Abstract:This study reports electrolytic degradation and kinetic modeling of electrolytic degradation of ammonia using Ti/IrO2. The experimental and modeling results are compared with those previously obtained using Ti/RuO2 anode. Synthetic solution containing predetermined ammonia concentration and the raw municipal wastewater collected after the aerobic or the anaerobic treatment were used in different sets of experiments. The experimental conditions varied for electrolytic degradation of ammonia present in the synthetic feed were initial chloride concentration, initial pH and applied current density. The results show that the ammonia removal followed pseudo zero-order kinetics. The current density (j) and the initial Cl- concentration ([Cl-]) affected the constant of the pseudo zero-order kinetics, expressed as k(Ti/IrO2) = 0.0020[Cl-]j+0.4848 and k(Ti/RuO2) = 0.0026[Cl-]j - 0.7417. The ammonia removal rate averaged at 8.5 using Ti/IrO2 and was comparable to the rate (11.7 mg NL-1 h(-1)) obtained using Ti/RuO2 anode, at 15.4 mA cm(-1) current density, 300 mg L-1 Cl- and pH of 7. Higher current density and as well as the chloride concentration resulted in greater ammonia degradation. On the other hand, pH did not seem to have any effect on electrolytic degradation of ammonia. More than 95% ammonia degradation in municipal wastewater effluents collected after aerobic or anaerobic treatment was achieved. The ammonia nitrogen in the electrolytically treated wastewater effluents collected at the end of aerobic and anaerobic environments were 0.9, 0.5 mg N L-1 using Ti/IrO2 and 0.5,0.2 mg N L-1 by using Ti/RuO2 anodes, respectively. Published by Elsevier B.V.

Electrochemical denitrification and kinetics study using Ti/IrO2-TiO2-RuO2 as the anode and Cu/Zn as the cathode

Efficient Nitrogen Removal by Simultaneous Photoelectrocatalytic Oxidation and Electrochemically Active Biofilm Denitrification

Modulation of Charge Distribution Enabling CuNi Nano-Alloys for Efficient Ammonia Oxidation Reaction to Nitrite Production

In Situ Loading of Cu2O Active Sites on Island-like Copper for Efficient Electrochemical Reduction of Nitrate to Ammonia.

Electrochemical Reduction of Nitrate Using Various Anodes and a Cu/Zn Cathode

Optimization of electrochemical denitrification process parameters with Box-Behnken design

Simultaneous reduction of nitrate and oxidation of by-products using electrochemical method.

Efficient Electrochemical Reduction of Nitrate to Nitrogen Using Ti/IrO2–Pt Anode and Different Cathodes

Efficient electrocatalysis for denitrification by using TiO2 nanotube arrays cathode and adding chloride ions

Fabrication and Characterization of Cu/Ti Bilayer Nanoelectrode for Electrochemical Denitrification

Electrochemical denitrification by a recyclable cobalt oxide cathode: Rapid recovery and selective catalysis

Achieving efficient and stable electrochemical nitrate removal by in-situ reconstruction of Cu2O/Cu electroactive nanocatalysts on Cu foam

Ti Nano Electrode Fabrication for Electrochemical Denitrification Using Box–Behnken Design

Improvement on Electrochemical Reduction of Nitrate in Synthetic Groundwater by Reducing Anode Surface Area

Treatment of nitrate contaminated water using an electrochemical method.

Electrochemical Removal of Nitrate by Cu/Ti Electrode Coupled with Copper-Modified Activated Carbon Particles at a Low Current Density.

Design and Applications of Ti Nano-Electrode for Denitrification of Groundwater

Low-nitrite generation Cu–Co/Ti cathode materials for electrochemical nitrate reduction

The Improvement on Total Nitrogen Removal in Nitrate Reduction by Using a Prepared CuO-Co3O4/Ti Cathode

Electrochemical Behavior of Ti-Based Nano-Electrode for Highly Efficient Denitrification in Synthetic Groundwater

Kinetic study of electrolytic ammonia removal using Ti/IrO2 as anode under different experimental conditions.