Abstract:High Nb containing TiAl alloy powders with or without mechanical milling were consolidated by spark plasma sintering (SPS) technique. The effects of SPS temperature and mechanical-milling treatment on phase constitution and microstructure were studied, and the mechanical properties at room temperature were tested. The phases in the as-atomized powder are composed of major α2 phases, a few γ phases and a trace of β phases. After milling, the diffraction peaks for α2 phase are obviously broadened, and the intensities of diffraction peaks for both γ phase and β phase are decreased. Similar phase constitution including a large quantity of γ phases and a few α2 phases are exhibited in the alloys sintered by either as-atomized powder or as-milled powder. At a sintering temperature of 1200°C, the microstructure of the alloy sintered by using as-atomized powder consists of inhomogeneous γ and α2 phases as well as a few α2/γ lamellar colonies. By contrast, the densities increase and the microstructures are apparently refined for the alloys sintered by using as-milled powder. Fully dense alloys with uniformly distributed γ and α2 grains can be obtained at extending milling time or increasing rotating speed. The nucleation of γ phase during SPS of the powders is dependent on recrystallization. The heterogeneity of deformation should be responsible for the formation of heterogeneous γ grains in the alloys sintered by using as-atomized powder. The heterogeneous grain size for the alloys sintered by using as-milled powders is mainly derived from the inhomogeneous nucleation of γ phase and the uneven distribution of α2 grains. Good mechanical property accompanied by a fine grain size and a dense microstructure can be achieved by optimizing the process parameters.

Effects of Ball Milling Time and Sintering Temperature on Microstructure and Room-Temperature Mechanical Properties of Nb-16Si-22Ti-2Al-2Hf-2Cr Alloy Synthesized by Powder Metallurgy

Investigation of a Hot-Pressed Nb–Ti–Al Alloy: Mechanical Alloying, Microstructure and Mechanical Property

Microstructural Evolution and Mechanical Properties of a Multicomponent Nb-16Si-22Ti-2Al-2Hf-2Cr Alloy Prepared by Reactive Hot Press Sintering

Morphology and Phase Constituents of Mechanically Alloyed Nb-Ti-Si Based Ultrahigh Temperature Alloy Powders

Microstructural Evolution, Thermal Stability and Microhardness of the Nb–Ti–Si-Based Alloy During Mechanical Alloying

Effect of Mechanical Alloying on Microstructure and Mechanical Properties of Hot-Pressed Nb–16Si Alloys

Mechanical Alloying Behavior of Nb–Ti–Si-based Alloy Made from Elemental Powders by Ball Milling Process

Microstructure and room temperature mechanical properties of hot-pressed Nb–Si–Ti–Fe alloys

Microstructure and Mechanical Properties of the Powder Metallurgy Nb-16Si-24Ti-2Al-2Cr Alloy

Alloying effects on the microstructure and properties of Nb–Si based ultrahigh temperature alloys

EFFECTS OF HIGH-ENERGY BALL MILLING ON THE STRUCTURE AND PROPERTY OF A MULTIPHASE Al3Ti-BASED INTERMETALLIC ALLOY

Effect of Ball Milling Time on Microstructure and Properties of Laves Phase NbCr2 Alloys Synthesized by Hot Pressing

Effect of ball milling time on nanocrystalline powders and bulk ultrafine-grained Mg-3Al-Zn alloy

Microstructures and Mechanical Properties of Ti-45Al-10Nb Alloy Produced by Ball Milling and Hot Press Consolidation

Investigation on microstructure and properties of Ti-45Al-5.5(Cr, Nb, B, Ta) alloy prepared by double mechanical milling (DMM) and spark plasma

Microstructure Characterization and Mechanical Properties of TiAl-based Alloys Prepared by Mechanical Milling and Spark Plasma Sintering

Mechanical alloying, microstructure and properties of Nb–16Si alloy

Influence of Mechanical Alloying and Sintering Temperature on the Microstructure and Mechanical Properties of a Ti-22Al-25Nb Alloy

Effects of Ball Milling Time on the Microstructure and Mechanical Property of Cu90Al10 Alloy

Microstructure and Mechanical Properties of Ti–22Al–25Nb Alloy Fabricated by Elemental Powder Metallurgy

Effect of Ball Milling Time on Microstructures and Mechanical Properties of Mechanically-Alloyed Iron-Based Materials