Abstract:Semi-interpenetrating network composites containing 40 vol.% ceramics (5Al2O3·8SiO2) and 60 vol.% Al-alloy were fabricated in place of cast iron available for automotive brake rotors. The friction and wear performances of brake pads dry sliding against the composites were measured using a SRV testing machine. The test procedures include friction fade and recovery, load sensitivity at 100 and 250°C, and wear. The friction was found to increase first and then decrease with increasing temperature, followed by the inverse recovery upon cooling. Wear showed an incremental tendency over a wide temperature range. For loads from 40 to 160 N, the friction decreased at 100 and 250°C. At load below 128 N, the former friction was inferior to the latter while at load above 128 N the friction exhibited an inverse tendency. Wear mildly increased with load at 100 °C and decreased dramatically at 250 °C. SEM and EDS investigations revealed that the worn pad surfaces at 250 °C were covered by more tribofilms, including more coke and graphite with friction-reducing action as well as fewer compounds (corresponding to Si and Al) with friction-increasing action in comparison with those at 100 °C. The compression of the tribofilms contributed to a large decrease in the friction and wear with increasing load. However, at 100 °C E-glass fibers exposed at the worn surfaces inhibited the excessive wear of the pad despite lack of more tribofilms. Their glossy surfaces decreased the friction. The proposed friction models explain some friction and wear behaviour better.

An Experimental Investigation of Semi-Interpenetrating Network Ceramic Skeleton-Reinforced Al-Alloy Composites Dry Sliding Against Cr12 Die Steel

Wear Behaviour and Microstructural Changes of SiCw-Al Composite under Unlubricated Sliding Friction

Tribological behavior of aluminum matrix composites reinforced with ceramic particulates in dry sliding against a semimetallic friction material

Infiltration, Interface Microstructure and the Dry Sliding Wear Behavior of Network Ceramics/Fe-Alloy Composites

Friction and Wear Behaviour of Brake Pads Dry Sliding Against Semi-Interpenetrating Network Ceramics/Al-alloy Composites

Research On Wear Behavior Of Atc Cermet Material

Tribological Behavior of In-Situ (cr, Mo)/Fe3al-20 Wt.%Al2o3 Composites at Elevated Temperatures

Microstructure, Mechanical and Tribological Properties of Al0.3CrFeNiTi0.3-CaF2/BaF2 Self-Lubricating Composite Fabricated by Spark Plasma Sintering

Dry Sliding Wear of a Ti50Ni25Cu25 Particulate-Reinforced Aluminum Matrix Composite

The Tribological Behavior of Aluminum-matrix Composites Reinforced with Ceramic Particulates in Dry Sliding Against a Semi Metallic Frictional Material

Tribological Characterization of an Alumina-Based Composite in Dry Sliding Contact Against Laser-Heated and Unheated Inconel 718

Tribological Behavior of Short Carbon Fiber or Hybrid with SiCp Reinforced Al Alloy Composites

Dry Friction and Wear Performance of SiC 3D Continuous Ceramic Frame Reinforced 7075al Alloy

Dry Sliding Wear Behavior of Al2O3 Fiber and SiC Particle Reinforced Aluminium Based MMCs Fabricated by Squeeze Casting Method

Two-body Abrasive Behavior of Brake Pad Dry Sliding Against Interpenetrating Network Ceramics/al-Alloy Composites

Preparation and Friction Properties of SiC-Al2O3/2A50 Co-Continuous Composites

Tribological Properties and Wear Mechanisms of the Couple of 3D Needled C/SiC Composite and 30CrSiMoVA

Tribological Properties of in Situ Fe3al-20 Wt% Al2o3 Composites

Tribological behavior of NiCrW-based self-lubricating composites against IC10 alloy under high temperature and extremely slow sliding speed

Tribological Behaviour of Al18B4O33-whisker-reinforced Hypoeutectic Al–Si–Mg-matrix Composites under Dry Sliding Conditions

Friction and Wear Properties of Fe Matrix Composites Reinforced with 3D-Meshy Al_2O_3