Abstract:The Ti-4Al-2V (wt. %) titanium alloy has garnered widespread applications across diverse fields due to its exceptional strength-to-weight ratio, high toughness, specific strength, and corrosion resistance. The welding of Ti-4Al-2V titanium alloy components is often necessary in manufacturing processes, where the reliability of a welded joint critically influences the overall service life of these components. Consequently, a comprehensive understanding of the welded joint's microstructure and mechanical properties is imperative. In this study, Ti-4Al-2V titanium alloy was welded using multi-layer and multi-pass TIG welding techniques, and a detailed examination was conducted to analyze the microstructure and grain morphology of each microzone of the welded joint. The results revealed the presence of an initial α phase and a secondary lamellar α phase in the heat affected zone (HAZ). Meanwhile, the fusion zone (FZ) primarily comprised a coarse secondary α phase and a small amount of an acicular martensitic α' phase. Both the recrystallization zone and the superheated zone exhibited a distinct preferred orientation, with grains smaller than 10 μm accounting for 65.9% and 55.1%, respectively. To assess the mechanical properties of the various microzones and the typical microstructure within the welded joint, nanoindentation tests were performed. The results indicated that the recrystallization zone possessed a higher nanohardness (3.753 GPa) than the incomplete recrystallization zone (3.563 GPa) and the superheated zone (3.48 GPa). Among all the microzones, the FZ exhibited the lowest average nanohardness (3.058 GPa). Notably, the basket-weave microstructure demonstrated the highest average nanohardness, reaching 3.93 GPa. This was followed by the fine-grain microstructure, which possessed a slightly lower nanohardness. The Widmanstätten microstructure, on the other hand, exhibited the lowest nanohardness among the three microstructures within the HAZ. Therefore, the basket-weave microstructure stands out as the most desirable microstructure to achieve in the welded joint. In summary, this study provides a comprehensive characterization and analysis of the microstructure and properties of Ti-4Al-2V titanium alloy TIG welds, aiming to contribute to the optimization of the TIG welding process for Ti-4Al-2V titanium alloy.

Temperature dependence of tensile properties and fracture behavior of welded joints of titanium matrix composites in gas tungsten arc welding

Room temperature tensile fracture characteristics of in situ TiBw/Ti6Al4V composites with a quasi-continuous network architecture

Weld Zone Characteristic and Mechanical Performance of in Situ Titanium Matrix Composites Using Gas Tungsten Arc Welding (Gtaw)

Gas Tungsten Arc Welding of Network Structured Titanium Matrix Composite

Microstructures and Mechanical Properties in Laser Beam Welds of Titanium Matrix Composites

Investigation of the Effect of Argon Arc Welding Parameters on Properties of Thin Plate of in Situ Titanium Matrix Composites

Microstructure and High-Temperature Tensile Properties of Ti3Al Alloys Laser Welding Joint

Microstructure and Mechanical Properties of GTA Weldments of Titanium Matrix Composites Prepared with or Without Current Pulsing

The Microstructure and Mechanical Properties of Fluxless Gas Tungsten Arc Welding–brazing Joints Made Between Titanium and Aluminum Alloys

Microstructure Evolution and Mechanical Properties of Titanium Matrix Composites and Ni-based Superalloy Joints with Cu Interlayer

Effect of Heat Distribution on Microstructure and Mechanical Properties of Electron Beam Welded Dissimilar TiAl/TC4 Joint

Microstructure, texture, and compressive properties of TC11/TC17 linear friction welded joint at elevated temperatures

Microstructure evolution and strengthening mechanism of electron beam welded TiBw/Ti6Al4V composite joint

Microstructure Evolution and Tensile Properties of Laser-TIG Hybrid Welds of Ti 2 AlNb-Based Titanium Aluminide

Forming control and the relationship between microstructure and mechanical property in TIG-assisted friction stir welded joint of Ti-6Al-3Nb-2Zr-1Mo titanium alloy

An Investigation into the Microstructures and Mechanical Properties of a TIG Welding Joint in Ti-4Al-2V Titanium Alloy

Influence of High-Temperature Annealing on Microstructure and Properties of Welded Joints Using Narrow Gap Laser Welding of TC4 Titanium with Welding Wire

Temperature Dependence of Tensile Properties and Fracture Behavior of As Rolled Tib/Ti Composite Sheet

Study Of The Microstructure And Fracture Toughness Of Tc17 Titanium Alloy Linear Friction Welding Joint

Effects of heat input on microstructure evolution, mechanical and corrosion properties of TC4 alloy by keyhole TIG welding