Abstract:The as-cast Al-4.6Mg alloy was subjected to deformation and sensitization–desensitization heat treatment, and then the microstructure and the enhancement mechanism of Sr were investigated by optical microscopy, scanning electron microscopy–energy-dispersive spectroscopy, electron backscatter diffraction, and transmission electron microscopy. The precipitation phases of Al-4.6Mg alloy were mainly β-Al3Mg2, Al6Mn, and Al6(Mn Cr), and the nanoscale precipitation phases were Al3Mn and Al11Mn4. The formation of β-Al3Mg2 was hindered by the addition of 0.1 wt.% Sr. In addition, the precipitate phase Al4Sr and the nano-sized precipitate phase τ-Al38Mg58Sr4 were uniformly distributed in the spherical matrix. The addition of Sr promoted the redissolution of Mg atoms in Al-4.6 Mg alloy, increasing the solubility of Mg in the α-Al matrix from 4.7 wt.% to 5.1 wt.%. The microstructure analysis showed that Sr addition inhibited the recovery and recrystallization of the alloy because the Sr element elevated the recrystallization temperature. As a result, the grain deformation was intensified, the grain size was decreased from 6.96 μm to 5.39 μm, the low-angle grain boundaries were increased from 78.7 at % to 84.6 at %, and the high-angle grain boundaries were increased from 21.3 at % to 15.4 at %. Furthermore, the mechanical properties of the alloy were significantly improved, and the plasticity degraded after the addition of the Sr element. The yield strength of the alloy was enhanced mainly through fine grain strengthening, dispersion strengthening, solid solution strengthening, and working hardening. The strengthening mechanisms were analyzed in detail.

An Investigation on Hot-Cracking Mechanism of Sr Addition into Mg–6Al–0.5Mn Alloy

Effect of Cu Additions on Microstructure, Mechanical Properties and Hot-Tearing Susceptibility of Mg-6Zn-0.6Zr Alloys

Effect of Al Content on Hot Tearing Susceptibility of Mg–5Zn–0.6Mn–xAl–0.6Zr Alloys

An approach to studying the hot tearing mechanism of alloying elements in ternary Mg-Zn-Al alloys

Effect of Al Content on Hot-Tearing Susceptibility of Mg-10Zn- x Al Alloys

Study on the Hot Tearing Susceptibility of Mg-4Zn-xSn-1Ca Alloys

Effect of addition of minor amounts of Sb and Gd on hot tearing susceptibility of Mg-5Al-3Ca alloy

Effect of Sr on Microstructure and Strengthening Mechanism of Al-4.6Mg Alloy

Hot Tearing Behavior of Mg-4Zn-xSn-0.6Zr Alloys

Effects of Mn Addition on the Microstructure and Mechanical Properties of Cast Mg–9Al–2Sn (wt.%) Alloy

Hot Tearing Behaviors and In-Situ Thermal Analysis of Mg-7Zn-xCu-0.6Zr Alloys

Effects of Sr content on the microstructure and mechanical properties of cast Al–12Si–4Cu–2Ni–0.8Mg alloys

Effect of Sb Addition on Hot Tearing Susceptibility and Mechanical Properties of Mg–7Al–1Ca–xSb (x = 0, 0.5, 1, 1.5, and 2 wt.%) Alloys

Hot-tearing Susceptibility of Mg–9Al–xZn Alloy

Influence of Alloying Elements on Hot Tearing Susceptibility of Mg–Zn Alloys Based on Thermodynamic Calculation and Experimental

Influence of Al Addition on the Microstructure and Mechanical Properties of Mg-Zn-Sn-Mn-Ca Alloys

Alloying effect of Mg on microstructure and mechanical properties at 300 °C of Al–5Cu–1Mn–0.5Ni heat-resistant alloy

Enhanced Strength by Precipitate Modification in Wrought Mg–Al–Ca Alloy with Trace Mn Addition

The Influence of Al–10Sr Or/ and Al–5Ti–1B on Microstructure and Mechanical Properties of Al–12Si–4Cu–2Ni–0.8 Mg Alloys

Influence of the Mg Content on the Microstructure and Mechanical Properties of Al-xMg-2.0Si-0.6Mn Alloy

Influence of Mn Addition on the Microstructure and Mechanical Properties of a Directionally Solidified Γ-Tial Alloy