Abstract:{1011}-{1012} double twin is the most common twin type being observed in the rolled AZ31 magnesium alloy, especially at low or moderate rolling temperature. Four types of rolled AZ31 magnesium alloy sheets were produced by rolling strong basal textured AZ31 plates at 150°C and 300°C respectively through different rolling paths by two passes till total reduction 17%. The rolling paths are normal and cross rolling respectively: the rolling directions of the two passes for normal rolling are mentally paralleled while perpendicular to each other for the cross rolling. Sheets are characterized in terms of microstructure and texture using optical microscope and scanning-electron microscope equipped with EBSD detector, and their mechanical performances are measured by uniaxial tensile tests at room temperature and a strain rate of 0.001 s -1. Tensile samples are cut parallel or perpendicular to the final rolling direction to obtain the mechanical anisotropies. The effects of the {1011}-{1012} double twins occurred during rolling on the microstructure, texture and mechanical properties of the rolled sheets are discussed and related to each other. The results show that the fraction of {1011}-{1012} double twins varies widely in different rolled sheets, which are determined by the rolling temperature. The twins in different rolled sheets are arranged in different ways. In the normal rolled sheets, the traces of twins are approximately perpendicular to the final rolling direction, while in the cross rolled sheets there are both traces of twins parallel and to the final directions. This phenomenon is related to the variant selection of twinning during rolling deformation. And the variant selection law is related to the rolling direction. For the same reason, the textures of twins in the rolled sheets produced through different paths are different. The textures of twins will add onto the bulks, and increases the textural difference between the bulks. The differences between mechanical properties of the rolled sheets are also related to the different textures and microstructures of the sheets caused by twins. © Right.

Effect of twinning on Moderate-Temperature Deformation Behavior of hot-roiled Mg Alloy

Effect of twinning on flow stress and hardening during hot compression of twin roll cast Mg alloy

EFFECT OF TWINNING ON MECHANICAL PROPERTY AND WORKABILITY OF Mg ALLOY

Twinning Effects on the Hot Deformation Behavior of AZ31 Mg Alloy

INFLUENCE OF ROLLING TEMPERATURE ON THE {1011}-{1012} TWINNING IN ROLLED AZ31 MAGNESIUM ALLOY SHEETS

Dynamic recrystallization and twinning behavior of magnesium alloy during hot tension

Warm Deformation Behavior of Hot-Rolled Az31 Mg Alloy

The effect of {10¯11}–{10¯12} double twinning on the microstructure, texture and mechanical properties of az31 magnesium alloy sheet during rolling deformation

Twinning and dynamic recrystallization behaviors during inchoate deformation of pre-twinned AZ31 Mg alloy sheet at elevated temperatures

Effect of deformation conditions on twinning of AZ31 magnesium alloy during compression test

Twinning Deformation and Yield Asymmetry Improvement of Magnesium Alloys by Free-End Torsion

Effect of pre-deformation on the activation stress of {10–12} twinning in Mg–3Al–1Zn alloy

The effect of {1011}-{1012} double twinning on the microstructure, texture and mechanical properties of AZ31 magnesium alloy sheet during rolling deformation

Effect of twinning on the deformation behavior of an extruded Mg-Zn-Zr alloy during hot compression testing

Influence of tensile twinning on electrochemical and corrosion behavior of Mg alloy

Twinning Behavior of a Strongly Basal Textured AZ31 Mg Alloy During Warm Rolling

Dynamic recrystallization, twinning behaviors and mechanical response of pre-twinned AZ31 Mg alloy sheet along various strain paths at warm temperature

Effect of High-Temperature Deformation Twinning on the Work Hardening Behavior of Fe-38Mn Alloy during Hot Shear-Compression Deformation

Microstructure, Texture and Mechanical Properties Evolution of Pre-Twinning Mg Alloys Sheets During Large Strain Hot Rolling

Effects of Micro-Twin Lamellar Structure on the Mechanical Properties and Fracture Morphology of AZ31 Mg Alloy

Effect of Twinning on Flow Stress During Initial Stage of Hot Compression of Twin Roll Cast Mg-5.51Zn-0.49Zr Alloy