Abstract:The Journal of Strain Analysis for Engineering Design, Ahead of Print. In the present work, the process chain in tube production by roll forming of the steel 34MnB5 was examined in more detail. The process chain consisting of the steps (i) roll forming, (ii) HFI welding, and then (iii) straightening and final calibration was mapped using the finite element method. In addition to the pipe geometry, the residual stress distribution was considered as an essential target value for the assessment of the performance of the tubes under service conditions. The objective of the project is to describe the manufacturing process and thus the processing induced residual stress distributions as realistically as possible. For a more detailed characterization of the process and above all for the validation of the numerical simulations, experimental residual stress analyses were carried out for the final state of the tubes using complementary analysis methods. The contour method was used to determine the 2D-distribution of residual stresses across the transverse and longitudinal sections of the manufactured pipes. These measurements were supplemented by local residual stress analyses using the incremental hole drilling method and X-ray residual stress analyses. The work thus pursues both a methodical approach to the analysis of the internal stresses induced by the process using complementary methods and also a manufacturing approach to the analysis and evaluation of the production chain. In particular for the axial components of the residual stresses, it can be shown that experimentally determined residual stresses correlate well with the numerically calculated values. The contour method is excellently suited to monitor the uneven distribution of the internal stresses over the pipe cross-section. The results of the simulation show that the overall residual stress distribution that is determined using the contour method mainly results from the plastic strains introduced by the roll forming process. X-ray and hole drilling analyses are shown to be more suitable for measuring locally present residual stresses at defined positions on the outer tube surface. In this way it can be shown that the simulation approach described provides an accurate model of the process.

Numerical and experimental study on seam welding behavior in extrusion of micro-channel Tube

Die Design and Finite Element Analysis of Welding Seams during Aluminum Alloy Tube Extrusion

Integrated Physical and Numerical Simulations of Weld Seam Formation During Extrusion of Magnesium Alloy

Physical Simulation Method for the Investigation of Weld Seam Formation During the Extrusion of Aluminum Alloys

Numerical and Experimental Studies on the Improvement of Gas Chamber Structure During Gas-Assisted Extrusion

Influence of extrusion method on the microstructure and mechanical properties of formed magnesium alloy tubes

Analysis of the Bonding Strength and Microstructure of AA6082 Extrusion Weld Seams Formed During Physical Simulation

Numerical and experimental analysis of the isothermal high temperature pneumoforming process

Numerical Simulation and Process Optimization of Internal Thread Cold Extrusion Process

Combined Effect of Tungsten Inert Gas Welding and Roller Expansion Processes on Mechanical and Metallurgical Characteristics of Heat Exchanger Tube-To-Tubesheet Joints

Study on the Melt Rheological Characterization of Micro-Tube Gas-Assisted Extrusion Based on the Cross-Scale Viscoelastic Model

Basic Study on Thixo-Co-Extrusion of Multi-Layer Tube with Al/Mg Alloys

Development and Strength Evaluation of Ring Projection Welding Process of the Microminiature Tube and Tubesheet

Experimental and numerical analysis of residual stresses induced by the manufacturing process of longitudinal welded tubes

Numerical Simulation and Microstructure Analysis of 30CrMnMoRe High-Strength Steel Welding

Numerical Investigation on Molten Pool Dynamics and Defect Formation in Electron Beam Welding of Aluminum Alloy

Numerical Simulation of Tube-Plate Welding Structure with T-Shaped Sections

Thermo-Fluid-Coupled Analysis of Double Fillet Welds on Tube Membrane Panels During Submerged Arc Welding

Numerical Simulation of Tube Manufacturing Consisting of Roll Forming and High-Frequency Induction Welding

Effect of Tube Arrangement on the Welding of the Tube-to-Tubesheet Joint of Shell-and-Tube Heat Exchangers Using the Finite Element Method

Three-dimensional numerical study of heat-affected zone in induction welding of tubes