Abstract:In the injection over‐molding process, short carbon fiber reinforced polyether‐ether‐ketone was injected onto the surface of woven carbon fiber reinforced PEEK laminate substrate. The interface between the two materials was formed by different bonding modes, such as mechanical interlocking, matrix entanglement and crystallization. In this paper, the effects of mold temperature and melt temperature on the different bonding modes and interfacial performance were investigated. A weak interface is formed between injected plastic and substrate during the injection over‐molding process. This study investigated the effects of mold temperature and melt temperature on the bond strength of injection over‐molded components, which were produced by injecting short carbon fiber reinforced polyether‐ether‐ketone (SCF/PEEK) onto the surface of woven carbon fiber reinforced PEEK (WCF/PEEK) laminate substrate. The results show that the interfacial laminar shear strength (ILSS) increases significantly from 15.8 to 50.0 MPa as the mold temperature raises from 190 to 260°C. The ILSS increases first and then decreases with melt temperature raises from 380 to 420°C, achieving a maximum value of 44.4 MPa at 410°C melt temperature. Crystallinity analysis and microscopic observations indicate different bonding modes are formed at the interface. The matrix tangling appears in the matrix enrichment area, interlocking, and tangling appear in the pits and weak tangling and cracks occur on the fiber surface. The mold temperature affects the ILSS by changing the crystallization property and the connection mode in the interface, while the melt temperature affects the ILSS by changing the area of the matrix entanglement. The relationship between the process conditions—interfacial microstructure—interfacial mechanical performance was discussed.

The Effect of Heat Treatment on Mechanical Properties of Car Interior Fabric Used for Injection Molding

Simulation of the Effects of Structural Parameters of Glass Fiber Fabric on the Thermal Insulation Property

Influences of Structural Parameters on the Thermal Properties of Coated Glass Fiber Fabrics under Ablation Condition Investigated by Numerical Model

Effect of heat treatment on the mechanical properties of PBT/PET yarn

Study on the effect of the molding process and service temperature on the mechanical properties and low‐velocity impact performance of the ultra‐high molecular weight polyethylene fiber laminates

A Review on the Effect of Heat Treatment for Thermoplastic Composites

Investigation of tensile behavior and molecular structure of the thermoplastic polyurethane sheets injection molded at different mold temperatures

INFLUENCE OF HEAT-TREATMENT ON MECHANICAL PROPERTY OF GLASS FIBER REINFORCED POLY(ETHYLENE TEREPHTHALATE)

A multiscale study of heat treatment effects on the interlayer mechanical properties of 3D printed continuous carbon fiber‐reinforced composites

The temperature effect on the inter-laminar shear properties and failure mechanism of 3D orthogonal woven composites

Effects of high temperature and strain rate on the impact-induced inter-laminar shear behavior of plain woven CF/PEEK thermoplastic composites

Effect of Hot-Pressing Process on Mechanical Properties of UHMWPE Fiber Non-Woven Fabrics

Effect of heat treatment and test temperature on transverse cracking in tensile loading

Effects of Thermoforming Parameters on Woven Carbon Fiber Thermoplastic Composites

Effect of isothermal heat treatment on crystallinity, tensile strength and failure mode of CF/PPS laminate

High-Temperature Effect on the Tensile Mechanical Properties of Unidirectional Carbon Fiber-Reinforced Polymer Plates

Study of Heat Treatment Effect on Mechanical Properties of Epoxy Resin Reinforced with Fiber Glass

Effects of Heat Treatments on Puncture Resistant Properties of Polyamine and Polyamide-based Nonwoven Fabrics

Thermal Treatment Effects on Structure and Mechanical Properties of Polybutylene Terephthalate and Epoxy Resin Composites Reinforced with Glass Fiber

Transverse impacts‐induced deformation and damage of 3D angle‐interlock woven composites at elevated temperatures

Bond strength and bond mechanism of injection over‐molded woven carbon fiber/PEEK‐short carbon fiber/PEEK composite components