High Performance Proton Exchange Membranes Obtained by Adjusting the Distribution and Content of Sulfonic Acid Side Groups.

Huiying Liao,Guyu Xiao,Deyue Yan

DOI: https://doi.org/10.1039/c3cc41200h

IF: 4.9

2013-01-01

Chemical Communications

Abstract:The proton conductivity and oxidation resistance as well as dimensional stability of hydrocarbon proton exchange membranes were simultaneously improved, achieving exciting overall properties.

What problem does this paper attempt to address?

Sulfonated Polyaryletherketone with Pendant Benzimidazole Groups for Proton Exchange Membranes

Jun Liang,Jiao Ge,Kai Wu,Qi Zhang,Jianli Wang,Zhibin Ye

DOI: https://doi.org/10.1016/j.memsci.2019.117626

IF: 9.5

2019-01-01

Journal of Membrane Science

Abstract:We synthesized a range of sulfonated polyaryletherketone (x%SCBI-SPAEK-6F) with pendant benzimidazole side groups at a tunable molar percentage (x within 5-15%) for potential application as proton exchange membrane (PEM). A systematic study had been undertaken to study the performance and the underlying structure-properties relationship of PEMs fabricated by those novel amphoteric polymers. It was found that the dimensional stability, oxidative stability and methanol resistance performance of x%SCBI-SPAEK-6F membranes were significantly improved with the increase of the benzimidazole content due to the acid-base interaction. In particular, the 5%SCBI-SPAEK-6F membrane exhibited a relative selectivity (10.5 x 10(3) S s cm(-3)) almost 20 times higher than that of Nafion117 membrane at 75 degrees C, demonstrating the significant promoted proton conductivity (0.35 S cm(-1)) and reduced methanol penetration (6 x 10(-7) cm(2) s(-1)) by the ionic barrier. With such superior performance, these polymers are promising for the fabrication of practical proton exchange membranes in commercial fuel cells.
Preparation on PVP Modiifed Acid-Base Composite High Temperature Proton Exchange Membrane

Lin Zhang,Xin Zhang,Chunhui Shen,Yuxing Guo,Ying Xie,Yuyang Jiang

DOI: https://doi.org/10.3969/j.issn.1001-3539.2018.06.008

2018-01-01

Abstract:Taking amino trimethylene phosphonic acid (ATMP) and 3-aminopropyltriethoxysilane (APTES) and polyvinyl pyrrolidone (PVP) serve as raw materials,ATMP/APTES acid-base composite proton exchanges membrane and PVP modified acid-base composite membranes were prepared by sol-gel method and characterized systematically by FTIR,SEM,TG–DSC and Autolab. The results show that the modifier PVP has a good consistency with proton membrane. The addition of PVP can improve the oxidative stability and dimensional stability water absorption of membrane to a certain extent. The proton conductivity is enhanced with increasing temperature,IEC and PVP content. The proton conductivity of the composite membrane with the mass fraction 2％ PVP is up to 1.73×10–2S/cm at 140℃under dry conditions. The ATMP/APTES/PVP has good thermal stability and can be oper-ated in the high temperature and low humidity environment.
Effect of “bridge” on the performance of organic-inorganic crosslinked hybrid proton exchange membranes via KH550

Hailan Han,Hai Qiang Li,Meiyu Liu,Lishuang Xu,Jingmei Xu,Shuang Wang,Hongzhe Ni,Zhe Wang

DOI: https://doi.org/10.1016/j.jpowsour.2016.11.066

IF: 9.2

2017-01-01

Journal of Power Sources

Abstract:A series of novel organic-inorganic crosslinked hybrid proton exchange membranes were prepared using sulfonated poly(arylene ether ketone sulfone) polymers containing carboxyl groups (C-SPAEKS), (3-aminopropyl)-triethoxysilane (KH550), and tetraethoxysilane (TEOS). KH550 acted as a “bridge” after reacting with carboxyl and sulfonic groups of C-SPAEKS to form covalent and ionic crosslinked structure between the C-SPAEKS and SiO2 phase. The crosslinked hybrid membranes (C-SPAEKS/K-SiO2) were characterized by FT-IR spectroscopy, TGA, and electrochemistry, etc. The thermal stability, mechanical properties and proton conductivity of the crosslinked hybrid membranes were improved by the presence of both crosslinked structure and inorganic phase. The proton conductivity of C-SPAEKS/K-SiO2-8 was recorded as 0.110 S cm−1, higher than that of Nafion® (0.028 S cm−1) at 120 °C. Moreover, the methanol permeability of the C-SPAEKS/K-SiO2-8 was measured as 3.86 × 10−7 cm2 s−1, much lower than that of Nafion® 117 membranes (29.4 × 10−7 cm2 s−1) at 25 °C.
Achieving Better Balance on the Mechanical Stability and Conduction Performance of Sulfonated Poly(ether Ether Ketone) Proton Exchange Membranes Through Polydopamine/polyethyleneimine Co-Modified Poly(vinylidene Fluoride) Nanofiber As Support

Jiale Chu,Ying Ou,Fan Cheng,Hai Liu,Nan Luo,Fuqiang Hu,Sheng Wen,Chunli Gong

DOI: https://doi.org/10.1016/j.ijhydene.2023.10.298

IF: 7.2

2024-01-01

International Journal of Hydrogen Energy

Abstract:In this work, the polyvinylidene fluoride (PVDF) electrospun fibers was applied as robust mechanical support and subsequently functionalized with polydopamine/polyethyleneimine (PDA/PEI) composite, then filled with sulfonated poly (ether ether ketone) (SPEEK) to obtain SPEEK-PDA/PEI@PVDF composite proton exchange membranes. The composite membranes achieved better balance on the mechanical stability and conduction performance, owing to enhanced interface interactions and compatibility between robust PVDF and conductive SPEEK. In wet conditions, the composite membrane exhibited excellent mechanically robust with tensile strength of 34 MPa and elongation at break of almost 200 %. Furthermore, the composite membranes also showed high structure and performance stability during the measurement of proton conductivity and fuel cell performances, it could hold stable proton conductivity of 48 mScm(-1) (at 80 degrees C) and maximum power density of 58.9 mWcm(-2). The durability test further confirmed the super operating stability of composite membrane, only 2.6 % reduction in open circuit voltage was observed during operated at 80 degrees C for 100 h.y
High performance sulfonated poly(phthalazinone ether phosphine oxide)s for proton exchange membranes

Huiying Liao,Ke Zhang,Guyu Xiao,Deyue Yan

DOI: https://doi.org/10.1016/j.memsci.2013.07.019

IF: 9.5

2013-01-01

Journal of Membrane Science

Abstract:A series of sulfonated poly(phthalazinone ether phosphine oxide)s with disulfonated moieties (dsPPEPO) were synthesized. Sulfonated poly(phthalazinone ether phosphine oxide)s with mono-sulfonated moieties (msPPEPO) were also prepared for comparative study. These two series of polymers represented two kinds of distribution modes of sulfonic acid side groups. The distribution mode of the sulfonic acid side groups within membranes could remarkably change their microstructure. As a result, dsPPEPO exhibited better dimensional and oxidative stability as compared to msPPEPO on condition of equal sulfonation degree. Moreover, the as-synthesized dsPPEPO showed enhanced proton conductivity further by increasing sulfonation degree while remaining excellent dimensional and oxidative stability. Therefore, the resulting membranes displayed excellent overall properties. For example, the dsPPEPO membrane with a sulfonation degree of 110% presented a lower swelling and much higher proton conductivity than those of Nafion 117. Its oxidative stability was also comparable to the highly durable aromatic PEMs.
Proton exchange composite membranes from blends of brominated and sulfonated poly(2,6-dimethyl-1,4-phenylene oxide)

Tongwen Xu,Dan Wu,Seokjun Seo,JungJe Woo,Liang Wu,SeungHyeon Moon

DOI: https://doi.org/10.1002/app.35494

IF: 3

2012-01-01

Journal of Applied Polymer Science

Abstract:New composite proton exchange membrane was prepared by mixing a 1-methyl-2-pyrrolidone (NMP) solution of sulfonated poly(2,6-dimethyl-1,4-phenylene oxide) (SPPO) in sodium form and brominated poly(2,6-dimethyl-1,4-phenylene oxide) (BPPO) for hydrophilic-hydrophobic balance, then casting the solution as a thin film, evaporating the solvent, and treating the membrane with aqueous hydrochloric acid. The resulting membranes were subsequently characterized using FTIR-ATR, SEM-EDXA, and TGA instrumentation as well as measurements of basic properties such as ion exchange capacity (IEC), water uptake, proton conductivity, methanol permeability, and single cell performance. Water uptake, IEC, proton conductivity, and methanol permeability all increased with a corresponding increase of SPPO content. By properly compromising the conductivity and methanol permeability, membranes with 60-80 wt % SPPO content exhibited comparable proton conductivity to that of Nafion (R) 117, with only half the methanol permeability, thereby demonstrating higher single cell performance. The membranes developed in this study could thus be a suitable candidate electrolyte for proton exchange membrane fuel cells (PEMFCs). (C) 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012
Proton exchange membrane deriving from sulfonated N-heterocyclic poly(aryl ether ketone)s containing ether-free proton conducting units and performing enhanced physicochemical stability and conduction properties

Qian Liu,Shouhai Zhang,Fanchen Sun,Peiqi Xu,Chenghao Wang,Lin Zhuo,Zijian Li,Kang Niu,Zhaoqi Wang,Xigao Jian

DOI: https://doi.org/10.1016/j.memsci.2023.122402

IF: 9.5

2024-02-01

Journal of Membrane Science

Abstract:Sulfonated aromatic polymer proton exchange membranes suffer from the trade-off relationship between physicochemical stability and proton conductivity hampering the membrane application in fuel cells. To bridge the effect, the high-performance membranes exhibiting excellent proton conduction behavior and good stability are constructed from sulfonated N-heterocyclic poly(aryl ether)s designed elaborately, in which the hydrophilic units are constructed by combining the high-density pendant benzenesulfonic groups and biphthalazindione structures without the introduction of weak linkage units like ether bonds. The twisted heterocyclic structures and the multiple interactions between heterocyclic structures and sulfonic groups enhance the physical stability and proton-conduction behavior with the highest conductivity of 256 mS cm−1 for the membranes. The membranes perform rupture time between 3.9 and 7.1 h in high temperature Fenton's oxidation test, exhibiting good chemical stability. The cells loading the membranes perform the maximum power density between 1.08 and 2.30 W cm−2. The above results verify the benefits of constructing ether-free heterocyclic hydrophilic units with high-density proton-conducting groups for the improvement of comprehensive membrane performance.

engineering, chemical,polymer science
Effective proton transport and anti-free radical oxidation: construction of interpenetrating network via co-crosslinking polybenzimidazole with proton conductors

Hui Guo,Xulei Zhi,Zhongfang Li,Lei Zhang,Peng Sun,Hongchang Pei

DOI: https://doi.org/10.1016/j.mtchem.2022.101009

IF: 7.613

2022-12-01

Materials Today Chemistry

Abstract:High temperature proton exchange membranes with good chemical stability and proton conductivity are desired for practical application. A crosslinkable allyl-cyanuric trisulfonic (ACSA) proton conductor and allyl-mPBI (APBI) are designed and synthesized to approach this aim. More stable basic sites (N) are endowed on ACSA and APBI through the reaction of oxidizable –NH groups to fundamentally achieve anti-free radical oxidation of membranes. The co-crosslinking of ACSA and APBI forms a monolithic crosslinked interpenetrating network in APBI-ACSA membranes, while the abundant basic sites construct dense hydrogen-ionic bond networks with –SO3H. The synergy of both networks locks ACSA in networks, avoids leaching and achieves uniform dispersion and high addition level of ACSA, thus providing good membrane stability of mechanical and dimensional. Molecular dynamics simulation shows that the microphase separation structure promotes the formation of continuous proton transport microchannels (including hydrogen-ionic bond network and hydration channel) over wide relative humidity (RH) ranges. Under 100%, 50% and 0% RH, the proton conductivity of APBI-ACSA(40) membrane is 0.158, 0.082 and 0.035 S/cm at 180 °C, respectively. There is almost no decay in conductivity after the durability tests. Meanwhile, APBI-ACSA membranes exhibited good fuel crossover resistance over Nafion membranes for both gas and liquid phase fuels.

chemistry, multidisciplinary,materials science
High-performance proton exchange membrane derived from N-heterocycle poly(aryl ether sulfone)s with ether-free hydrophilic blocks and exhibiting good stability and proton-conducting performance

Qian Liu,Kaiwen Wu,Shouhai Zhang,Lin Zhuo,Fanchen Sun,Chenghao Wang,Zijian Li,Yiping He,Yousi Chen,Wei Zhang,Xigao Jian

DOI: https://doi.org/10.1016/j.memsci.2024.123402

IF: 9.5

2024-10-14

Journal of Membrane Science

Abstract:The trade-off issue between proton conduction properties and stability is a constraint on the commercial application of non-fluorinated proton exchange membranes for fuel cells. To alleviate the issue, the multi-block N-heterocycle poly(aryl ether sulfone)s with ether-free hydrophilic blocks (b-SPDPESs), which is composited by diphenyl sulfone moieties and biphthalazindione structures with dense pendant benzenesulfonic groups, are developed to prepare high-performance membranes. The self-assembly effect of block copolymers not only improves the membrane stability but also constructs regular proton conduction channels. Moreover, the conduction channel consists of hydrophilic blocks without ether bonds, which effectively improves the tolerance of the membrane to radicals. The hydrogen-bond network between sulfonic groups and N-heterocycles in the channel improves the proton conduction efficiency, inhibits the swelling of the membrane, and improves the stability of the membrane. As a result, the swelling degree of b-SPDPESs membrane is only 15.8%, the proton conductivity is as high as 238 mS cm -1 , the membrane aging broken time at 80°C is between 4-6.6 h, and the fuel cells loading the membranes and feeding with hydrogen and air perform the max power density of between 0.65 - 1.25 W cm -2 . Modulating the sequence structure of chains and constructing multiblock polymers containing ether-free N-heretrocyclic blocks with sulfonic groups improve the stability of membranes while ensuring their proton conductivity.

engineering, chemical,polymer science
High conductive and dimensional stability proton exchange membranes with an all-carbon main chain and densely sulfonated structure

Jiayu Guan,Xi Sun,Huiting Yu,Jifu Zheng,Yuxuan Sun,Shenghai Li,Guorui Qin,suobo zhang

DOI: https://doi.org/10.2139/ssrn.4700730

IF: 9.5

2024-03-26

Journal of Membrane Science

Abstract:Sulfonated polyarylene membranes are demonstrated to be efficient as proton exchange membranes (PEMs) for proton exchange membrane fuel cells (PEMFCs) in clean energy conversion systems. In this study, we design and synthesize a series of sulfonated polyarylene with all-carbon backbones and densely sulfonated pendant groups, which can be prepared by copolymerization of 1,3-Disulfonic acid benzaldehyde, 1,1,1-trifluoroacetone and biphenyl under superacid-catalyzed conditions. Rigid, hydrophobic backbone and hydrophilic side chains make the membrane form good microphase separation morphology. The PEMs exhibit high proton conductivity (404 mS cm −1 ) and excellent dimensional stability (swelling ratio lower than 24% and water uptake lower than 40%) at 80 °C. Moreover, the PEMs show good oxidization stability (the retaining weight rate of membrane up to 99.2% for 1 h oxidative treatment), and the oxidization stability and degradation mechanism of Ar 3 CH in polymer backbone are also studied. The H 2 /O 2 fuel cell assembled with PEMs exhibited a maximum peak power density of 560 mW cm −2 . It indicates that all-carbon main chain and densely sulfonated structure show great potential for improving the performance of PEMs.

engineering, chemical,polymer science
Enhancement of comprehensive performance of high-temperature and low-humidity proton exchange membranes: Crosslinking of trifunctional proton conductor with branched polybenzimidazole

Xulei Zhi,Zhongfang Li,Peng Sun,Hongchang Pei,Wenjie Duan

DOI: https://doi.org/10.1016/j.memsci.2024.122711

IF: 9.5

2024-03-30

Journal of Membrane Science

Abstract:In order to improve the proton conductivity and antioxidant stability of proton exchange membranes (PEMs) at wide relative humidity (RH), composite membranes cross-linked with tribranched polybenzimidazole (TaPBI) and poly(azido-1-propanesulfonic acid −2,2′- methylsulfonic acid −5,5′-bis-benzimidazole) polyphosphazenes (PSBI) (TaPBI-PSBI) are prepared. TaPBI, as a branched polybenzimidazole, exhibits a large free volume. The trifunctional proton conductor PSBI-Na incorporates abundant flexible acidic groups and basic sites to enhance proton conductivity, and cross-linking groups to increase its binding strength with PBI. By casting and cross-linking, the proton conductivity, mechanical properties, and oxidation resistance of the TaPBI-PSBI membranes are significantly improved. The generation of cross-linked structures in the membranes is demonstrated by FT-IR. SEM shows that the surface of composite membrane is smooth and free of through holes. The elements are uniformly distributed. The TEM shows microphase separation occurs in the TaPBI-PSBI membrane, facilitating the formation of the continuous proton channels. The proton conductivity of TaPBI-PSBI (40) composite membrane reaches 0.170, 0.081, 0.059, and 0.037 S cm −1 at 180 °C, 100%, 50%, 30%, and 0% RH, respectively. The composite membrane is demonstrated the outstanding stability with the small decrease of proton conductivity and mass after durability testing of 96 h. The composite membrane exhibits high comprehensive performances as HT-PEM.

engineering, chemical,polymer science
Cation Exchange Membranes with Bi‐Functional Sites Induced Synergistic Hydrophilic Networks for Selective Proton Transport (Adv. Funct. Mater. 27/2023)

Yanran Zhu,Qian Chen,Yue Zhou,Xingya Li,Liang Ge,Tongwen Xu

DOI: https://doi.org/10.1002/adfm.202370169

IF: 19

2023-07-05

Advanced Functional Materials

Abstract:Selective Proton Transport In article number 2215109, Tongwen Xu, Liang Ge, Xingya Li, and co‐workers report a series of dibenzo‐18‐crown‐6 functionalized sulfonated poly(biphenyl alkylene) membranes. The membranes possess synergistic hydrophilic networks induced by bi‐functional sites (crown ether and sulfonic‐acid group), increasing selective proton transport, and providing efficient acid recovery in electrodialysis. It shows novel perspective to construct hydrophilic domain with crown ether in ion exchange membranes.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Design and Synthesis of Comb‐Like Bisulfonic Acid Proton Exchange Membrane with Regulated Microstructure

Qian Wang,Linjian Sang,Lei Huang,Jiayu Guan,Huiting Yu,Jifu Zheng,Qifeng Zhang,Guorui Qin,Shenghai Li,Suobo Zhang

DOI: https://doi.org/10.1002/adfm.202316506

IF: 19

2024-01-01

Advanced Functional Materials

Abstract:The design and synthesis of proton exchange membranes (PEMs) with controllable microstructure and sulfonation degree play a crucial role in enhancing their performance and expanding their application. In this study, the disulfonic acid monomer is designed and prepared to synthesize the comb-like disulfonic PEMs with controllable ion exchange capacity. The results show that the side chain structure and more concentrated sulfonic acid groups facilitate the aggregation of sulfonic acid groups in the polymer, improve the microphase separation morphology of PEMs, and increase the ionic conductivity. The proton conductivity of the DS-PXIDI-60 membrane is approximately 300 mS cm-1. The PEMs with controllable microstructure are prepared by introducing comonomers, including 9,9-dimethylxanthrene, biphenyl, and p-terphenyl, with different reactivity, spatial structure, and solubility. Biphenyl is copolymerized to form a copolymer with an alternating structure, and 9, 9-dimethylxanthrene is copolymerized to form a random copolymer. In addition, it is worth noting that p-terphenyl is copolymerized to form a microblock structure of the copolymer, with more excellent comprehensive properties. DS-PXITp-60 exhibits better performance than Nafion 212 in redox-flow batteries and fuel cells. Therefore, such molecular design and synthesis strategies provide a reference guide for the development of high-performance PEMs. A new type of disulfonic monomer with comb structure is designed, it is directly prepared into proton exchange membranes (PEMs), avoiding the use of sulfonating agent. The ion exchange capacity and microstructure of PEMs can be precisely adjusted by adjusting the proportion and structure of the comonomers. The PEMs exhibit better performance than Nafion-212 in redox-flow batteries and fuel cells. image
High Performance Ion Exchange Membranes Prepared Via Direct Polyacylation of Racemic and (s)‐1,1′‐binaphthyl‐based Cationic/Anionic Monomers

Zhenghui Zhang,Tongwen Xu

DOI: https://doi.org/10.1002/mame.201800547

2019-01-01

Macromolecular Materials and Engineering

Abstract:Side-chain-type sulfonated/quaternized aromatic polyelectrolytes with precisely controlled contents of ionized groups are successfully synthesized via direct polyacylation of sulfonated/quaternized monomers based on 2,2 '-dihydroxy-1,1 '-binaphthyl (DHBN). Both proton exchange membranes (PEMs) and anion exchange membranes (AEMs) of the corresponding polyelectrolytes exhibit outstanding properties. Proton conductivity (116 mS cm(-1) at 30 degrees C) higher than Nafion 115 for the PEMs and OH- conductivity (28.5-53.7 mS cm(-1) at 30 degrees C) comparable to Tokuyama A901 for the AEMs are accomplished. In addition, the AEMs can withstand 60 days' aging in 1 mol L-1 NaOH at 60 degrees C without degradation, as proved by H-1 NMR. More intriguingly, when starting from optically active (S)-DHBN instead of racemic DHBN, an enhancement in proton conductivity of PEMs is observed for the first time, which opens a new door to optically active ion exchange membranes.
Molecular-Level Modification of Sulfonated Poly(arylene ether ketone sulfone) with Polyoxovanadate-Ionic Liquid for High-Performance Proton Exchange Membranes

Wenjing Li,Yishan Li,Yanchao Zhang,Jiahao Lu,Yuanlong Wu,Jiaran Song,Jinsheng Li,Zhe Wang

DOI: https://doi.org/10.1021/acsami.4c09126

IF: 9.5

2024-08-18

ACS Applied Materials & Interfaces

Abstract:In this work, a proton-conductive inorganic filler based on polyoxovanadate (NH(4))(7)[MnV(13)O(38)] (AMV) and 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl) imide (EMIM TFSI) was synthesized for hybridization with sulfonated poly(aryl ether ketone sulfone) (SPAEKS) to address the "trade-off" between high proton conductivity and mechanical strength. The novel inorganic filler AMV-EMIM TFSI (AI) was uniformly dispersed and stable within the polymer matrix due to the enhanced ionic...

materials science, multidisciplinary,nanoscience & nanotechnology
Highly proton-conductive and low swelling polymeric membranes achieved by hydrophilic covalent cross-linking

Chengzhi Cui,Peng Sun,Yan Wang,Hui Ding,Zhuowei Qu,Bo Zhang,Yidan Tian,Zhongfang Li

DOI: https://doi.org/10.1016/j.jcis.2024.06.047

2024-10-15

Abstract:Proton exchange membranes (PEMs) applied in fuel cell technology suffer from the trade-off between fast proton conduction and durable operation involving dimensional stability, mechanical strength, and oxidative resistance. To address this issue, a novel branched polybenzimidazole (brPBI) was synthesized, covalently cross-linked with (3-chloropropyl)triethoxysilane (CTS), and doped with a novel proton conductor FeATMP to prepare brPBI-CTS/FeATMP membranes. The branching degree of brPBI was optimized to achieve high molecular weight while the branching structure offered high free volume, abundant end-groups, and self-cross-linking moiety that enhanced proton conduction and dimensional/mechanical/oxidative stability. Covalent cross-linking with CTS enhanced the dimensional, mechanical, and oxidative stability while improving the water-assisted proton conduction owing to the hydrophilic nature of siloxane structure formed. At 180 ℃, the proton conductivity of the brPBI3-CTS/FeATMP composite membrane reached 0.136, 0.073, and 0.041 S cm-1 at 100 % RH, 50 % RH, and 0 % RH, respectively, while its swelling ratio after immersion in water at 90 ℃ for 24 h was 4.69 %. The performance of the membranes demonstrated that construction of hydrophilic structure by covalent cross-linking was a successful strategy to break the trade-off effect for PEMs.
SPES‐SiO2 Hybrid Proton Exchange Membranes from in Situ Sol–gel Process of Negatively Charged Alkoxysilane

Cuiming Wu,Xinle Xiao,Wenchang Xiao,Yonghui Wu,Peng Cui,Tongwen Xu

DOI: https://doi.org/10.1002/app.34152

IF: 3

2011-01-01

Journal of Applied Polymer Science

Abstract:One type of negatively charged alkoxysilane, that is, sulfonated 3-(mercaptopropyl)trimethoxysilane (SMPTS), has been developed from 3-(mercaptopropyl)trimethoxysilane (MPTS) and hydrogen peroxide. SMPTS is used to modify sulfonated poly(ether sulfone) (SPES) through in situ sol-gel process. The membranes with proper SMPTS dosage show enhanced ion exchange capacity (IEC), hydrophilicity, mechanical strength, chemical stability, and proton conductivity, which prove that SMPTS is an effective modifier for preparing proton-exchange hybrid membranes. With MPTS of 5-20%, the hybrid membranes exhibit IEC 1.34-1.50 mmol g(-1), thermal stability 264-316 degrees C, and proton conductivity 0.0015-0.0102 S cm(-1) and thus recommended for potential application in fuel cells. (c) 2011 Wiley Periodicals, Inc. J Appl Polym Sci 122: 313-320, 2011
Sulfonated Poly(arylene Thioether Phosphine Oxide)/sulfonated Benzimidazole Blends for Proton Exchange Membranes

Yunlong Tan,Ke Zhang,Huiying Liao,Di Liu,Guyu Xiao,Guoming Sun,Deyue Yan

DOI: https://doi.org/10.1016/j.memsci.2011.01.057

IF: 9.5

2011-01-01

Journal of Membrane Science

Abstract:Blends of sulfonated poly(arylene thioether phosphine oxide)s and sulfonated polybenzothiazoles exhibited excellent overall properties as proton exchange membranes.
Phosphorylated poly(ethylene- co -vinyl alcohol) doping for enhanced proton conductivity and mechanical properties of side chain–type sulfonated poly(aryl ether ketone) proton-exchange membranes

Tiandu Dong,Zetian Zhang,Hao Liu,Yingjiao Deng,Weixia Liu,Yunxi Li,Yichen Liu,Mingzheng Zhou,Zihan Meng,Haolin Tang

DOI: https://doi.org/10.1016/j.memsci.2023.122298

IF: 9.5

2023-11-28

Journal of Membrane Science

Abstract:Phosphorylated poly (ethylene- co -vinyl alcohol) (PEVOH) was synthesized and blended with side chain–type sulfonated poly (aryl ether ketone) (SPAEK) to prepare SPAEK proton-exchange membranes with improved physicochemical and electrochemical properties. The results indicate that PEVOH doping helps improve the mechanical properties and proton conductivity of the membranes. The addition of PEVOH not only enhances proton transport but also provides proton transport channels for the membranes at a high temperature and low humidity, leading to excellent fuel cell performance and low ohmic resistance. The interaction between sulfonic acid and phosphonic acid side chain groups leads to the excellent nano-phase separation under microscopic morphology. This forms a large hydrogen bonding network between the acidic and amphoteric groups, which facilitates proton transport at low relative humidities.

engineering, chemical,polymer science
Proton transfer efficiency enhanced over wide relative humidity: Etidronic acid-modified polyphosphazenes cross-linked polybenzimidazoles membranes

Ping Li,Hui Guo,Peng Sun,Xulei Zhi,Zhongfang Li

DOI: https://doi.org/10.1016/j.memsci.2023.121973

IF: 9.5

2023-11-01

Journal of Membrane Science

Abstract:To enhance the proton conductivity and oxidative stability of the proton exchange membrane, an effective strategy to construct robust high-temperature PEMs (HT-PEMs) is proposed. The polyoxy(etidronic acid)phazenes cross-linked m-polybenzimidazole membranes (POHP-mPBI) are prepared by solution casting, thermal-crosslinking and acidification. Polyoxy(etidronic acid sodium)phazenes (Na–POHP) is cross-linkable proton conductors by partially phosphonic acid functionalized polyphosphazenes, which ensures proton transport while retaining the cross-linked groups. After covalent cross-linking between Na–POHP and mPBI, the cross-linked macromolecular structure stably locks the proton conductor in the polymer matrix, which ensures the construction of the proton transfer pathway at wide relative humidity (RH). The molecular dynamics simulation was conducted to verify the hydrogen bonds network with the POHP-mPBI membrane. The POHP-mPBI cross-linked membranes exhibit good oxidative stability, mechanical strength, proton conductivity and low fuel transmembrane permeability. At 180 °C and different RH (100% RH, 50% RH, 30% RH and 0 RH), the proton conductivity of POHP(50)-mPBI membrane is 0.150, 0.076, 0.055 and 0.048 S cm−1, respectively. After the water washing for 96 h, the durability of proton conductivity and weight loss shows a rare decline. The incorporation of proton conductors (POHP) into the PBI matrix by cross-linking is a perspective method to enhance the comprehensive performance of HT-PEM.

engineering, chemical,polymer science

High Performance Proton Exchange Membranes Obtained by Adjusting the Distribution and Content of Sulfonic Acid Side Groups.

Sulfonated Polyaryletherketone with Pendant Benzimidazole Groups for Proton Exchange Membranes

Preparation on PVP Modiifed Acid-Base Composite High Temperature Proton Exchange Membrane

Effect of “bridge” on the performance of organic-inorganic crosslinked hybrid proton exchange membranes via KH550

Achieving Better Balance on the Mechanical Stability and Conduction Performance of Sulfonated Poly(ether Ether Ketone) Proton Exchange Membranes Through Polydopamine/polyethyleneimine Co-Modified Poly(vinylidene Fluoride) Nanofiber As Support

High performance sulfonated poly(phthalazinone ether phosphine oxide)s for proton exchange membranes

Proton exchange composite membranes from blends of brominated and sulfonated poly(2,6-dimethyl-1,4-phenylene oxide)

Proton exchange membrane deriving from sulfonated N-heterocyclic poly(aryl ether ketone)s containing ether-free proton conducting units and performing enhanced physicochemical stability and conduction properties

Effective proton transport and anti-free radical oxidation: construction of interpenetrating network via co-crosslinking polybenzimidazole with proton conductors

High-performance proton exchange membrane derived from N-heterocycle poly(aryl ether sulfone)s with ether-free hydrophilic blocks and exhibiting good stability and proton-conducting performance

High conductive and dimensional stability proton exchange membranes with an all-carbon main chain and densely sulfonated structure

Enhancement of comprehensive performance of high-temperature and low-humidity proton exchange membranes: Crosslinking of trifunctional proton conductor with branched polybenzimidazole

Cation Exchange Membranes with Bi‐Functional Sites Induced Synergistic Hydrophilic Networks for Selective Proton Transport (Adv. Funct. Mater. 27/2023)

Design and Synthesis of Comb‐Like Bisulfonic Acid Proton Exchange Membrane with Regulated Microstructure

High Performance Ion Exchange Membranes Prepared Via Direct Polyacylation of Racemic and (s)‐1,1′‐binaphthyl‐based Cationic/Anionic Monomers

Molecular-Level Modification of Sulfonated Poly(arylene ether ketone sulfone) with Polyoxovanadate-Ionic Liquid for High-Performance Proton Exchange Membranes

Highly proton-conductive and low swelling polymeric membranes achieved by hydrophilic covalent cross-linking

SPES‐SiO2 Hybrid Proton Exchange Membranes from in Situ Sol–gel Process of Negatively Charged Alkoxysilane

Sulfonated Poly(arylene Thioether Phosphine Oxide)/sulfonated Benzimidazole Blends for Proton Exchange Membranes

Phosphorylated poly(ethylene- co -vinyl alcohol) doping for enhanced proton conductivity and mechanical properties of side chain–type sulfonated poly(aryl ether ketone) proton-exchange membranes

Proton transfer efficiency enhanced over wide relative humidity: Etidronic acid-modified polyphosphazenes cross-linked polybenzimidazoles membranes