Abstract:The gel layer is a superior strategy to optimize the interface compatibility between the conventional polyolefin separator and the electrode. In our study, the surface of the polyethylene (PE) separator is coated with polyvinylidene fluoride (PVDF) gel using a simple phase transformation method, resulting in the preparation of a composite separator consisting of PE and PVDF. The introduction of the gel layer enhances the interface compatibility between the conventional polyolefin separator and the electrode. The prepared PE/PVDF composite separator exhibits an increased lithium‐ion transference number (0.41) and enhanced ionic conductivity (1.77 mS cm−1). The cell has excellent cycle performance. After the introduction of the gel layer, the discharge capacity of the battery after 250 cycles measures ~1.28 mAh, with a mere 27% decay in capacity. At the same time, it also improves the rate performance of the cell. After 250 h of cycling, the polarization voltage is only about 0.14 V. The interface issue concerning lithium dendrite formation between the separator and electrode remains a significant impediment to the further advancement of lithium‐ion batteries (LIB). Due to the inadequate interface compatibility between the conventional polyolefin separator and the electrode, there is a propensity for lithium dendrite growth. In this work, the surface of the polyethylene (PE) separator is coated with polyvinylidene fluoride (PVDF) gel using a simple phase transformation method, resulting in the preparation of a composite separator consisting of PE and PVDF. The results demonstrate an enhanced interface compatibility following the introduction of the gel layer, with a polarization voltage as low as 0.14 V observed after 250 h of cycling. Additionally, the ionic conductivity of the PE/PVDF composite separator (1.77 mS cm−1) is enhanced, attributed to the incorporation of F functional group in PVDF gel, which could facilitate the formation of a rapid ion transport pathway through the interaction between F functional group and Li+. After the introduction of the gel layer, the discharge capacity of the battery after 250 cycles measures ~1.28 mAh, with a mere 27% decay in capacity. This study presents a novel concept for the design of composite separator in LIB.

Composite of a nonwoven fabric with poly(vinylidene fluoride) as a gel membrane of high safety for lithium ion battery

A Trilayer Poly(Vinylidene Fluoride)/Polyborate/Poly(Vinylidene Fluoride) Gel Polymer Electrolyte with Good Performance for Lithium Ion Batteries

Novel Configuration of Polyimide Matrix-Enhanced Cross-Linked Gel Separator for High Performance Lithium Ion Batteries

Preparation and Properties of Gel Membrane Containing Porous PVDF-HFP Matrix and Cross-Linked PEG for Lithium Ion Conduction

A Sandwich PVDF/HEC/PVDF Gel Polymer Electrolyte for Lithium Ion Battery

Honeycomb-like porous gel polymer electrolyte membrane for lithium ion batteries with enhanced safety

A superior thermostable and nonflammable composite membrane towards high power battery separator

Fabrication electro-spun Poly(vinyl alcohol)-Melamine nonwoven membrane composite separator for high-power lithium-ion batteries

A Magnesium Carbonate Hydroxide Nanofiber/Poly(Vinylidene Fluoride) Composite Membrane for High-Rate and High-Safety Lithium-Ion Batteries

Electrospun Fluorinated Polyimide/Polyvinylidene Fluoride Composite Membranes with High Thermal Stability for Lithium Ion Battery Separator

Cellulose/Polysulfonamide Composite Membrane as a High Performance Lithium-Ion Battery Separator

Tri-layer Nonwoven Membrane with Shutdown Property and High Robustness As a High-Safety Lithium Ion Battery Separator

Morphology optimizing of polyvinylidene fluoride ( PVDF ) nanofiber separator for safe lithium‐ion battery

Electrospun of polyvinyl alcohol composite hydrogel nanofibers prepared by in-situ polymerization: A novel approach to fabricate hydrogel nanofiber membrane for lithium-ion batteries

A gel polymer electrolyte obtained from cellulose acetate/polyvinylidene fluoride composite electrospun membrane for safe lithium metal batteries with high-rate capability

Ether Modified Poly(ether Ether Ketone) Nonwoven Membrane with Excellent Wettability and Stability As a Lithium Ion Battery Separator

Deformable and Flexible Electrospun Nanofiber-Supported Cross-Linked Gel Polymer Electrolyte Membranes for High Safety Lithium-Ion Batteries

Composite Polymer Electrolyte Membranes Supported by Non-Woven Fabrics for Lithium-Ion Polymer Batteries

Nylon-Based Composite Gel Membrane Fabricated via Sequential Layer-By-Layer Electrospinning for Rechargeable Lithium Batteries with High Performance

Preparation and Properties of Poly (vinylidene Fluoride)/poly(dimethylsiloxane) Graft (poly(propylene Oxide)-Block-poly(ethylene Oxide)) Blend Porous Separators and Corresponding Electrolytes

Polyvinylidene fluoride gel‐polyethylene composite separator optimizing the interface compatibility between the separator and the electrode