Abstract:The 2195 Al-Cu-Li alloy is widely utilized for the fabrication of key aerospace vehicle components; hence, an in-depth understanding of its hot deformation behavior is essential for consistently achieving high-performance products. In this study, isothermal compression tests were performed on 2195 Al-Cu-Li alloy ingots in the temperature and strain rate ranges of 250–500 °C and 10 −3 -1 s −1 , respectively. A processing map was established to predict the workability under different conditions. The corresponding microstructures were examined to reveal their hot deformation mechanism. Results demonstrated that the processing map was divided into four distinct domains. The unstable zone was located in the 250–375 °C/10 −1.5 -1 s −1 and 250–275 °C/10 −2.5 –10 −1.5 s −1 , temperature/strain rate regimes, in which deformation bands and flow localization were observed. The deformation bands blocked dislocations and compromised the dynamic recrystallization (DRX) behavior, hence damaging the microstructure. Further, large coarse T 1 phases precipitated in the 325–410 °C/10 −2.5 –10 −3 s −1 regime, which led to the formation of heterogeneities in the microstructure, corresponding to a minimum workability in the processing map. The optimal hot-working domain for the 2195 alloy was determined to be 460–500 °C/10 −3 –10 −2 s −1 , and the dominating hot deformation mechanisms were DRX and dynamic recovery (DRV). Specifically, continuous and discontinuous DRX behaviors dominated in the 300–400 °C/10 −3 s −1 and 450–500 °C/10 −3 s −1 regimes, respectively. DRX gradually weakened as the strain rate increased at 500 °C. Further, the weakening of DRX was only minimally affected by temperature at 400–500 °C during high-speed deformation (1 s −1 ). The results reported herein can provide valuable insights into the hot working of Al-Cu–Li alloys.

Hot deformation and processing maps of Fe-B alloy

Hot deformation behavior of BFe30-1-1 alloy and its hot processing map

Hot Deformation Constitutive Model and Processing Maps of Homogenized Al–5Mg–3Zn–1Cu Alloy

Hot Deformation and Processing Maps of 7005 Aluminum Alloy

Hot Deformation Behavior and Processing Maps of 2099 Al-Li Alloy

Characterization of Hot Deformation Behavior and Processing Maps of Homogenized Al-Mg-Si-Sc-Zr Alloys

Constitutive equation and hot processing maps of Al–5Ti–1B master alloy

Characterization on Hot Deformation Behavior of Ti-22Al-25Nb Alloy Using a Combination of 3D Processing Maps and Finite Element Simulation Method

The hot deformation behavior and processing map of Ti–47.5Al–Cr–V alloy

Hot deformation behavior and microstructural evolution of the Al-Cu-Li alloy: A study with processing map

Hot Deformation Characteristics and Processing Parameter Optimization of Al–6.32Zn–2.10Mg Alloy Using Constitutive Equation and Processing Map

Hot deformation behavior and microstructure characterization of AlCrFe2Ni2(MoNb)0.2 high entropy alloy

The Hot Deformation Behavior and Processing Map of Powder Metallurgy Nial-Based Alloy

Hot Workability and Microstructure Evolution of Homogenized 2050 Al-Cu-Li Alloy during Hot Deformation

Hot Deformation Behavior and Processing Map of a Γ′-Hardened Nickel-Based Superalloy

Hot Deformation Behavior of Homogenized Al-7.8Zn-1.65Mg-2.0Cu (wt.%) Alloy

Hot Deformation Behavior and Processing Map of a Nickel-Base Superalloy GH4169

Hot Deformation Behavior and Processing Maps of Ti-1300 Alloy

Hot Deformation Behaviours and Spheroidization Mechanisms of Ti-5322 Alloy During Hot Compression

Exploring hot deformation behavior of equimolar CoCrFeNi high-entropy alloy through constitutive equations and microstructure characterization

Revealing Hot Deformation Behavior and Optimizing Process Parameters of As-Cast Ti–5Al–5Mo–5V–1Cr–1Fe Alloy