Abstract:A n-butanol/diesel spray test system was constructed to conduct common rail bench test and constant volume bomb experiments in present work to investigate the impact of different n-butanol blending ratios on spray characteristics and the spray evolution process. To be specific, the research was carried out under the n-butanol blending ratios ofwith 0, 10%, 20%and 40% respectively to study various n-butanol blending ratio effects and to analyze the variation of the physical and chemical characteristics of the fuel. Then, the fuel spray patterns data at 0.4 ms was carefully collected and analyzed to compar the effect of different n-butanol blending ratios on spray penetration and spray angle. In addition, an-butanol/diesel spray model in engine cylinder was also established, to analyze how spray penetration and SMD of blended fuel varied during spray process, , as well as the impacts of n-butanol blending ratios on evaporation characteristics of blended fuel. Furthermore the various changes in velocity field and number density field in spray processes with different blending ratios have been taken into consideration and discussed for more detailed problems. It can be observed from the research data that: in normal temperature and pressure region,as the n-butanol blending ratio increased,the spray penetration decreased and there was a moderate rise in spray angle during spray process; as blending ratios of n-butanol increased by 40%, the spray penetration slightly reduced by 4.95%while reversely the spray angle climbed by 16.7%. Also when the injection pressure ascended, there was obvious rise both in the spray penetration and spray angle, particularly, if injection pressure rose by 40 MPa , the spray angle increased by 28.43°. During the spray evolution process, the n-butanol blending ratios influenced the spray penetration slightly, while in the very initial step of fuel blending process, the higher the n-butanol blending ratio was, the smaller SMD of blended fuel became. Along with the development of the spray process, however, the ultimate spray penetrations of different blended fuel were basically the same. In the injecting duration period, with the increasing of n-butanol blending ratio, there was a substantial drop in the mass of the fuel injected into the cylinder, and the peak velocity value of the jet dropped distinctly. Moreover, as a result of the fall in the viscosity and surface tension, the volatilization of blended fuel was apparently enhanced and subsequently fuel evaporation mass was increased slightly. The n-butanol blending ratios had quite limited impact on number density of drops but obviously facilitated the spray period, that is, the larger the blend ratio was, the better the spray characteristics would be. Besides this, in the central region of the downstream jet the figure of number density reached the highest.

Spray, ignition and combustion characteristics of biodiesel and diesel fuels injected by micro-hole nozzle under ultra-high injection pressure

Numerical Investigation of Diesel Spray Combustion Characteristics in the Ammonia/air Atmosphere

Experimental Analysis in Dynamics Characteristics of Impinging Spray by a PFI Injector : from Spray Atomization to Fuel Adhesion Formation

Study on injection characteristics of diesel and DME

Experimental Research on Spray,Ignition and Combustion Characteristics of Biodiesel Blend

Spray behavior of butanol-diesel and numerical simulation of mixture formation with engine

Role of injection pressure on fuel atomization and spray penetration on the Thevetia peruviana and Jatropha curcas biodiesel blends with nanoparticle

Study on spray characteristics of biodiesel alternative fuels for in-cylinder environment of diesel engine

Effects of fuel injection pressure and quantity on low octane gasoline sprays in a simulated high-pressure ambient environment of a gasoline compression ignition engine

Numerical analysis of spray characterization of blends of hydrous ethanol with diesel and biodiesel

Assessing fuel properties effects of 2,5-dimethylfuran on microscopic and macroscopic characteristics of oxygenated fuel/diesel blends spray

Experimental Investigation on the Macroscopic and Microscopic Spray Characteristics of Dieseline Fuel

Effects of nozzle hole size and rail pressure on diesel spray and mixture characteristics under similar injection rate profile – experimental, computational and analytical studies under non-evaporating spray condition

Experimental Study on the Spray Characteristics of an Oxygenated Blends

Investigation on the Spray Characteristics of DMF- Isooctane Blends Using PDPA

Impact of injection pressures on properties, microscopic behavior, and microexplosions in biodiesel-emulsified fuel with biosurfactant

Spray Characteristics of a Gasoline-Diesel Blend (ULG75) Using High-Speed Imaging Techniques

Characterization of diesel spray with novel high-speed laser absorption scattering technique under diesel engine-like condition

Experimental research on the effects of kerosene on the pre-injection spray characteristics and engine performance of dual-direct injection diesel Jet Controlled Compression Ignition mode

An Optical Study on Liquid-Phase Penetration, Flame Lift-off Location and Soot Volume Fraction Distribution of Gasoline–diesel Blends in a Constant Volume Vessel

Microscopic Imaging on Diesel Spray and Atomization Process