Abstract:Here, an anionic surfactant [AOT]- (bis-(2-ethylhexyl) sulfosuccinate)-stabilized H2O/[Omim][PF6] (1-octyl-3-methylimidazolium hexafluorophosphate) microemulsion has been tested for the first time as a medium for the electropolymerization of 3,4-ethylenedioxythiophene (EDOT). To formulate AOT-stabilized [Omim][PF6]-based microemulsions of different water contents, the phase triangle was determined at 35 °C. Measurements of the conductivities of the microemulsions, their solubilization capacities toward EDOT and their catalytic effects on EDOT electrooxidation show that the present [AOT]--stabilized ionic liquid microemulsion is a good medium for EDOT electropolymerization. Studies on the process of the electropolymerization of EDOT in this [Omim][PF6]-based microemulsion indicate that the water content (i.e., microstructure) of the microemulsion medium is an important factor affecting the onset potential and the deposition rate of the PEDOT. The morphology and the doping level of the as-prepared PEDOT are also found to be correlated with the water content of the ionic liquid microemulsion. The microemulsion with higher water content results in a PEDOT with better electroactivity and higher doping levels. FTIR spectra and XPS analysis show that the PEDOT electrosynthesized in the microemulsion is co-doped by both [AOT]- and [PF6]-. Compared with the neat [Omim][PF6], the use of the ionic liquid microemulsions can reduce not only the consumption of the expensive ionic liquid, but also the onset potential for the electrooxidation of EDOT. Moreover, by tuning the water content of the medium, the electropolymerization of PEDOT and its electrochemical properties could be regulated accordingly. Under the identical deposited charge, the PEDOT originated from the high water content microemulsion (50% H2O μE) has a higher specific capacitance (124 F g-1) than that from neat [Omim][PF6] (117 F g-1). It follows that the present ionic liquid microemulsion is a good medium for EDOT electropolymerization. The present study opens up a new route for the green and low-cost electrochemical preparation of high-performance PEDOT.

Electrodeposition of Poly(3,4-Ethylenedioxythiophene) on A Stainless Steel Wire for Solid Phase Microextraction and Gc Determination of Some Esters with High Boiling Points

Solid-phase microextraction of phthalate esters from aqueous media by electrophoretically deposited TiO₂ nanoparticles on a stainless steel fiber

Preparation of Nanoporous Array Anodic Titanium Wire Supported Solid-Phase Microextraction Fiber Coated with A Copolymerized Polymerizable Ionic Liquid Monomer Pair

Electrochemical In Situ Fabrication of Titanium Dioxide Nanotubes on a Titanium Wire as a Fiber Coating for Solid-Phase Microextraction of Polycyclic Aromatic Hydrocarbons

Polymeric Ionic Liquid Modified Stainless Steel Wire As A Novel Fiber for Solid-Phase Microextraction

A Polythiophene/uio-66 Composite Coating for Extraction of Volatile Organic Compounds Migrated from Ion-Exchange Resins Prior to Their Determination by Gas Chromatography.

Graphene Oxide Decorated with Silver Nanoparticles As a Coating on a Stainless-Steel Fiber for Solid-Phase Microextraction.

Cnt-Tio2 Coating Bonded Onto Stainless Steel Wire As A Novel Solid-Phase Microextraction Fiber

Adsorption mechanism of polycyclic aromatic hydrocarbons on polythiophene-graphene covalent complex and its analytical application in food contact materials

Electropolymerization of EDOT in an anionic surfactant-stabilized hydrophobic ionic liquid-based microemulsion.

Polythiophene As a Novel Fiber Coating for Solid-Phase Microextraction

Hydrofluoric acid etched stainless steel wire for solid-phase microextraction.

Trifluoroacetic acid modified MOF-808 composite coating for solid-phase microextraction of six phenols followed by gas chromatography analysis

Preparation of sulfonated graphene/polypyrrole solid-phase microextraction coating by in situ electrochemical polymerization for analysis of trace terpenes

Microextraction of Polycyclic Aromatic Hydrocarbons by Using a Stainless Steel Fiber Coated with Nanoparticles Made from a Porous Aromatic Framework.

Determination of Volatile Water Pollutants Using Cross-Linked Polymeric Ionic Liquid as Solid Phase Micro-Extraction Coatings

Novel unbreakable solid-phase microextraction fibers on stainless steel wire and application for the determination of oxadiargyl in environmental and agricultural samples in combination with gas chromatography-mass spectrometry

Preparation of Durable Graphene-Bonded Titanium Fibers for Efficient Microextraction of Phthalates from Aqueous Matrices and Analysis with Gas Chromatography–mass Spectrometry

A porous carbon derived from amino-functionalized material of Institut Lavoisier as a solid-phase microextraction fiber coating for the extraction of phthalate esters from tea.

Preparation Of Solid-Phase Microextraction Fiber Coated With Single-Walled Carbon Nanotubes By Electrophoretic Deposition And Its Application In Extracting Phenols From Aqueous Samples

Poly-3,4-ethylenedioxythiophene Nanoclusters for High Effective Solid Phase Extraction.