Abstract:This study delves into the influence of laser welding parameters on the microstructural evolution, surface roughness, and hardness of dissimilar lap joints formed by welding 340BH steel (upper) to cold-rolled pure vanadium (bottom) in an attempt to successfully develop metal membranes by adopting a novel technological route. Specifically, we examined power levels of 0.3 kW and 0.4 kW combined with varying welding speeds (40 mm/s, 50 mm/s, and 60 mm/s). The results indicate that defect-free joints were achievable at the higher welding speed of 60 mm/s. This conclusion is supported by the observed surface roughness profile. Elemental interdiffusion and temperature play pivotal roles in the formation of these dissimilar joints. These factors determine the dimensions of the heat-affected zone (HAZ) and the fusion zone (FZ) under all welding conditions. Notably, the high cooling rates during laser welding hindered the formation of intermetallic phases both in the FZ and at the interface between the metals. Microstructural examination of the HAZ/FZ on the Fe side showed a coarser microstructure when using a power of 0.4 kW, in contrast to the lath martensite observed at 0.3 kW. These observations align with the cooling curve derived from finite element analysis (FEA). FEA was also used to estimate temperature profiles throughout the welded area, and the results were consistent with experimental data. Further microstructural analysis using electron backscattered diffraction (EBSD) revealed a significant phenomenon: the formation of recrystallized grains of vanadium in the HAZ near the FZ on the vanadium side. Microhardness tests, conducted to gauge joint quality, displayed varying hardness levels across the base metal (BM), HAZ, and FZ interfaces. At a power of 0.3 kW, the HAZ displayed greater hardness than the FZ and BM due to the formation of lath martensite. Conversely, at a power setting of 0.4 kW, a reduction in hardness was observed within the HAZ, attributable to coarser ferrite formation.

Crossed-Wire Laser Microwelding of Pt-10 Pct Ir to 316 LVM Stainless Steel: Part II. Effect of Orientation on Joining Mechanism

Crossed-Wire Laser Microwelding of Pt-10 Pct Ir to 316 Low-Carbon Vacuum Melted Stainless Steel: Part I. Mechanism of Joint Formation

Laser spot microwelding of crossed Pt/Ir alloy wire to 316 LVM stainless steel wire

Dissimilar Laser Welding of Austenitic Stainless Steel and Abrasion-Resistant Steel: Microstructural Evolution and Mechanical Properties Enhanced by Post-Weld Heat Treatment

Effect of welding parameters on weld surface roughness, hardness, and microstructure in laser-welded 340BH-steel and pure vanadium

Microstructure and Mechanical Properties of Pulsed Laser Welded Al/steel Dissimilar Joint

A Comparable Study on Laser Welding Behaviors of Selective Laser Melted 304 Stainless Steel, Inconel 718 Superalloy and Ti-6Al-4V Alloy

Impact of microstructure evolution on the corrosion behaviour of the Ti–6Al–4V alloy welded joint using high-frequency pulse wave laser

Investigation on electron beam welding of dissimilar wrought/selective laser melting AISI 304 stainless steel plates

Inhomogeneity of microstructure and mechanical properties in the interlayer regions for narrow gap laser wire filling welding of 316L stainless steel

Microstructure and Tensile Behavior of Laser Arc Hybrid Welded Dissimilar Al and Ti Alloys

Hybrid Resistance-Laser Spot Welding of Aluminum to Steel Dissimilar Materials: Microstructure and Mechanical Properties

Effects of interlaminar microstructural inhomogeneity on mechanical properties and corrosion resistance of multi-layer fiber laser welded high strength low alloy steel

Interfacial microstructure evolution and mechanical properties in laser welded Invar alloy/TC4 dissimilar joints

Effect of Welding Parameters on Mechanical Performance and Microstructural Characterization of Fiber Laser Oscillation Welded Dissimilar TWIP/304L Steel Joints

Microstructure Evolution and Mechanical Properties of Laser Welded Dissimilar/Similar Joints Between Medium‐Mn Transformation‐Induced Plasticity Steel and DP980/22MnB5 Steels

Study on Microstructure and Properties of Laser Dissimilar Welded Joints of Ultra-High Strength PHS1500/PHS2000 Steel

Laser and hybrid laser welding of type 316L(N) austenitic stainless steel plates

Study on microstructures and mechanical performance of laser transmission welding of poly-ether-ether-ketone (PEEK) and carbon fiber reinforced PEEK (CFR-PEEK)

Microstructure evolution and mechanical properties in the depth direction of ultra-high power laser-arc hybrid weld joint of 316L stainless steel

Tensile resistance, microstructures of intermetallic compounds, and fracture modes of welded steel/aluminum joints produced using laser lap welding