friction material for ultrasonic motor,four important topics are proposed.The topics are establishment of better contact model of ultrasonic motor,development of several kinds of friction materials for various environments,development of customized testing method and experimental equipment for friction material and setup method of life prediction.
An Equivalent Wear Method Of Friction Material For Ultrasonic Motor

Yanli Wang,JianJun Qu,JianChun Li,Xiu Tian

DOI: https://doi.org/10.1109/SPAWDA.2011.6167258

2011-01-01

Abstract:As one of key materials for improving the performance of ultrasonic motor, the wear of friction material plays an important role in contact friction properties and output performance of ultrasonic motors. However, the wear loss of friction material is small in the friction system of ultrasonic motor. If effects of wear of friction material on properties of ultrasonic motor studied with a real motor, the experiment process were time-consuming and low efficiency and influenced by lots of known or unknown factors. In this paper, based on operation principle and wear characteristics of ultrasonic motor, an equivalent wear experimental method which using reduction of thickness of friction material equivalent to wear of friction material was proposed. And the relationships between wear of friction material and performance of ultrasonic motor were established. Validity of the method was carried out on one 60 traveling wave ultrasonic motor. This research could provide a new method for studying performance and life of ultrasonic motor.
Driving characteristics of ultrasonic motor with different application mode of friction material

Yanli Wang,Jianjun Qu,Ningning Zhou

DOI: https://doi.org/10.1109/SPAWDA.2009.5428938

2009-01-01

Abstract:Friction material is one of the most important parts for ultrasonic motor. The characteristics of ultrasonic motor were affected directly by application modes of friction material. Two friction couples were prepared to simulate the contact behavior on two traveling wave ultrasonic motors. One friction couple is composed of rotor with friction material layer and metal stator; the other friction pair is composed of metal rotor and stator with friction material layer. Impedance characteristics of the stator were measured by impedance analyzer. Based on the two traveling wave ultrasonic motors, the variations of friction drive and wear properties of the two ultrasonic motors were studied. The pre and post surface morphology and surface roughness of contact interface of the two friction couples were investigated by metalloscope and JB-4C precision roughness instrument, respectively. The wear mechanism of contact interface was analyzed. The results showed that the resonance frequency of stator with friction material layer decreases slightly. The motor with friction material layer stator obtains bigger stall torque. Ploughing wear characteristic was the dominant wear mechanism and wear of contact interface of the motor with friction material layer rotor was more severe than the motor with friction material layer stator.
Effect of Application Mode of Friction Material on Driving Characteristics of Ultrasonic Motor

WANG Yan-li,QU Jian-jun,TIAN Xiu

DOI: https://doi.org/10.16078/j.tribology.2010.04.017

2010-01-01

Abstract:Friction material is one of the most important parts in ultrasonic motor. Its application modes affect directly the characteristics of ultrasonic motor. Using two traveling wave ultrasonic motors which the friction material was applied on rotor and stator, respectively, then the rotor and stator were matched with their corresponding stator and rotor to simulate the contact behavior of ultrasonic motor. The variations of load and wear properties of ultrasonic motor with the application modes of friction material were studied. Impedance characteristics of the stator were measured by impedance analyzer before and post applying on friction material layer. The unworn and worn surface morphologies and surface roughness of contact surfaces of the two ultrasonic motors were studied by metalloscope and JB-4C precision roughness instrument. The wear mechanism was analyzed. The results showed that resonance frequency of stator with friction material on decreased slightly. The motor with friction material applied on stator obtained higher stall torque at two ultrasonic motors without loading at same speed. Polishing wear was the dominant mechanism of the stator with friction material, while ploughing wear was the dominant mechanism of the rotor with friction material.
Study of rotary ultrasonic vibration anti-friction experimental mechanism

Zeng,Jun Li,Guangming Cheng,Zhigang Yang

1998-01-01

Abstract:The relation between ultrasonic vibration and anti-friction was analyzed preliminarily. A rotary ultrasonic vibration anti-friction experimental mechanism was developed. The relations between input voltage and system frictional force moment of the experimental mechanism under different vibration frequency were obtained. It lays the foundation for the further study.
Effects of Wear of Friction Material on Performance of Ultrasonic Motor

Jianjun Qu,Wenfeng Guo,Yanli Wang

DOI: https://doi.org/10.1177/1350650112463530

2012-01-01

Abstract:Friction material is one of the key components in an ultrasonic motor. The wear of the material affects the contact friction and output performance of the motor. A method which utilizes the equivalent wear of friction material to simulate the wear during operation is proposed based on the wear characteristics of the ultrasonic motor's contact interface. A relationship between wear and performances of the ultrasonic motor is constructed. The influences of wear on output performance, friction coefficient of the contact interface, and wear morphology are researched in the experiments. According to the experiment's results, with wear of friction material ( decreasing thickness), the output performance of the ultrasonic motor presents a downward trend, the friction coefficient between contact interfaces decreases gradually, the friction-reducing ratio between contact interfaces increases gradually, and the wear between contact interfaces decreases. The results are helpful to understand operating performance, design, and select friction material of ultrasonic motor.
Gradient Design Model of Contact Interface for Ultrasonic Motor

曲建俊,王彦利,周宁宁

DOI: https://doi.org/10.3901/jme.2010.17.073

2010-01-01

Journal of Mechanical Engineering

Abstract:Ultrasonic motor is a new type of motor driven by friction force between the contact interface of rotor and stator. Friction material is an important part of contact interface. Its design and wear control are key problems for ultrasonic motor. A simplified model of ultrasonic motor is established. Effect of wear of friction material on contact parameters and driving friction force is studied. The properties that worn friction material should have are obtained by keeping stable contact width between rotor and stator. Design principle and theoretical structure model of gradient friction material for ultrasonic motor are proposed. The simulation analysis shows that normal elastic modulus of friction material pasted on rotor should gradually decline from the extenior to the interior. This type of friction material can maintain the output properties and increase performance lifetime of ultrasonic motor. And a new field is opened up for choosing and reasearching friction material for ultrasonic motor.
Contact Process and Friction Analysis of Linear Ultrasonic Motor

Hai XU,Chun-sheng ZHAO

DOI: https://doi.org/10.3969/j.issn.1005-2615.2005.02.003

2005-01-01

Abstract:The contact process and the friction mechanism of a liner ultrasonic motor are studied. By simplifying friction interface as distributed springs and analyzing positions of the contact point and the equal-velocity point, the contact area of stator and friction interface can be parted as driving area and holding area. The relationship between the motor velocity and its export thrust is derived. In addition, simulation models in different distances of the motor stator and its friction interface are discussed. Output characteristics of the friction interface are analyzed by using this model. Simulation results show that the distance between the motor stator and the friction interface has a prominent effect on mechanism characteristics of the motor.
The Measurement on Vibration Friction Coefficient of Ultrasonic Motor

J. Y. Liew,Y. Chen,T. Y. Zhou

DOI: https://doi.org/10.1109/ultsym.2008.0037

2008-01-01

Abstract:An ultrasonic motor (USM) of the friction type is driven by the friction force between the stator and the rotor. However the classical Coulomb friction law can not be used to explain the driven mechanism of an ultrasonic motor under the condition of high frequency vibration between the stator and the rotor. In our early study[1], a vibration friction model was offered to explain a phenomenon in an experiment of an ultrasonic motor, in which the friction coefficient was considered as a function of the vibration amplitude. In this paper, we show some experimental results to verify our vibration friction model. The vibration amplitude of the stator is measured by using a laser vibrometer, and the results show that it is proportional to the input voltage. The tangential friction force between the stator and the rotor is measured by changing the input voltages under various normal pre-load. The friction coefficient is calculated according to its definition, namely the tangential friction force divide by the normal force. With the increasing of the input voltage or says the amplitude, it is found that the vibration friction coefficient decreases. The experimental results are in a good agreement with the theoretical calculations. The vibration friction model would be used to explain the driven mechanism of an ultrasonic motor in a further work.
STUDY ON THE DRIVING MODEL OF ULTRASONIC MOTOR

Li Huafeng,Zhao Chunsheng,Gu Chenglin

2006-01-01

Istanbul University - Journal of Electrical & Electronics Engineering

Abstract:The interface contact model between the stator and the rotor of traveling wave ultrasonic motor is presented, assuming that the rigid stator contacts the flexible rotor over an area, and the frictional material is regarded as distributed linear spring and without shearing deformation, from which the mechanical characteristic of the motor and the interface transmission efficiency are derived. And then the effects of the motor's parameters on its performance are investigated, which will be helpful to the design of the ultrasonic motor.
Dahl Friction Model for Driving Characteristics of V-Shape Linear Ultrasonic Motors

Bo Zhang,Xianghui Yuan,Yuansong Zeng,Lihui Lang,Hailong Liang,Yanhu Zhang

DOI: https://doi.org/10.3390/mi13091407

IF: 3.4

2022-01-01

Micromachines

Abstract:The contact process of stator and slider described by the Coulomb friction model is basically in a pure sliding friction state, and a mechanical model based on the Dahl friction theory was proposed to describe the contact process between stator and slider of V-shape linear ultrasonic motor. With consideration for the tangential compliance of stator and slider, the dynamic contact and friction processes of stator and slider were addressed in stages. The simulation results show that the ratio of the friction positive work decreases with the increase of the preload, and the vibration amplitude of the stator increases the proportion of positive work of the friction force. Improving the contact stiffness of the stator and slider is conducive to improving the output performance of the ultrasonic motor. The asymmetry of the left and right performance of the V-shaped vibrator will cause a difference in the left and right running speeds of the ultrasonic motor. The improved Dahl friction-driving model makes up for the discontinuity of tangential contact force calculated by the Coulomb friction model. This study demonstrates that the friction-driving model based on the Dahl theory is reliable and reasonable for linear ultrasonic motors according to the experimental results.
The Effects of Friction Coefficient on Driving Performance in Traveling Wave Ultrasonic Motor

Sun Fengyan,Wang Qingmei,Qu Jianjun

DOI: https://doi.org/10.4028/www.scientific.net/amr.204-210.1809

2011-01-01

Advanced Materials Research

Abstract:Traveling wave ultrasonic motor (TWUSM) is driven by friction force between stator and rotor, so friction coefficient is an important parameter of contact interface. In fact, there have mutual influence and restriction in various parameters of contact interface. For a comprehensive study on friction coefficient, the interaction between friction coefficient and other parameters should be considered. Base on a new contact model with visco-elastic stator contact layer of TWUSM，coupling effects of two parameters on motor output characteristics were simulated with MATLAB. According to the simulation results, a design principle of friction coefficient was present. A kind of Ekonol composite friction material (EK2) was developed under the guidance of this principle. Comparing with other common friction material of TWUSM, it was proved that motor with EK2 can get better running stability, higher output torque and longer lifetime. Therefore, EK2 is a good friction material which can satisfy the actual running needs of TWUSM.
A novel model of ultrasonic motors with effect of radial friction in contact mechanism

Chao Chen,Chunsheng Zhao

DOI: https://doi.org/10.1007/s10832-007-9195-2

2007-01-01

Journal of Electroceramics

Abstract:This paper is concerned with a development of the contact model of traveling wave type rotary piezoelectric ultrasonic motor, which takes into account a new three-dimensional operation mechanism between the stator and rotor. First the vibration characteristics and harmonic response of the stator are analyzed based on the mathematical model. With the derivation of the kinematical equations representing the motion of the stator surface points, the three-dimensional driving mechanism is investigated at the contact interface between the stator and rotor. We found that the distributed contact forces have not only the axial and circumferential components but also the radial component at the interface. The traditional contact model should be improved by the consideration of radial friction at the interface. So we defined driving angle α , which describes how the radial friction distributes at the interface. Furthermore it is shown that the radial friction can lead to considerable energy losses. A set simulation of motor performances based on the proposed contact mechanism is found in good agreement with experimental results. We also tried to explain how the applied normal preload force on rotor affect the natural frequency of stator by the contact interface, as is shown in our experiments.
Design principle and experiment of gradient friction material for ultrasonic motor

Yanli Wang,Jianjun Qu,Ningning Zhou,WeiLing Cui

DOI: https://doi.org/10.1109/SPAWDA.2010.5744299

2010-01-01

Abstract:As the key contact material part in ultrasonic motor (USM) system, friction materials play a very important role in USM by their influence on its efficiency, speed, torque, etc. Due to the special driving principle, contact and output properties of USM are influenced strongly by wear of friction material. Therefore, studies on special and high performance of friction material for USM are essential. Researches showed that the stability of contact and output of USM could be improved by using friction material with special gradient properties. In this paper, one kind of gradient coating friction material was made according to design principle of gradient friction material for USM. The gradient friction material is combined by three coating layers. Its elastic modulus declines from surface layer to bottom layer with decrease of whole thickness of gradient friction material. The contact state and drive properties of USM were measured between gradient friction material and one kind of homogeneous friction material. Compared to homogeneous friction material, USM with gradient friction material can obtain more stable of contact state and drive properties. The result could provide experimental guidance for design and choosing of friction material for USM.

An ultrasonic driving principle using friction reduction

Experimental Investigation on Friction Characteristics of Ultrasonic Motor

Study on Antifriction Effect of Ultrasonic Vibration in Ultrasonic Driving

A Method to Change Frictional Characteristics Based on Ultrasonic Micro Driving Technique

ANTIFRICTION MECHANISM OF ULTRASONIC VIBRATION BASED ON ULTRASONIC MICRO DRIVING

Experiment Study on Friction Reduction of Ultrasonic Vibration Based on Traveling Wave Ultrasonic Motor

Analysis on friction driving of linear ultrasonic motor with in-plane bending and longitudinal mode

Research Progresses in Friction Material for Ultrasonic Motor

An Equivalent Wear Method Of Friction Material For Ultrasonic Motor

Driving characteristics of ultrasonic motor with different application mode of friction material

Effect of Application Mode of Friction Material on Driving Characteristics of Ultrasonic Motor

Study of rotary ultrasonic vibration anti-friction experimental mechanism

Effects of Wear of Friction Material on Performance of Ultrasonic Motor

Gradient Design Model of Contact Interface for Ultrasonic Motor

Contact Process and Friction Analysis of Linear Ultrasonic Motor

The Measurement on Vibration Friction Coefficient of Ultrasonic Motor

STUDY ON THE DRIVING MODEL OF ULTRASONIC MOTOR

Dahl Friction Model for Driving Characteristics of V-Shape Linear Ultrasonic Motors

The Effects of Friction Coefficient on Driving Performance in Traveling Wave Ultrasonic Motor

A novel model of ultrasonic motors with effect of radial friction in contact mechanism

Design principle and experiment of gradient friction material for ultrasonic motor