Abstract:Direct solvent extraction (DSX) was applied to produce purified concentrated Ni and Co solutions from a synthetic sulfuric liquor containing Ca, Cu, Mg, Mn, and Zn as impurities, which simulates the solution obtained by the sulfation-roasting-leaching process after precipitation of Fe, Al, and Cr. The commercial extractants Versatic 10, Cyanex 272, D2EHPA, TBP were used in 3 solvent extraction circuits. In the first circuit, operated at 40 °C, Versatic 10 (0.5 M) fully extracted Cu, Zn, Ni, and Co in 3 stages at O/A = 2:1, and pH 6.5, leaving remaining Mn (54% was extracted) and most of the Ca and Mg in the raffinate. The co-extracted Ca and Mg were fully scrubbed off the loaded Versatic 10 in 2 stages at O/A = 5:1, and pH 6.5. The other metals were stripped out of the Versatic 10 extract using a synthetic Ni spent electrolyte (60 g/L Ni, 2 M H 2 SO 4 ) in 2 stages at O/A = 9:1. This loaded strip liquor was subjected to a second circuit with Cyanex 272 (0.64 M) operated at 50 °C. Three stages were required to fully extract Co, Cu, Mn, and Zn (O/A = 2:1, pH 4), whereas the raffinate containing 82 g/L Ni was deemed suitable for electrowinning. The co-extracted Ni(II) was fully scrubbed off the loaded Cyanex 272 in only 1 stage at O/A = 5:1, and pH 4. All Co, Cu, Mn, and Zn were stripped out from the scrubbed loaded Cyanex 272 in 2 stages at O/A = 10:1 using a synthetic Co spent electrolyte (45 g/L Co, 1 M H 2 SO 4 ). The raffinate containing 58.4 g/L Co was submitted to a third circuit using a D2EHPA (0.6 M) + TBP (0.73 M) synergistic system operated at 50 °C. Zinc(II) was fully extracted by the D2EHPA + TBP system in 2 stages at pH 2 and O/A = 1:3, while Mn(II) and Cu(II) were fully extracted from the Zn-depleted raffinate in 2 stages at pH 3.5 and O/A = 2:1. The raffinate containing 58.3 g/L Co was deemed suitable for electrowinning. Copper(II), Mn(II), and Zn(II) were stripped out from the loaded D2EHPA + TBP in 3 stages at O/A = 2.5:1 using 1 M H 2 SO 4 . The real number of moles of extractants involved in the extractions and apparent equilibrium constants were estimated for all circuits. A flowsheet of the purification conceptual route is presented.

A Hydrometallurgical Route to Produce ZnO Nanoparticles and NiO Strips from the Spent Ni/ZnO Catalyst

Hydrometallurgical Process for Zinc Recovery from C.Z.O. Generated by the Steelmaking Industry with Ammonia–Ammonium Chloride Solution

Stepwise separation and recovery of molybdenum, vanadium, and nickel from spent hydrogenation catalyst

Extraction of Cu and Ni from Low-Ni Matte by a Combined Chemical Precipitation and Molten Salt Electrolysis Approach

Cleaner recycling of spent Ni–Mo/γ-Al2O3 catalyst based on mineral phase reconstruction

Preparation of nano zinc oxide by alkaline treatment of industrial zinc oxide dust

Study on Preparation of Nano-ZnO by Zinc Hypoxide in Rotary Hearth Furnace

Recovery of nickel and molybdate from ammoniacal leach liquor of spent hydrodesulfurization catalyst using LIX84 extraction

Recovery of zinc and iron from hot-dip galvanizing spent pickle liquor using solvent extraction

High-efficiency Nickel Recovery from Spent Electroless Nickel Plating Solution: Effective Degradation of High-concentration Nickel Complexes to Form Nickel Ferrite Nanomaterial via Fe 3 O 4 Catalytic Oxidation

Recovery of pure nickel powder from petroleum refinery sludge via a process consisted of leaching, cementation, precipitation, solvent extraction, and chemical reduction

Recovery of Ni, Co and Rare Earths from Spent Ni–metal Hydride Batteries and Preparation of Spherical Ni(OH)2

Recovery of nickel and iron from ferronickel powder and high nickel matte via the atmospheric leaching-hematite precipitation process

Development of a conceptual direct solvent extraction (DSX) route to produce purified concentrated cobalt and nickel solutions representing sulfuric acid leach liquor of laterite

Stepwise recycling of Fe, Cu, Zn and Ni from real electroplating sludge via coupled acidic leaching and hydrothermal and extraction routes

Synthesis of Nickel Powder with Good Hydrogen Evolution Performance from Spent Fluid Catalytic Cracking Catalysts

Separation and Recovery of Vanadium, Nickel, and Aluminum from Acid Leaching Solution of Spent Hydrodesulfurization Catalyst by a Solvent Extraction-Oxalic Acid Precipitation Process

Separation of nickel, cobalt and magnesium from the spent MH-NI and CD -NI battery anode materials

The recovery of spent Cd/Ni battery by hydro- metallurgical process

Simultaneous extraction and separation of Ni(OH) 2 , Ni powder and Ni plate from waste nickel-cobalt scrap in one spot: Control sequence of electrical reduction

Glass phase extraction for one-step separation and recovery of strategic metals from spent hydrofining catalysts