Abstract:The presence of excessive residual recrystallization structure in the aero-structural part of the Al-Zn-Mg-Cu alloy negatively affects its strength and stress corrosion resistance . To achieve higher service performance, it is significant to reveal the recrystallization behavior of the Al-Zn-Mg-Cu alloy during hot working and subsequent heat treatment. In this work, the isothermal compression tests of an Al-Zn-Mg-Cu alloy were performed at the temperature range 300–450 °C and strain rate range 0.01–10 s −1 . The subsequent heat treatment of the deformed specimens was conducted. The microstructure was characterized by EBSD and XRD techniques. The natural logarithm of Zener-Hollomon parameter (lnZ) was introduced, which increases with the increasing strain rate and decreasing temperature. During hot deformation, CDRX was identified to be the predominant DRX mechanism at high lnZ values, the corresponding recrystallization volume fraction was approximately 15 %. However, at low lnZ values, DDRX becomes the dominant mechanism, the corresponding recrystallization volume fraction was only around 5 %. Moreover, a kinetics analysis was conducted using a low proportion DRX model coupled with lnZ. By comparing the results obtained from finite element simulations with experimental findings, this model was proved to accurately predict the volume fraction of DRX during hot deformation. During the heat treatment process, due to the substantial storage of deformation energy, a significant portion (up to 84.5 %) of SRX was observed under high lnZ conditions. As the lnZ value decreases, the SRX weakens. This weakening is significant enough that under high temperature and low strain rate, the occurrence of SRX becomes extremely unlikely, which can be attributed to the low storage of deformation energy.

Microstructure and Properties of Cu – Cr – Zr Alloys After Plastic Deformation and Aging

Micro/nanostructure high strength and high conductivity CuCrZr alloy prepared through equal channel angular pressing and aging treatment

Effect of ECAP by Route BC and Aging Heat Treatment on the Structure and Properties of Cu0.4Cr0.3Zr Alloy

Microstructure and properties of Cu-Cr-Zr (Mg) alloys subjected to cryorolling and aging treatment

Microstructure and Electrical Properties Evolution of Cu-3 ％ Cr During Aging

Study of Deformation and Aging Behaviors of a Hot Rolled–quenched Cu–Cr–Zr–Mg–Si Alloy During Thermomechanical Treatments

Microstructure and Properties of Rare Earth-Containing Cu–Cr–Zr Alloy

Dynamic Properties of Low-Alloyed Copper Alloys with Submicrocrystalline Structure Obtained by High Strain Rate Deformation

Aging Property of Cu-Ag-Zr Alloy

Microstructure and Properties of Rapidly Solidified Cu-0.81cr-0.12zr Alloy

A High Strength and High Conductivity Cu0.4Cr0.3Zr Alloy Prepared by Cryo-ECAP and Heat Treatment

Study on the inhomogeneity of Al–Zn–Cu–Mg aluminum alloy plates with different thickness

Effect of heat treatments on microstructure, mechanical and electrical properties of Cu–Cr–Zr alloy manufactured by laser powder bed fusion

Effect of minor Sc and Zr on recrystallization behavior and mechanical properties of novel Al–Zn–Mg–Cu alloys

Microstructures and Mechanical Properties of Al-Zn-Mg-Cu Alloys under Multi-Directional Severe Strain and Aging

Microstructural evolution and mechanical property of Cu‐Cr‐Zr‐ZrB2 composites subjected to cryorolling and aging treatment

Evolution of the microstructure and properties of a Cu–Cr-(Mg) Alloy upon thermomechanical treatment

Microstructural Evolution and Mechanical Properties of Cast Al-2Li-2Cu-0.5Mg-0.2Zr Alloy During Heat Treatment

Effect of elevated-temperature annealing on microstructureand properties of Cu−0.15Zr alloy

Recrystallization behavior of an Al-Zn-Mg-Cu alloy during hot deformation and subsequent heat treatment

Effect of deformation and aging treatment on the microstructure and properties of Cu-0.45Cr-0.14Ti (wt.%) alloy