Abstract:Using granulated blast furnace slag (GGBS) as the volcanic ash material and fly ash (FA) as the supplementary material, the study was conducted to investigate the mix proportions of an alkali-activated solid waste cementitious material under the stimulating effect of alkali activator carbide slag (CS). This type of cementitious material could serve as a substitute for a portion of cement usage, contributing to resource conservation and mitigating environmental pollution caused by solid waste. This facilitates green and sustainable development. Firstly, an analysis of three raw materials was conducted, and the mix proportions were designed with reference to the CaO-Al 2 O 3 -SiO 2 system of Portland cement. Then 28 groups of specimens were prepared based on the designed mix proportions. The flowability and setting time of each group of specimens were tested. It was observed that an increase in the amount of CS and a decrease in the amount of GGBS resulted in decreased flowability and earlier setting times of the specimens. Additionally, FA exhibited a retarding effect on setting time. Compressive strength tests were conducted on these specimens, revealing that the optimal CS content ranged between 20 % and 40 %. Overall, FA had minimal impact on compressive strength, but it contributed to increased compressive strength in the specimens at later ages. Subsequently, microscopic characterization of the hydration products was performed using X-ray Diffraction (XRD), Fourier Transform Infrared (FTIR), Differential Thermal Analysis (DTA), Scanning Electron Microscope (SEM), and Energy Dispersive Spectrometer (EDS). The hydration products were identified as predominantly composed of calcium silicate hydrate. The quality and defects in the microstructure of gel products from various specimen formulations were compared to elucidate differences in macroscopic performance. Finally, the hydration process mechanism diagram of alkali-activated materials was presented to illustrate the stimulation and formation of gel products, primarily composed of C-S-H. This diagram revealed the principles behind the action of alkali-activated cementitious materials. The proposed design and testing methodology for the GGBS-FA-CS system in this study had certain reference significance for research in the direction of alkali-activated solid waste cementitious materials.

Preparation and Characterization of Calcium Silicate Slag Based Lightweight Wall Materials

Understanding the Role of Calcium Silicate Slag in Sodium Carbonate-Activated Green Materials: Influence on Kinetics, Strength, and Efflorescence

Preparation of Fly Ash-based Lightweight Loadbearing Wall Materials: an Experimental Study

Hydration Characteristics and Environmental Friendly Performance of a Cementitious Material Composed of Calcium Silicate Slag.

Preparation of High Strength and Lightweight Wall Materials Using Oil Shale Ash As Raw Materials

Hydrothermal synthesis and characterization of alkali-activated slag-fly ash-metakaolin cementitious materials

A Study on the Hydrothermal Synthesis of Calcium Silicate Products by Calcination of Full-Component Waste Concrete

Preparation of autoclaved wall materials from oil shale ash

The preparation and formation mechanism of ferrochrome slag-based high-strength ceramic aggregate and its impact on the performance of concrete

Recycling of Silicomanganese Slag and Fly Ash for Preparation of Environment-Friendly Foamed Ceramics

Study on the preparation, performance, and mechanism for solid waste cementitious materials

PREPARATION OF LIGHTWEIGHT WALL MATERIALS BASED ON INFLATED PEARLITE FROM COLLOIDAL ALUMINOSILICATE WASTE RESIDUE

The Technical Study on the Preparation of Lightweight Ceramsite Made from Sewage Sludge and Fly Ash

Preparation and properties of silicate inorganic exterior wall insulation based on thermal energy storage

Reuse of the soda sludge dealt with water washing as a supplementary material for the synthesis of clinker binders

Hydration Mechanisms of Alkali-Activated Cementitious Materials with Ternary Solid Waste Composition

SYNTHESIS AND CHARACTERIZATION OF HIGH BELITE SULFOALUMINATE CEMENT THROUGH RICH ALUMINA FLY ASH AND DESULFURIZATION GYPSUM

Study on the Recycling of Ceramic Polishing Slag in Autoclaved Aerated Foam Concrete by Response Surface Methodology

High performance C-A-S-H seeds from fly ash-carbide slag for activating lithium slag towards a low carbon binder

Hydration characteristics of silica-alumina based cementitious materials composed of steel slag

Utilizing Ceramic Waste for Autoclaved Aerated Concrete