Abstract:In order to study the effect of the rolling process and aging on the microstructure evolution and mechanical and tribological properties of the material, room-temperature rolling (RTR), cryogenic rolling (CR), and deep cryogenic treatment after rolling (RTR + DCT) experiments were carried out on a Cu-1.0Cr-0.1Zr alloy by a large plastic deformation process. Alloy plates were aged at 550 °C for 60 min. Different rolling processes and aging treatments have different effects on the microstructure and properties of alloy plates. The alloy plate is rolled and deformed, and the grains change from equiaxed to layered. Compared with RTR and RTR + DCT treatment, CR can promote the precipitation of the Cr phase and the degree of grain fragmentation is greater. After aging treatment, the Cu-Zr mesophase compounds in the microstructure increased, the alloys treated with CR and RTR + DCT appeared to be partially recrystallized, and the number of twins in the CR alloy plate was significantly more than that of RTR + DCT. The ultimate tensile strength of the alloy plate reached 553 MPa and the hardness reached 170 HV after cryogenic rolling with 90% deformation, which indicates that CR treatment can further improve the physical properties of the alloy plate. After aging at 550 °C for 60 min, the RTR 90% + DCT alloy plate has a tensile strength of 498 MPa and an elongation of 47.9%, which is three times that of the as-rolled alloy plate. From the research on the tribological properties of alloy plates, we learned that the main wear mechanisms in the wear forms of CR and RTR + DCT alloy plates are adhesive wear and abrasive wear. Adhesive wear is dominant in the early stage, while abrasive wear is the dominant mechanism in the later stage of wear. The friction coefficient of the CR 90% alloy plate in the TD direction is close to 0.55, and the wear rate is 2.9 × 10-4 mm3/Nm, indicating that the CR treatment further improves the wear resistance of the alloy plates.

Microstructure and Properties of Rapidly Solidified Cu-0.81cr-0.12zr Alloy

Effect of Heat Treatment Process on Properties of ITER-grade CuCrZr Alloy

Microstructure and Properties of Rare Earth-Containing Cu–Cr–Zr Alloy

A High Strength and High Conductivity Cu0.4Cr0.3Zr Alloy Prepared by Cryo-ECAP and Heat Treatment

The influence of Zr concentration on the microstructure and properties of Cu-0.6Cr-xZr alloy: High-throughput preparation and characterization study

Microstructure and Properties of Rapid Solidified Cu_(71)Cr_(29) Alloy

Effect of elevated-temperature annealing on microstructureand properties of Cu−0.15Zr alloy

Effect of ECAP by Route BC and Aging Heat Treatment on the Structure and Properties of Cu0.4Cr0.3Zr Alloy

Rapid Solidification of Cu60Co30Cr10 Alloy under Different Conditions

Microstructure and Properties of Cu – Cr – Zr Alloys After Plastic Deformation and Aging

Microstructure and properties of Cu-Cr-Zr (Mg) alloys subjected to cryorolling and aging treatment

Thermal Stability of Heavily Drawn Cu–0.4 Wt.%cr–0.12 Wt.%zr–0.02 Wt.%si–0.05 Wt.%mg

Effect of heat treatments on microstructure, mechanical and electrical properties of Cu–Cr–Zr alloy manufactured by laser powder bed fusion

Microstructural Evolution and Mechanical Properties of Cast Al-3li-1.5cu-0.2zr Alloy During Heat Treatment

Micro/nanostructure high strength and high conductivity CuCrZr alloy prepared through equal channel angular pressing and aging treatment

Effect of Rapid Solidification Process on the Alloy Structure and Electrode Performance of Zr(Ni0.55V0.1Mn0.3Cr0.55)2.1

Effects of Zr addition on the liquid phase separation and the microstructures of Cu-Cr ribbons with 18-22 at.% Cr

Microstructure of Rapidly Solidified Cu83Fe17 Alloys

Aging Property of Cu-Ag-Zr Alloy

Effect of Rolling Process and Aging on the Microstructure and Properties of Cu-1.0Cr-0.1Zr Alloy

Interaction of precipitation and recrystallization in rapidly solidified Cu-Cr-Zr-Mg alloy