Abstract:Large volume cubic press is one of the most popular high pressure devices which can produce pressures up to about 7 GPa. It is well known experimentally that the enhancing of the maximum pressure generated in the large volume cubic press has attracted wide attention among scientists and engineers because the higher pressure is capable of synthesizing some materials with interesting properties. In the large volume cubic press, pyrophyllite is typically used as a pressure-transmitting medium. A specimen immersed in such a solid experiences a generalized stress state. The pressure distribution in pyrophyllite is an important parameter for characterizing the sample environment and designing the experiments at high pressure. There is a need for the quantitative measurement of pressure gradients in the pyrophyllite pressure medium, so that the accurate experimental data under high pressure can be obtained. In the large volume cubic apparatus (68 MN), we put a circuit into the high pressure cubic cell, so that the pressures at various positions can be measured by using the phase transitions in Bi, Tl and Ba. In the present work, the relationship between the total press load and the press load allocated to the anvil face, and the relationship between the total press load and the press load allocated to gaskets are established at room temperature. The results show that with the increase of the total press load, the load allocated to the gaskets is increased sharply, while the curve of load allocated to the anvil face versus total press load reaches a plateau, which results in the cell pressure reaching upper limit when the cell pressure reaches up to about 5 GPa. According to the experimental results, the stress state of the cubic cell under high pressure is analyzed and the reason why the pressure generated in the large volume cubic chamber is difficult to exceed 7 GPa is explained. Based on the geometrical structure of the cubic cell, the scheme to increase the upper pressure limit for cubic cell by using the material with high bulk modulus as the pressure transmitting medium and the material with low bulk modulus as the gasket, is proposed. Additionally, the method of calculating the pressure values at different positions along the axis of symmetry in the cubic cell is given through the quantitative calibration of the pressure gradient in the axial direction of the cubic cell. This method can provide more accurate pressure data for high pressure experiments.

Mechanical Behavior of Cellular Borosilicate Glass with Pressurized Ar-Filled Closed Pores

Force Analysis and Pressure Quantitative Measurement for the High Pressure Cubic Cell

Structure and thermal conductivity of high-pressure-treated silica glass. A molecular dynamics study

Influence of Gas Pressure on the Surface Composition of Capsule-Free HIPed Borosilicate Glass

High Porosity Glass Foams from Waste Glass and Compound Blowing Agent

A Novel Method for Preparing Phase-Separated P2O5–Al2O3 Glass with High Young's Modulus

Atomic-Scale Insights into the Effects of the Foaming Degree on the Glass–Ceramic Matrix Derived from Waste Glass and Incineration Bottom Ash

Mechanical and Microstructural Response of Densified Silica Glass under Uniaxial Compression: Atomistic Simulations?

Producing light, strong foam glass under a low sintering temperature with insights from molecular simulations

Highly Porous Alumina Cellular Ceramics Bonded by In-Situ Formed Mullite Prepared by Gelation-Assisted Al2O3–Si Particle-Stabilized Foams

Glass Molding for Microstructures

First Principles Calculations of Stress-Induced Structural Changes of Supercooled Borosilicate Glass

Preparation, Characterization, and Mechanical Properties of Microcellular Poly(Aryl Ether Ketone) Foams

Preparation of Porous Glass-ceramic with Controlled Pore Size and Porosity by Adding Porosifier

Thermoplastic gas pressure forming of bulk metallic glass sheets under biaxial tension

Fabrication of TiZr-based bulk metallic glass foams with different gradient porosities for biomedical application

Preparation of Ultralight Glass Foams Via Vacuum-Assisted Foaming

Densification of Sodium and Magnesium Aluminosilicate Glasses at Ambient Temperature: Structural Investigations by Solid-state Nuclear Magnetic Resonance and Molecular Dynamics Simulations

Structural Aspects of Ambient-Temperature Densification of Highly Crack-Resistant Borosilicate and Aluminoborosilicate Glasses: Two Case Studies Examined by Solid-State NMR

Filling Hollow Glass Microspheres with Ar by Method of Gas Diffusion

Strength, Anisotropy, and Preferred Orientation of Solid Argon at High Pressures.