Abstract:High undercooling rapid solidification process has a significant impact on the solidified microstructure and mechanical properties of materials. In this study, particles with a diameter range between 100 and 1100 μm of ternary Zr 50 Cu 40 Al 10 and Zr 49 Cu 46 Al 5 alloys were prepared by a drop tube. The evolution process of particle-solidified microstructure with decreasing particle diameter was analyzed using XRD, SEM, and TEM. For Zr 50 Cu 40 Al 10 alloy, the solidified microstructure in the particle diameter ranges of 200–1100 μm is composed of an amorphous phase and a primary B2-ZrCu high-temperature metastable phase. As the particle diameter reduces, the retained crystalline phase in the solidified microstructure decreases progressively, and the dendrite grain length gradually becomes finer. When the particle diameter is reduced to below 200 μm, the crystalline phase has completely disappeared, and the solidified microstructure evolves into a completely amorphous structure. For Zr 49 Cu 46 Al 5 alloy, in the particle diameter range of 400–1100 μm, the solidified microstructure consists of primary B19'-ZrCu phase, a small amount of Cu 10 Zr 7 phase and Zr 14 Cu 51 phase. As the particle diameter reduces, a grain refinement phenomenon also occurs in the solidified microstructure and the dendritic morphology changes from equiaxed grain to rod-shaped dendrite. The amorphous phase appears when the particle diameter is lowered to 470 μm and solidified microstructure evolves into a completely amorphous structure as the particle diameter is reduced to 146 μm. The nanoindentation results show that the micromechanical properties of amorphous composite microstructures are superior to the single component composition of crystalline or amorphous phase for Zr 50 Cu 40 Al 10 and Zr 49 Cu 46 Al 5 alloys. The reinforcement effect on the amorphous phase is related to the content of the second crystalline phase. Moreover, under similar particle diameters, the mechanical properties of Zr 50 Cu 40 Al 10 particles are always better than those of Zr 49 Cu 46 Al 5 particles.

Formation of Fine Multicomponent Precipitates and Enhanced Precipitation-Hardening in an Al–Cr–Pr–Zr Alloy

Effect of Cr on solidification structure and microhardness of Al-Ni alloy

New insight into precipitation of Al3Zr and correlative effect on recrystallization behavior in a rapidly-solidified Al-Zn-Mg-Cu-Zr alloy

Characterization of Al3Zr precipitation via double-step homogenization and recrystallization behavior after subsequent deformation in 2195 Al-Li alloy

Effect of Trace Zr on Microstructure and Hardness of Al-Zn-Mg-Cu Alloy Prepared under Supergravity

Effect of Al–Er–Zr Master Alloy on Grain Refinement After Heat Treatment

Influence of Zr Microalloying on the Microstructure and Room-/High-Temperature Mechanical Properties of an Al–Cu–Mn–Fe Alloy

Effect of Zr Microalloying on the Microstructures and Strengthening Mechanism of As-Cast Al-Fe-Zr Alloys

Effect of Zr addition on the microstructure evolution and mechanical properties of extruded Al-Cu-Li-Mn alloys

Crystalline and amorphous microstructure evolution of Zr-Cu-Al ternary alloys solidified in drop tube

Effect of Chromium on Microstructure and Mechanical Properties of Al–Cu–Er–Zr Alloy

Effects of addition of Er and Zr on microstructure and mechanical properties of Al–Cu–Mn–Si–Mg alloy

Dynamic recrystallization and precipitation behavior of a novel Sc, Zr alloyed Al-Zn-Mg-Cu alloy during hot deformation

The effect of zirconium on the microstructure and mechanical properties of a super-high-strength Al-Zn-Mg-Cu alloy

EFFECT OF Zr ADDITION ON MICROSTRUCTURE AND MECHANICAL PROPERTIES OF NiAl/Cr(Mo)BASE EUTECTIC ALLOY

Influence of Zr content on microstructure and mechanical properties of As-cast Al-Zn-Mg-Cu alloy

Precipitation Thermodynamics in an Al–Zn–Mg Alloy with Different Grain Sizes

Precipitation in lean Mg-Zn-Ca alloys

Effects of Zr on high temperature deformation and dynamic precipitation of laves phase in Fe–13Cr–5Al–2Mo–0.5Nb–0.4Ta alloy

Microstructural Evolution of a High-Strength Zr-Ti-Modified 2139 Aluminum Alloy for Laser Powder Bed Fusion

Effects of Zr and Sr on microstructure and mechanical properties of cast Al–Si–Cu–Ni–Mg alloy