Abstract:Abstract This paper presents the computational methodology and experimental investigations accomplished to enhance the efficiency of a turbine stage by applying non-axisymmetric profiling on the rotor hub wall. The experimental setup was a two-stage axial turbine, which was tested at “LISA” test facility at ETH Zurich. The first stage was considered to create the flow history for the second stage, which was the target of the optimization. The hub cavity of the second stage was designed with large dimensions as a requirement of a steam turbine. The goal was to optimize the interaction of the cavity leakage flow with the rotor passage flow to reduce the losses and increase efficiency. The computational optimization was completed using a genetic algorithm coupled with an artificial neural network on the second stage of the test turbine. Unsteady time-accurate simulations were performed using in-house developed “MULTI3” solver. Besides implementing all geometrical details (such as hub and tip cavities and fully 3D blade geometries) from the experimental setup into the computational model, it was learned that the unsteady upstream effect could not be neglected. A novel approach was introduced using unsteady inlet boundary conditions to consider the multistage effect while reducing the computational cost to half. The importance of this implementation was tested by performing a steady simulation on the optimized geometry. The predicted efficiency gain from steady simulations was 4.5 times smaller (and negligible) compared to the unsteady approach. Excluding the cavity geometry was also assessed in a different simulation setup showing 3.9% over-prediction in the absolute efficiency value. Comprehensive steady and unsteady measurements were performed utilizing pneumatic, fast response aerodynamic probe (FRAP), and fast response entropy probe (FENT) on the baseline and profiled test cases. The end wall profiling was found to be successful in weakening the strength of the hub passage vortex by a 19% reduction in the under-over turning. As a result, the blockage was reduced near the hub region leading to more uniform mass flow distribution along the span. The flow angle deviations at the higher span position were also corrected due to better control of the flow angles. Furthermore, the improvements were confirmed by reductions in entropy, secondary kinetic energy, and pressure unsteadiness. The accurate computational implementations led to an excellent agreement between the predicted and measured efficiency gain.

Aerodynamic Optimization of the Radial Inflow Turbine for A 100Kw-Class Micro Gas Turbine Based on Metamodel-Semi-Assisted Method

A throughflow-based optimization method for multi-stage axial compressor

Using an Optimisation Strategy to Design a Supercritical CO2 Radial Inflow Turbine Transonic Stator

Design and off-design performance improvement of a radial-inflow turbine for ORC applications using metamodels and genetic algorithm optimization

An Integrated Design and Optimization Approach for Radial Inflow Turbines-Part II: Multidisciplinary Optimization Design

Experimental And Numerical Investigation On Overall Performance Of A Radial Inflow Turbine For 100kw Microturbine

An Optimizing Method to Balance Aerodynamic Loading for Gas Turbine Engine Preliminary Design

Experimental Validation of an Integrated Optimization Design of a Radial Turbine for Micro Gas Turbines

Radial turbine optimization under unsteady flow using nature-inspired algorithms

Study on Aerodynamic Optimization Design Process of Multistage Axial Turbine

Aerodynamic Optimization of Multi-stage Axial Turbine Based on Pre-Screening Strategy and Directly Manipulated Free-Form Deformation

Optimization design of radial inflow turbine combined with mean-line model and CFD analysis for geothermal power generation

Multidisciplinary Design Optimization Based on Parameterized Free-Form Deformation for Single Turbine

Optimization Of High Speed Centrifugal Compressor For A Micro Gas Turbine Based On Cfd And Fem Analysis

Aerodynamic Optimization Of A Sco2 Radial-Inflow Turbine Based On An Improved Simulated Annealing Algorithm

Strength Design And Numerical Analysis Of Radial Inflow Turbine Impeller For A 100kw Microturbine

Unsteady Steam Turbine Optimization Using High-Fidelity Computational Fluid Dynamics

Aerodynamic Design by Jointly Applying S2 Flow Surface Calculation and Modern Optimization Methods on Multistage Axial Turbine

Numerical Investigation and Performance Enhancement of an Ammonia-Water Radial-Outflow Turbine Through the Flow-Oriented Optimization

Identification of nonparametric thermodynamic model and optimization of ocean thermal energy conversion radial inflow turbine

Aerothermodynamic Design and Numerical Simulation of Radial Inflow Turbine Impeller for A 100kw Microturbine