Abstract:reducing atmosphere. [3] It has been observed that one of the major causes to low performance of solid oxide fuel cell is its impedance, especially, from electrochemical reaction occurring at the electrode. Usually, carbon material is used to form pores in the electrode for gas diffusion, which is mixed with electrode material, and thermally treated at about 800 oC, then eliminated to make pores. The reaction between carbon material and electrode materials may occur due to the high temperature treatment. In this study, we adopted sublimation material to form pores which can be eliminated at low temperature enough to avoid the reaction with electrode material. The cell performance was investigated. Experimental BaLaIn2O5.5 (BLI) powder was synthesized by a solid state reaction of barium carbonate, indium oxide, and lanthanum oxide. The BLI powder was shaped into pelletlike, pressed under 392 Mpa and sintered at 1400oC for 10 h. The 11 mm diameter BLI electrolyte pellet was polished to a thickness of 0.5 mm. (La0.75Sr0.25)0.9Cr0.5Mn0.5O0.3 (LSCM) mixed with 5wt% NiO and Sm0.5Sr0.5CoO3 (SSC) were employed as anode and cathode, respectively. In this study, anthraquinone, barbituric acid, and L-valine were selected as pore former materials due to their sublimation property. Each material was mixed into both LSCM and SSC with different compositions at 10, 15, 20 and 30 wt%. The mixture was then painted on anode and cathode face of BLI electrolyte pellets. The painted pellets were treated at 200°C, far below the sintering temperature, for sublimation of the pore former and then pores were created in the electrodes. Subsequently, the pellets were heated at 1000-1200°C. The power generation tests at 800°C were carried out to examine the cell performance. A mixture of methane and air was supplied with 1:4 volume ratios.

Submicron Γ-Lialo2 Powder Synthesized from Boehmite

Preparation of LiAlO2 Powders for the Electrolyte Matrix Material

The Optimization of Matrix Preparation Process and Performance Testing for Molten Carbonate Fuel Cell

Preparation and Properties of LSGM (Li/Na)(2)CO3 Composite Electrolytes for LT SOFC

Validating the efficiency of γ-Al2O3/La0.6Sr0.4Co0.2Fe0.8O3-δ double-layer electrolyte for low temperature solid oxide fuel cell

Preparation of LiMO2 (M = Co, Ni) cathode materials for intermediate temperature fuel cells by sol-gel processes

Electrolyte Single Chamber Solid Oxide Fuel Cell by Using Sublimation Materials As Pore Former in Electrode Preparation

Research on the Synthesis and Reaction Mechanism of Sub-Micron Lialo2 Powders

Co-synthesis of LSCFN-GDC Electrode for Symmetric Solid Oxide Fuel Cell Running on Propane

Preparation and Performance of Anode-supported LaGaO<SUB>3</SUB>-based Electrolyte Solid Oxide Fuel Cells with Sm-doped CeO<SUB>2</SUB> Buffer Layers

Preparation and Corrosion Resistance of Β-Al2o3-mgal2o4 Multiphase Materials for Synthesising Li-ion Battery Cathode Materials

In-situ synthesis of LSCF-GDC composite cathode materials for Solid Oxide Fuel Cells

Nanostructured Lscf-GDC Cathodes Via a Sol–Gel Method for High Performance Solid Oxide Fuel Cells

Preparation and Performance of Large-Area La0.9Sr0.1Ga0.8Mg0.2O3−δ Electrolyte for Intermediate Temperature Solid Oxide Fuel Cell

LSCF Nanopowder from Cellulose–Glycine-Nitrate Process and its Application in Intermediate-Temperature Solid-Oxide Fuel Cells

Coupling behavior between lattice dynamics and Li self-diffusion in layered α-LiAlO2 ceramic

Large-scale Synthesis of Lithium- and Manganese-Rich Materials with Uniform Thin-Film Al 2 O 3 Coating for Stable Cathode Cycling

Combustion Synthesis of Γ-Lithium Aluminate by Using Various Fuels

PVA-assisted Synthesis and Characterization of Nano-Crystalline La 3+ and Mg 2+ Co-Doped CeO 2 Electrolyte for Intermediate-Temperature Solid Oxide Fuel Cells

Ce0.8Sm0.2O2-α ceramic prepared by sol-gel method at low temperature and its composite electrolyte in intermediate temperature fuel cells

Interface Control Strategy of Synthesis LiMn2O4@Al2O3 Assisted by Tert-Butanol