Abstract:To assess the life of a new diesel aluminium alloy piston under thermal shock loads, thermo-mechanical fatigue (TMF) testing was conducted to characterise the TMF properties of the piston alloy, and an empirical model based on the constraint ratio concept was proposed to predict the TMF life of the piston. Considering that the empirical model required expensive experimental support, a platform with high-frequency induction heating was established to simulate the force on the piston under thermal shock loads to calculate the piston life using the thermal shock test. Additionally, a finite element method was developed to compute the distributions of temperature, strain, and stress during this process. The characteristics of crack initiation and propagation in TMF test rods and piston mock-ups were also investigated. The results showed that the TMF test rod suffered brittle fracture with brittle quasi-cleavage features. The microcracks mainly occurred in primary Si particles due to stress concentration around the primary Si particles induced by the difference between the thermal expansion coefficients of Si and Al. From a macro perspective, the piston initially cracked at the rim above the pinhole, where the stress is larger than that along other directions. From a micro perspective, the protrusions of various sizes on the piston rim were induced by the compression stresses at high temperature. The piston cracks usually initiate around primary Si particles, propagate along the edge of primary Si in a straight line, bifurcate and then stop at a certain depth. If the piston was only heated, cracks or plastic deformations were not produced. The piston life can be assessed using the proposed empirical model based on the constraint ratio concept or thermal shock testing based on the developed platform. The difference between the predicted and experimental life was not greater than 7%.

Double-stage Hardening Behavior and Fracture Characteristics of a Heavily Alloyed Al–Si Piston Alloy During Low-Cycle Fatigue Loading

Effect of Intermetallics on the Low Cyclic Fatigue Crack Growth Behavior of a Heavily Alloyed Al-Si Piston Alloy

Low cycle fatigue behavior of nickel-based superalloy GH4145/SQ at elevated temperature

Unique Cyclic Deformation Behavior of a Heavily Alloyed Al–Si Piston Alloy at Different Temperatures

Characterization of tensile fracture in heavily alloyed Al-Si piston alloy

Influence of Strain Amplitude on Low-Cycle Fatigue Behaviors of a Fourth-Generation Ni-Based Single-Crystal Superalloy at 980 °C

Cyclic Deformation Behavior of A Heat-Treated Die-Cast Al-Mg-Si-Based Aluminum Alloy

Low cycle fatigue response and fracture mechanism in a novel Al-3.5Si-0.5Mg-0.4Cu casting alloy

High-cycle fatigue failure analysis of cast Al-Si alloy engine cylinder head

Crack initiation and propagation characteristics of a dual‐phase Mg–Li alloy under high‐cycle and very‐high‐cycle fatigue regimes

Characterization of High-Cycle Bending Fatigue Behaviors for Piston Aluminum Matrix SiO2 Nano-composites in Comparison with Aluminum–Silicon Alloys

Enhanced low-cycle fatigue and crack propagation resistance of an Al-Cu-Mg-Si forging alloy by non-isothermal aging

Experimental and Computational Study on Thermo‐mechanical Fatigue Life of Aluminium Alloy Piston

High temperature low cycle fatigue and creep-fatigue behavior of a casting Al-9Si-CuMg alloy used for cylinder heads

Experiment and numerical simulation study of thermal fatigue of an aluminum alloy piston

Crack Configuration Feature and Fracture Surface Difference for High Pressure Die Casting Hypereutectic Al-Si Alloys in High Cycle Fatigue

Small fatigue crack growth in an extruded dual-phase Mg-Li alloy

Fretting Fatigue Behavior and Damage Mechanism of Cast Al-Si-Cu-T6 Alloy Under Two Surface Roughness conditions

Evaluation of Plastic Deformation and Prediction of Thermal Mechanical Fatigue Life of an Al–Si Alloy Piston for Diesel Engines

High Temperature Low-Cycle Fatigue, Deformation Microstructure and Final Fracture Behavior of a Nickel-Base Superalloy

Crack Initiation Mechanism in a High-Strength Ti-5Al-7.5V Alloy Subjected to High Cycle Fatigue Loading