Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Dramatic influence of curing temperature on micro-nano structure transform of HNBR filled with zinc dimethacrylate

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

The Curing Behavior and Properties of Diglycidyl Ether of 4,4′-Bis(4-hydroxybenzoyloxy)-3,3′,5,5′-tetramethylbiphenyl and Its Composites with Multi-Wall Carbon Nanotubes

Cure kinetics and morphology of natural rubber reinforced by the in situ polymerization of zinc dimethacrylate

Study on mechanical properties of elastomers reinforced by zinc dimethacrylate

A new strategy for improving high‐temperature mechanical properties of HNBR/ZDMA composites through polymerization of ZDMA promoted by zinc methylmercaptobenzimidazole

Improved understanding of in-situ polymerization of zinc dimethacrylate: The solid bulk polymerization

Effect of Curing Systems on Properties of Chlorinated Butyl Rubber/nylon 12 Dynamic Vulcanizates

Strain-induced crystallization of natural rubber/zinc dimethacrylate composites studied using synchrotron X-ray diffraction and molecular simulation

Effect of Interface on Bulk Polymer: Control of Glass Transition Temperature of Rubber

Impact of Curing Temperature on Microstructures and Properties of Isobutylene–isoprene Rubber/clay Nanocomposites

The morphology of zinc dimethacrylate reinforced elastomers investigated by SEM and TEM

Influence of Curing Systems on Properties of HNBR/CR Blend

The Changes of Status of Brominated Phenolic Resin in EPDM During Curing and Its Effects on the Properties

Improved mechanical properties and special reinforcement mechanism of natural rubber reinforced by in situ polymerization of zinc dimethacrylate

Influence of Melamine Formaldehyde Microsphere on the Vulcanization Kinetics and Mechanical Properties of Nitrile Butadiene Rubber

Effect of high-temperature curing on the crosslink structures and dynamic mechanical properties of gum and N330-filled natural rubber vulcanizates

Influence of graphene functionalized with zinc dimethacrylate on the mechanical and thermal properties of natural rubber nanocomposites

Investigation of preparation for reactive halloysite loading ZDMA and its thermo-oxidative resistance on the HNBR/FKM composites

Relationship between structure and damping property of hydrogenated nitrile rubber

Influence of accelerators on structure of sulfur-cured natural rubber by nuclear magnetic resonance spectroscopy