Abstract:This paper studies the phenomenon of fiber alignment during the extrusion process. The fiber alignment is largely dependent on shapes of dies and the compression as well as the shear force generated in the extruder. The fiber alignment orientation, of course, would lead to direction dependency of the tensile properties of fiber-reinforced cement (FRC) extrudates. Such a dependency has been investigated in present study. It is found that when fiber volume ratio is small, say 1% of the glass fiber, the majority of the fiber can be aligned in the extrusion direction. As a result, the tensile strength of the thin plate along the extrusion direction is much higher than that along the transverse direction. When the total fiber volume ratio is increased to 2% or 4%, the fiber volume along the transverse direction is largely increased although the percentage of the fiber aligned along the extrusion direction is still higher. Thus, the tensile strength at a transverse direction can be significantly enhanced. In fact, the tensile strength of the samples along the transverse direction is almost the same as that along the extrusion direction when the fiber volume ratio reaches 2%. Furthermore, the strength of the sample at the extrusion direction does not increase proportionally to the fiber volume ratio. For the comparison purpose, plain sheets without any fibers have been prepared by both casting and extrusion. Mechanical properties of the sheets have also been tested and the test results show that extrusion process and fiber addition do have effects on enhancing the tensile properties. Polymer coating on the surface of the samples has also been used to improve the tensile properties of the extrudates with low fiber volume ratio, which shows some promising results.

Effect of Dynamical Converging Channels on Fiber Organization and Damage During Vane Extrusion of Sisal Fiber‐reinforced Polypropylene Composites

Composites of Sisal Fiber/polypropylene Based on Novel Vane Extruder: Effect of Interface and Damage on Mechanical Properties

Fiber alignment and property direction dependency of FRC extrudate

Study on Properties of Sisal Fiber Reinforced PP Composites Prepared by Vane Extruder

A 3D finite element model to simulate progressive damage in unidirectional- and woven-fibre thermoplastic discontinuous-long-fibre composites

Preparation of Polypropylene/Sisal Fiber Composites and Study on the Fiber Orientation

Effect of Fiber Morphology on Rheological Properties of Plant Fiber Reinforced Poly(Butylene Succinate) Composites

Effect of Initial Fiber Length on the Rheological Properties of Sisal Fiber/Polylactic Acid Composites

Effect of processing parameters on friction and damage of carbon yarn during three-dimensional weaving

Influences of Fiber Volume Content on the Mechanical Properties of 2D Plain Carbon-Fiber Woven Composite Materials

Effect of Vane Extruder on Processability and Mechanical Properties of PBS/Lignin Biocomposites

Fiber Breakage and Dispersion during Long Glass Fiber Reinforced Polypropylene Processing

Effects of Dynamic Elongational Flow on the Dispersion and Mechanical Properties of Low‐density Polyethylene/nanoprecipitated Calcium Carbonate Composites

Study on Effect of Extrusion Velocity on Composites Liquid-Solid Extrusion Process Using 3D Thermo-Mechanical Simulation

Parametric Numerical Ninvestigation of Out-of-plane Compression Properties and Damage Mechanism of Fine Weave Pierced C/C Composites

Structural Properties and Mechanical Behavior of Injection Molded Composites of Polypropylene and Sisal Fiber

Strain Rate Dependent Deformation of a Polymer Matrix Composite with Different Microstructures Subjected to Off-Axis Loading

The effect of fiber yarns structure on the mechanical properties of natural fiber reinforced composites

Effect of Needled Structures on In-Plane Tensile Behaviors of 2.5D-Cf/mg Composites Fabricated by the Liquid-Solid Extrusion and Vacuum Pressure Infiltration Process

Mechanical properties and failure modes of polypropylene fiber-reinforced foamed concrete subjected to high strain rates and large compressive deformation: effects of fiber content and length

EFFECTS OF FIBER LENGTH AND ORIENTATION DISTRIBUTIONS ON THE MECHANICAL PROPERTIES OF SHORT-FIBER-REINFORCED POLYMERS