Abstract:Abstract The in-situ formation of oxides on alloy surface induced by high temperature can effectively reduce wear and resist oxidation. In consideration of the solid solution strengthening effect and great oxidation resistance of additional elements at elevated temperature, the NiCrWMoCuCBFe coating was prepared by high velocity oxygen flame (HVOF) spraying technology, and its tribological behavior was scrutinized from 25 to 800 °C. By means of high temperature Vickers hardness tester and high temperature X-ray diffractometer, the mechanical properties and microstructures of NiCrWMoCuCBFe coating were measured. And the effect of the mechanical properties and microstructures of the coating on tribological performance was discussed in detail. The results showed both its friction coefficient (0.37) and wear rate (5.067 × 10 −6 mm 3 ·N −1 ·m −1 ) at 800 °C were the lowest, which was mainly related to the formation of “glaze” layer on the coating surface at high temperature. The glaze layer consisted of two parts, which were NiCr 2 O 4 oxide film with the ability of interlaminar slip formed in the outer layer and nano-grains existed in the inner layer. Worth mentioning, these nano-grains provided bearing capability while the oxide film was vital to reduce wear rate and friction coefficient. As the ambient temperature increased, many hard oxides were produced on the wear scars, including NiO, Cr 2 O 3 , MoO 3 , and Mo 2 C. They can improve tribological and mechanical properties of NiCrWMoCuCBFe coating at a wide temperature range.

Performance of HVOF NiCr cermets coating against high temperature sulfur corrosion and erosion

High-Temperature Erosion of HVOF Sprayed Cr 3 C 2 -NiCr Coating and Mild Steel for Boiler Tubes

Comparing Study of High Temperature Erosion of HVOF Sprayed Cr3C2-NiCr Coating and Mild Steel for Boiler Tube

Resistance of HVOF-Sprayed Cr3C2-25NiCr and WC-10CO-4Cr coatings to cavitation and erosion by mud jetting

Preparation and High Temperature Erosion Resistance of Cr3C2-NiCr Coating

Effect of vacuum heat treatment on microstructure and corrosion behavior of HVOF sprayed AlCoCrFeNiCu high entropy alloy coatings

Comparison on multi-angle erosion behavior and mechanism of Cr3C2-NiCr coatings sprayed by SPS and HVOF

Microstructure and Corrosive Wear Properties of CoCrFeNiMn High-Entropy Alloy Coatings

Corrosive wear behavior of HVOF-sprayed micro-nano-structured Cr3C2–NiCr cermet coatings under aqueous media

Abrasive Wear Resistance of HVOF Deposited Cr3C2-NiCr Coatings

Fabrication and Characterization of HVOF Sprayed CoNiCrAlY-6%Al2O3 Coating to Improve High-Temperature Oxidation Resistance

Performance evaluation of HVOF sprayed WC-10Co4Cr coatings under slurry erosion

Erosion Performance of HVOF-Sprayed Cr 3 C 2 -Nicr Coatings

An HVOF-Sprayed (Cr3C2-NiCr+Co) Composite Coating on Ductile Cast Iron: Microstructure, Mechanical Properties, and Scratch Resistance

High Temperature Corrosion Resistance of High Velocity Oxy-Fuel Sprayed Ni-Based Composite Coating

Microstructural Characterization and Abrasive Wear Performance of HVOF Sprayed Cr3C2–NiCr Coating

High Temperature Oxidation and Tribological Behavior of Cr3C2-25CoNiCrAlY and Cr3C2-25NiCr Coatings Prepared by AC-HVAF

Addressing challenges in high-temperature oxidation of ultra-supercritical boiler tubes via FeCoNiCrMo high-entropy alloy coatings

High temperature induced “glaze” layer formed in HVOF-sprayed NiCrWMoCuCBFe coating and its wear reduction mechanism

Cyclic Oxidation Behavior of HVOF Thermally Sprayed WC Cermet Based on AISI 1045 Steel

Hydro-abrasive Erosion and Cavitation-Silt Erosion Characteristics of HVOF Sprayed WC-Ni Cermet Coatings under Different Flow Velocities and Sand Concentrations