Abstract:Although significant developments have been made in the low-concentration formaldehyde monitoring in indoor air by using gas sensors, they still suffer from insufficient performance for achieving ppb-level detection. In this work, <100> oriented Si nanowires (SiNWs) with high specific surface area were prepared via metal-assisted chemical etching method (MACE), and then were uniformly coated with graphene oxide (GO) followed by the subsequent reductive process in H2/Ar atmosphere at 800 °C to obtain reduced graphene oxide (RGO). The RGO coating (RGO@n-SiNWs) obviously enhances SiNWs sensitivity to low-concentration formaldehyde, benefiting from the increased specific surface area, the sensitization effect of RGO, and the formation of p-n junction between SiNWs and RGO. Specifically, RGO@n-SiNWs exhibits a high response of 6.4 to 10 ppm formaldehyde at 300 °C, which is about 2.6 times higher than that of pristine SiNWs (~ 2.5). Furthermore, the RGO@n-SiNWs show a high response of 2.4 to 0.1 ppm formaldehyde which is the largest permissive concentration in indoor air, a low detection limit of 35 ppb obtained by non-linear fitting, and fast response/recovery times of 30 and 10 s. In the meanwhile, the sensor also shows high selectivity over other typical interfering gases such as ethanol, acetone, ammonia, methanol, xylene, and toluene, and shows a high stability over a measurement period of 6 days. These results enable the highly sensitive, selective, and stable detection of low-concentration formaldehyde to guarantee safety of indoor environment.

Multi-Wall Carbon Nanotube Gas Sensors Modified with Amino-Group to Detect Low Concentration of Formaldehyde

Fabrication and Characterization of Amino Group Functionalized Multiwall Carbon Nanotubes (MWCNT) Formaldehyde Gas Sensors

The Research and Application of Polyaniline/Multi-Walled Carbon Nanotubes Composite Sensitive Membrane for Ammonia Gas Detection

Study on Gas Sensing Property of Metal Particle Doped Multi-Walled Carbon Nanotubes

Nanoporous Functionalized WS2/MWCNTs Nanocomposite for Trimethylamine Detection Based on Quartz Crystal Microbalance Gas Sensor

N-Type Gas Sensing Characteristics of Chemically Modified Multi-Walled Carbon Nanotubes and PMMA Composite

Multi-walled Carbon Nanotube-Based Gas Sensors for NH3 Detection

In Situ Prepared Composite of Polypyrrole and Multi-Walled Carbon Nanotubes Grafted with Sodium Polystyrenesulfonate As Ammonia Gas Sensor with Wide Detection Range

Multi-Walled Carbon Nanotube-Based Gas Sensor for NH3 Detection at Room Temperature

Film Bulk Acoustic Formaldehyde Sensor with Polyethyleneimine-Modified Single-Wall Carbon Nanotubes As Sensitive Layer

An ultra-sensitive ammonia sensor based on a quartz crystal microbalance using nanofibers overlaid with carboxylic group-functionalized MWCNTs

Film Bulk Acoustic Formaldehyde Sensor with Layer-by-layer Assembled Carbon Nanotubes/polyethyleneimine Multilayers

Micro-Electromechanical Acoustic Resonator Coated With Polyethyleneimine Nanofibers For The Detection Of Formaldehyde Vapor

Carbon Nanotube-Based Field-Effect Transistor-Type Sensor with a Sensing Gate for Ppb-Level Formaldehyde Detection

On-line Monitoring of Formaldehyde in Air by Cataluminescence-Based Gas Sensor

Highly sensitive formaldehyde sensors based on CuO/ZnO composite nanofibrous mats using porous cellulose acetate fibers as templates

Nanocomposites of pre-oxidized Ti3C2Tx MXene and SnO2 nanosheets for highly sensitive and stable formaldehyde gas sensor

Effect of thiol on formaldehyde sensors based on CNTs

Enhanced Sensing Characteristics in MEMS-based Formaldehyde Gas Sensor

Reduced Graphene Oxide-Coated Si Nanowires for Highly Sensitive and Selective Detection of Indoor Formaldehyde

Flexible Room-Temperature Ammonia Gas Sensors Based on PANI-MWCNTs/PDMS Film for Breathing Analysis and Food Safety