Abstract:Legislations concerning emissions from heavy-duty diesel engines are becoming increasingly stringent. This requires conventional diesel combustion to be compliant using costly and sophisticated aftertreatment systems. Preferably, diesel–methanol dual-fuel is one of the suitable alternative combustion modes as it can potentially reduce the formation of nitrogen oxide and soot emissions which characterised the diesel mixing-controlled combustion. This is primarily due to the high latent heat of vaporisation and oxygen content of the methanol fuel. At high engine loads, however, the potential of diesel–methanol dual-fuel operation is constrained by the excessive combustion pressure rise rate and peak in-cylinder pressure, which limits both the engine efficiency and the percentage of methanol that can be used. For the first time, experimental studies were conducted to explore advanced combustion control strategies such as Miller cycle, exhaust gas recirculation, and intake air cooling for improving upon high load diesel–methanol dual-fuel combustion. Experiments were carried out at 1200 r/min and 18 bar indicated mean effective pressure on a single-cylinder heavy-duty diesel engine, which equipped with a high pressure common rail diesel injection, a methanol port fuel injection, and a variable valve actuation system on the intake camshaft. Results showed that the methanol energy fraction of a conventional diesel–methanol dual-fuel operation with a baseline intake valve closing timing was limited to 28%. This was due to the high combustion temperature at a high load which advanced the ignition timing of the premixed charge, resulting in high levels of pressure rise rate. The application of lower effective compression ratio and intake air temperature ( T int ) effectively decreased the compression temperature, which successfully delayed the ignition timing of the premixed charge. This allowed for a more advanced diesel injection timing to achieve improvement in the thermal efficiency and potentially enabled a higher methanol substitution ratio. Although the introduction of exhaust gas recirculation demonstrated very slight impact on the ignition timing of the premixed charge, a higher net indicated efficiency was observed due to a relatively lower local combustion temperature which reduced heat transfer loss. Moreover, the optimised diesel–methanol dual-fuel operation allowed a higher methanol energy fraction of 40% to be used at an effective compression ratio of 14.3 and T int of 305 K and achieved the highest net indicated efficiency of 47.4%, improving by 3.7% and 2.6%, respectively, when compared to the optimised conventional diesel combustion (45.7%) and conventional diesel–methanol dual-fuel (46.2%). This improvement was accompanied with a reduction of 37% in nitrogen oxide emissions and little impact on soot emissions in comparison with the conventional diesel combustion.

Research on Using Egr and Ignition Timing to Control Load of A Spark-Ignition Engine Fueled with Methanol

Engine Performance and Emissions of A Compression Ignition Engine Operating on the Diesel-Methanol Blends

Combustion and Emission Characteristics of a DI Diesel Engine Fueled by Diesel-Methanol Blends

Improvement of the light-load combustion control strategy for a heavy-duty diesel engine fueled with diesel/methonal by RSM-NSGA III

Parametric study on effects of excess air/fuel ratio, spark timing, and methanol injection timing on combustion characteristics and performance of natural gas/methanol dual-fuel engine at low loads

Effects of injection and spark timings on combustion, performance and emissions (regulated and unregulated) characteristics in a direct injection methanol engine

The influence of exhaust gas recirculation coupling with fuel injection pressure on the combustion and emission characteristics of engine fueled with methanol-gasoline blends

Experimental Investigation on the Effects of Direct Injection Timing on the Combustion, Performance and Emission Characteristics of Methanol/Gasoline Dual-Fuel Spark Turbocharged Ignition (DFSI) Engine with Different Injection Pressures under High Load

Influence of ignition timing on performance and emission characteristics of an SI engine fueled with equi-volume blend of methanol and gasoline

Effects of Injection Parameters and EHN Mixing on the Combustion Characteristics of Fueling Pure Methanol in a Compression Ignition Engine

A comparative study on operating range and combustion characteristics of methanol/diesel dual direct injection engine with different methanol injection timings

Study on Combustion Characteristics of a DI Diesel Engine Operating on Diesel/Methanol Blends

Effects of different valve lift adjustment strategies on stoichiometric combustion and lean burn of engine fueled with methanol/gasoline blending

Improving the lean burn performance of a high compression ratio methanol engine by multiple-injection

Experimental study on effects of pilot injection strategy on combustion and emission characteristics of diesel/methanol dual-fuel engine under low load

Experimental study of knock combustion and direct injection on knock suppression in a high compression ratio methanol engine

Exploring the high load potential of diesel–methanol dual-fuel operation with Miller cycle, exhaust gas recirculation, and intake air cooling on a heavy-duty diesel engine

Numerical Investigation on the Influence of Injection Location and Injection Strategy on a High-Pressure Direct Injection Diesel/Methanol Dual-Fuel Engine

Effects of fuel injection timings and methanol split ratio in M/D/M strategy on a diesel/methanol dual-fuel direct injection engine

Study on the Influence of Different Internal Exhaust Gas Recirculation Formation Modes on the Combustion Performance of Gasoline, Methanol, and Ethanol SI Engine

Experimental Investigation on the Emissions of a Port Fuel Injection Spark Ignition Engine Fueled with Methanol–Gasoline Blends