Abstract:Methanol is an attractive oxygenate increasingly used as primary fuel for dual-fuel combustion technology yielding beneficial thermal-efficiency and emissions in modern engines. As such, it is significant to fundamentally understand the autoignition behavior of methanol/diesel mixtures. This study measured the ignition delay times (IDTs) of methanol/diesel blends with different mixing ratios (30%, 50%, 70% methanol by mol.) on a heated shock tube and a heated rapid compression machine at temperatures of 650-1450 K, pressures of 6-20 bar, and equivalence ratios of 0.5, 1.0 and 2.0. The typical two-stage ignition characteristics with the negative temperature coefficient response were observed for dual-fuel mixtures. In general, both the total and first-stage IDTs decrease with the increment of pressure and equivalence ratio as well as diesel proportion in mixtures. The simulation results performed with a published detailed mechanism in conjunction with a tri-component diesel surrogate demonstrate generally good agreement with the experimental data at all test conditions. Moreover, a crossover of IDTs occurs at a higher temperature (similar to 1500 K) for varying equivalence ratios, and experiment and simulation both exhibit a non-linear mixing effect of methanol addition on diesel ignition. Interestingly, simulation results clearly suggest a crossover (similar to 940 K) for mixtures with varying methanol content at an intermediate-temperature, where the IDT of the mixture with a lower methanol ratio becomes longer as the temperature is higher than that of the crossover. Furthermore, brute-force sensitivity analyses assisted with reaction path analysis were conducted to gain deeper insights into the autoignition chemistry of dual-fuel mixtures, especially for the chemical interaction between both fuels during the low-temperature oxidation process. It is found that methanol hardly generates center dot OH, whereas center dot OH is mainly produced by the low-temperature reaction pathways of diesel. Thus, center dot OH is the bridge for both fuels during the ignition process. At the high methanol ratio, the H-abstraction of diesel is mainly via center dot HO2 while CH3OH consumes a large percentage of center dot OH. Consequently, the competition between methanol and diesel for center dot OH radicals inhibits the overall reactivity of reaction network. In addition, the original data reported here lay a foundation for the development and validation of more accurate and robust dual-fuel kinetic schemes. (C) 2021 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Droplet Vaporization Characteristics of Multicomponent Mixtures of Methanol and Gasoline Surrogate in Opposed Stagnation Flows

Vaporisation Characteristics of Methanol, Ethanol and Heptane Droplets in Opposed Stagnation Flow at Low Temperature and Pressure

Study on Combustion Characteristics of a DI Diesel Engine Operating on Diesel/Methanol Blends

Autoignition Behavior of Methanol/diesel Mixtures: Experiments and Kinetic Modeling

Quantitative mixing measurements and stochastic variability of a vaporizing gasoline direct-injection spray

Simulation Study on the Impact of Injection Strategies on the Performance of Methanol–Gasoline Dual-Fuel Engines

An Experimental and Numerical Investigation on Characteristics of Methanol and Ethanol Sprays from a Multi-hole DISI Injector

Experimental Investigation of the Evaporation Characteristics of the Fuel in a Direct-Injection Spark Ignition Engine Subjected to a Direct-Start Process

Effects of Injection Parameters and EHN Mixing on the Combustion Characteristics of Fueling Pure Methanol in a Compression Ignition Engine

Investigation of Methanol Ignition Phenomena Using a Rapid Compression Machine

A Reduced Kinetics Model for the Oxidation of Transcritical/Supercritical Gasoline Surrogate/Ethanol Mixtures Using Real Gas State Equations

Understanding the Antagonistic Effect of Methanol As a Component in Surrogate Fuel Models: A Case Study of Methanol/n-Heptane Mixtures

An Experimental Investigation on the Vaporization and Combustion of Methanol and Ethanol Droplets

Characteristics of Ethanol, Butanol, Iso-Octane and Gasoline Sprays and Combustion from a Multi-Hole Injector in a DISI Engine

Characteristics of Evaporating Spray for Direct Injection Methanol Engine: Comparison between Methanol and Diesel Spray

Experimental and numerical study on a SI engine fueled with gasohol and dissociated methanol gas blends at lean conditions

The Effects of Methanol Fraction on the Azeotropic Behaviors of Methanol/Gasoline Mixtures

A Reduced Combustion Kinetic Model for the Methanol-Gasoline Blended Fuels on SI Engines

State-of-the-art modeling of two-stage auto-ignition: Turbulence, evaporation and chemistry effects

CFD unified approach under Eulerian-Lagrangian framework for methanol and gasoline direct injection sprays in evaporative and flash boiling conditions

Experimental and Numerical Investigation of Laminar Flame Characteristics of Isooctane/air Mixtures at High Preheating Temperatures and H2O Dilution Ratios