Abstract:Titanium and its alloys form a thin amorphous protective surface oxide when exposed to an oxygen environment. The properties of this oxide layer are thought to be responsible for titanium and its alloys biocompatibility, chemical inertness, and corrosion resistance. Surface oxide crystallinity and pore size are regarded to be two of the more important properties in establishing successful osseointegration. Anodization is an electrochemical method of surface modification used for colorization marking and improved bioactivity on orthopedic and dental titanium implants. Research on titanium anodization using sulphuric acid has been reported in the literature as being primarily conducted in molarity levels 3 M and less using either galvanostatic or potentiostatic methods. A wide range of pore diameters ranging from a few nanometers up to 10 μm have been shown to form in sulfuric acid electrolytes using the potentiostatic and galvanostatic methods. Nano sized pores have been shown to be beneficial for bone cell attachment and proliferation. The purpose of the present research was to investigate oxide crystallinity and pore formation during titanium anodization using a pulsed DC waveform in a series of sulfuric acid electrolytes ranging from 0.5 to 12 M. Anodizing titanium in increasing sulfuric acid molarities showed a trend of increasing transformations of the amorphous natural forming oxide to the crystalline phases of anatase and rutile. The pulsed DC waveform was shown to produce pores with a size range from ≤0.01 to 1 μm(2). The pore size distributions produced may be beneficial for bone cell attachment and proliferation.

Formation and Crystallization Characteristics of Anodic Oxide Film on Pure Titanium in Potentiostatic Mode

Formation and Crystallization of Anodic Oxide Films on Sputter-Deposited Titanium in Potentiostatic and Potential-Sweep Modes

Effect of Oxidation Time on the Structure and Properties of Ti-25Nb-3Zr-2Sn-3Mo Titanium Alloy Microarc Oxide Film Layer

Growth and Crystallization of Titanium Oxide Films at Different Anodization Modes

Time Dependence of Growth and Crystallization of Anodic Titanium Oxide Films in Potentiostatic Mode

Growth and Crystallization of Anodic Titanium Oxide Films

Crystallization of the Anodic Oxide on Titanium in Sulphuric Acids Solution at a Very Low Potential

Effect of Anodic Oxidation Parameters on Crystallization Behavior of TiO2 Films

Formation of crystalline TiO_2 by anodic oxidation of titanium

Growth and crystallization behaviors of anodic oxide films on sputter-deposited titanium at very low potentials

The Effect of Potential on Surface Characteristic and Corrosion Resistance of Anodic Oxide Film Formed on Commercial Pure Titanium at the Potentiodynamic-Aging Mode

Effect of Accumulation of Ti4+ in 0.1 M H2SO4 Electrolyte on Growth and Crystallization of Anodic Titanium Oxide Films

Preparation of TiO2 Porous Films on Pure Titanium Surface

Formation of Porous Anodic Oxide Film on Titanium in Phosphoric Acid Electrolyte

Electrochemical Characteristics of the Anodized Titanium Oxide Films in Sulfuric Acid

Growth behaviour of anodic oxide film on titanium alloy

Optimization and Characterization of Anatase Formed on Anodized Titanium in Sulfuric Acid

Effect of Anodization Time on Morphology and Electrochemical Impedance of Andic Oxide Films on Titanium Alloy in Tartrate Solution

A Study of Titanium Oxide Film Electrodes Prepared by Direct Thermal Oxidation Ⅰ. Preparation, Structure and Electrochemical Properties

Formation, Microstructures and Crystallization of Anodic Titanium Oxide Tubular Arrays

Nanopore formation on the surface oxide of commercially pure titanium grade 4 using a pulsed anodization method in sulfuric acid